rendered paste bodymarek@localhost ~ $ dmesg
Linux version 2.6.16-gentoo-r7 (root@localhost) (gcc version 3.4.6 (Gentoo 3.4.6 -r1, ssp-3.4.5-1.0, pie-8.7.9)) #1 SMP Wed Jun 28 16:31:17 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5020
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f69b0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff7bc0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sd a3 udev vga=791 splash=silent quiet CONSOLE=/dev/tty1
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2009.992 MHz processor.
Using pmtmr for high-res timesource
Speakup v-2.00 CVS: Wed Dec 21 14:36:03 EST 2005 : initialized
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032880k/1048512k available (2396k kernel code, 14960k reserved, 803k da ta, 200k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4028.64 BogoMIPS (lpj=8057299)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 0 0000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 0000000 0 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Total of 1 processors activated (4028.64 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 1961k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb060, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
pnp: 00:00: ioport range 0x1400-0x147f has been reserved
pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:00: ioport range 0x1800-0x187f has been reserved
pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:0b.0
IO window: 9000-9fff
MEM window: f2000000-f3ffffff
PREFETCH window: e0000000-efffffff
PCI: Bridge: 0000:00:0e.0
IO window: a000-afff
MEM window: f4000000-f6ffffff
PREFETCH window: 50000000-500fffff
PCI: Setting latency timer of device 0000:00:0e.0 to 64
audit: initializing netlink socket (disabled)
audit(1153827608.352:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
input: GenPS/2 Genius Mouse as /class/input/input1
hda: WDC WD600JB-00CRA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ASUS DRW-1608P2S, ATAPI CD/DVD-ROM drive
hdd: JLMS XJ-HD165H, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 117229295 sectors (60021 MB)
native capacity is 117231408 sectors (60022 MB)
hda: Host Protected Area disabled.
hda: 117231408 sectors (60022 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 200k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IR Q 177
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 177, io mem 0xf7005000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:09.2[C] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:02:09.2, from 10 to 9
ehci_hcd 0000:02:09.2: EHCI Host Controller
ehci_hcd 0000:02:09.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:02:09.2: irq 185, io mem 0xf6004000
ehci_hcd 0000:02:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 1-8: new high speed USB device using ehci_hcd and address 2
usb 1-8: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 193
PCI: Via IRQ fixup for 0000:02:09.0, from 10 to 1
uhci_hcd 0000:02:09.0: UHCI Host Controller
uhci_hcd 0000:02:09.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:02:09.0: irq 193, io base 0x0000a000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:09.1[B] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:02:09.1, from 5 to 9
uhci_hcd 0000:02:09.1: UHCI Host Controller
uhci_hcd 0000:02:09.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:02:09.1: irq 201, io base 0x0000a400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IR Q 209
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:02.0: irq 209, io mem 0xf7003000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IR Q 217
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:02.1: irq 217, io mem 0xf7004000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 1.20 loaded.
sata_nv 0000:00:0a.0: version 0.8
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 22 (level, high) -> IR Q 177
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 177
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 177
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c68 86:3e01 87:4063 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0)
scsi2 : sata_nv
Vendor: ATA Model: Maxtor 7L250S0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
ReiserFS: sda3: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Vendor: KINGMAX Model: USB Flash Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 1024000 512-byte hdwr sectors (524 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1024000 512-byte hdwr sectors (524 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 0:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
Adding 1052248k swap on /dev/sda2. Priority:-1 extents:1 across:1052248k
EXT3 FS on sda3, internal journal
NTFS driver 2.1.26 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 32M @ 0xf0000000
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2000
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IR Q 209
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 58694 usecs
intel8x0: clocking to 46955
Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.5 loaded
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 185
CORE cx88[0]: subsystem: 107d:6611, board: Leadtek Winfast 2000XP Expert [card=5 ,autodetected]
TV tuner 44 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[0]: Leadtek Winfast 2000XP Expert config: tuner=38, eeprom[0]=0x01
input: cx88 IR (Leadtek Winfast 2000XP as /class/input/input2
cx88[0]/0: found at 0000:02:07.0, rev: 5, irq: 185, latency: 32, mmio: 0xf400000 0
tuner 2-0060: All bytes are equal. It is not a TEA5767
tuner 2-0060: chip found @ 0xc0 (cx88[0])
tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
tda9887 2-0043: chip found @ 0x86 (cx88[0])
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
set_control id=0x980900 reg=0x310110 val=0x00 (mask 0xff)
set_control id=0x980901 reg=0x310110 val=0x3f00 (mask 0xff00)
set_control id=0x980903 reg=0x310118 val=0x00 (mask 0xff)
set_control id=0x980902 reg=0x310114 val=0x5a7f (mask 0xffff)
set_control id=0x980909 reg=0x320594 val=0x40 (mask 0x40) [shadowed]
set_control id=0x980905 reg=0x320594 val=0x20 (mask 0x3f) [shadowed]
set_control id=0x980906 reg=0x320598 val=0x40 (mask 0x7f) [shadowed]
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 201
eth0: RealTek RTL8139 at 0xf8a30000, 00:4f:4e:13:b0:7b, IRQ 201
eth0: Identified 8139 chip type 'RTL-8139B'
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 185
skge 1.5 addr 0xf6000000 irq 185 chip Yukon-Lite rev 9
skge eth1: addr 00:14:85:25:64:a2
input: PC Speaker as /class/input/input3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERM ANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] module loaded - fglrx 8.26.18 [Jun 22 2006] on minor 0
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 225
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] total GART = 33554432
[fglrx] free GART = 17559552
[fglrx] max single GART = 17559552
[fglrx] total LFB = 126873600
[fglrx] free LFB = 116387840
[fglrx] max single LFB = 116387840
[fglrx] total Inv = 0
[fglrx] free Inv = 0
[fglrx] max single Inv = 0
[fglrx] total TIM = 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 225
[fglrx:firegl_unlock] *ERROR* Process 13463 using kernel context 0
[fglrx:firegl_lock_free] *ERROR* lock was not held by 1! (*lock=0x00000000)
[fglrx:firegl_unlock] *ERROR* firegl_lock_free failed!
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 225
[fglrx:firegl_unlock] *ERROR* Process 13497 using kernel context 0
[fglrx:firegl_lock_free] *ERROR* lock was not held by 1! (*lock=0x00000000)
[fglrx:firegl_unlock] *ERROR* firegl_lock_free failed!
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 225
[fglrx:firegl_unlock] *ERROR* Process 13531 using kernel context 0
[fglrx:firegl_lock_free] *ERROR* lock was not held by 1! (*lock=0x00000000)
[fglrx:firegl_unlock] *ERROR* firegl_lock_free failed!