rendered paste bodyLinux version 2.6.23-hardened-r9 (root@yoda) (gcc version 3.4.6 (Gentoo Hardened 3.4.6-r2 p1.5, ssp-3.4.6-1.0, pie-8.7.10)) #1 Sat Apr 12 13:00:52 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003bee0000 (usable)
BIOS-e820: 000000003bee0000 - 000000003bee3000 (ACPI NVS)
BIOS-e820: 000000003bee3000 - 000000003bef0000 (ACPI data)
BIOS-e820: 000000003bef0000 - 000000003bf00000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
62MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f3900
Entering add_active_range(0, 0, 245472) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 245472
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 245472
On node 0 totalpages: 245472
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 125 pages used for memmap
HighMem zone: 15971 pages, LIFO batch:3
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F7A90, 0014 (r0 CN700 )
ACPI: RSDT 3BEE3040, 002C (r1 CN700 AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 3BEE30C0, 0074 (r1 CN700 AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 3BEE3180, 4F7E (r1 CN700 AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 3BEE0000, 0040
ACPI: APIC 3BEE8140, 005A (r1 CN700 AWRDACPI 42302E31 AWRD 0)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3bf00000:c2d00000)
Built 1 zonelists in Zone order. Total pages: 243555
Kernel command line: root=/dev/sda3
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1200.010 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 967744k/981888k available (2023k kernel code, 13596k reserved, 162k data, 2044k init, 64384k highmem)
virtual kernel memory layout:
fixmap : 0xfffa7000 - 0xfffff000 ( 352 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0201000 - 0xc0400000 (2044 kB)
.data : 0xc068a000 - 0xc06b2924 ( 162 kB)
.text : 0xc0400000 - 0xc05f9ecb (2023 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2401.37 BogoMIPS (lpj=12006865)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7c9baff 00100000 00000000 00000000 00000181 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 27c9baff 00100000 00000000 00000000 00000181 00003fcc 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: Centaur VIA Esther processor 1200MHz stepping 09
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
bios32_service: base:000f0000 length:0000b8c4 entry:00009440
PCI: PCI BIOS revision 2.10 entry at 0x9440, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22), disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:00: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
pnp: 00:02: ioport range 0x400-0x47f has been reserved
pnp: 00:02: ioport range 0x500-0x50f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: fb000000-fcffffff
PREFETCH window: f0000000-f3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
eps: Detected VIA Eden
eps: Current voltage = 860mV
eps: Current multiplier = 12
eps: Highest voltage = 860mV
eps: Highest multiplier = 12
eps: Lowest voltage = 844mV
eps: Lowest multiplier = 4
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler deadline registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Switched to high resolution mode on CPU 0
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
PCI: Bypassing VIA 8237 APIC De-Assert Message
Boot video device is 0000:01:00.0
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (16 C)
Real Time Clock Driver v1.12ac
VIA RNG detected
Linux agpgart interface v0.102
agpgart: Detected VIA VT3314 chipset
agpgart: AGP aperture is 64M @ 0xf4000000
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 16
eth0: RTL8169sc/8110sc at 0xf8814000, 00:30:18:a6:f1:02, XID 18000000 IRQ 16
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 17
eth1: RTL8169sc/8110sc at 0xf8816000, 00:30:18:a6:f1:03, XID 18000000 IRQ 17
sata_via 0000:00:0f.0: version 2.3
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
sata_via 0000:00:0f.0: routed to hard irq line 11
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0x0001ff00 ctl 0x0001fe02 bmdma 0x0001fb00 irq 18
ata2: SATA max UDMA/133 cmd 0x0001fd00 ctl 0x0001fc02 bmdma 0x0001fb08 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD800BEVS-22RST0, 04.01G04, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD800BEVS-22 04.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
pata_via 0000:00:0f.1: version 0.3.2
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
scsi2 : pata_via
scsi3 : pata_via
ata3: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fa00 irq 14
ata4: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fa08 irq 15
ata4: port disabled. ignoring.
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 19, io mem 0xfdffd000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000f900
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000f800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000f700
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 19, io base 0x0000f600
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3304
usbcore: registered new interface driver usblp
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
f71805f: Found F71805F/FG chip at 0x290, revision 19
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 2044k freed
EXT3 FS on sda3, internal journal
Adding 2000052k swap on /dev/sda1. Priority:-1 extents:1 across:2000052k
r8169: eth0: link up
r8169: eth1: link down
Clocksource tsc unstable (delta = -99891382 ns)
usblp0: removed