CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out
Sending syslog message from IF 1 to 192.168.100.10:
<130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o
ut
0x0001f1e4 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
CM> 0x0001f432 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
CM> 0x0001f7b6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
RNG-RSP Stat=Continue or ds freq=573000000 or us id=9
0x0001f7f2 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv
ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf
f...
Deleting DOCSIS 1.0 CoS Settings for SID 0x0
0x0001f8ba ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic
eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service
Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent
SB5100 CM Agent setting V1/V2 view to
SB5100 CM Agent sending deferred traps...
Done w/ deferred traps.
SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0
Ip addr is the same, not rebinding.
v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public"
CmSnmpAgent::ResetMibDefaults not restting due to factory mode
SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView
Non-Vol Settings successfully written to the device.
0x0001f8c4 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta
te: (CmDocsisCtlThread)
0x0001f8c4 ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe
ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost
in the current state (2, PropaneCmInitial)!
SB5100 CM Event Log sending deferred async messages...
Done w/ deferred msgs
Received a UCD for Upstream Channel 5!
CM>
Received a UCD for Upstream Channel 6!
Received a UCD for Upstream Channel 1!
0x0001fb3a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 2!
CM>
Received a UCD for Upstream Channel 3!
Received a UCD for Upstream Channel 4!
0x0001febe ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 5!
A target Us Chan Id was specified (9), but doesn't exist OR can't be used! Sele
cting the first available Us Channel Id...
Selecting UCD for Us Channel 5
BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f
ound for kReqDataIUC.
Upstream Frequency = 25000000
Found QAM16 = true
0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) entering...
new_us_scdma_enabled = false
fLastDsClockModeIsScdma = false
fCmDsTargetingState = kDsOkUsPending
IsDccContext() = false
0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no
w.
0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes
umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial
ranging.
Beginning initial ranging...
Using default initial upstream power = 8.0 dBmV
Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
<134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre
am (567000000 Hz)........ SUCCESS
0x0001ff40 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public"
CM> 0x00020242 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out
Sending syslog message from IF 1 to 192.168.100.10:
<130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o
ut
0x0002024c ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
CM> 0x000205c6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
RNG-RSP Stat=Continue or ds freq=573000000 or us id=11
0x0002085a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv
ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf
f...
Deleting DOCSIS 1.0 CoS Settings for SID 0x0
0x00020922 ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic
eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service
Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent
SB5100 CM Agent setting V1/V2 view to
SB5100 CM Agent sending deferred traps...
Done w/ deferred traps.
SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0
Ip addr is the same, not rebinding.
v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public"
CmSnmpAgent::ResetMibDefaults not restting due to factory mode
SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView
Non-Vol Settings successfully written to the device.
0x0002092c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta
te: (CmDocsisCtlThread)
0x0002092c ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe
ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost
in the current state (2, PropaneCmInitial)!
SB5100 CM Event Log sending deferred async messages...
Done w/ deferred msgs
NonVolDeviceDriver::NonVolDriverWrite: WARNING - Dynamic NonVol is 'full' - no
more free segments; need to erase and start over!
NonVolDeviceDriver::NonVolDriverWrite: WARNING - Erasing flash region; a power
failure here will cause settings to be lost!
0x0002094a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 3!
Received a UCD for Upstream Channel 4!
Received a UCD for Upstream Channel 5!
CM>
Received a UCD for Upstream Channel 6!
0x00020cce ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 1!
CM>
Received a UCD for Upstream Channel 2!
Received a UCD for Upstream Channel 3!
A target Us Chan Id was specified (11), but doesn't exist OR can't be used! Sel
ecting the first available Us Channel Id...
Selecting UCD for Us Channel 3
BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f
ound for kReqDataIUC.
Upstream Frequency = 21000000
Found QAM16 = true
0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) entering...
new_us_scdma_enabled = false
fLastDsClockModeIsScdma = false
fCmDsTargetingState = kDsOkUsPending
IsDccContext() = false
0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no
w.
0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes
umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial
ranging.
Beginning initial ranging...
Using default initial upstream power = 8.0 dBmV
Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
<134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre
am (567000000 Hz)........ SUCCESS
0x00020fe4 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public"
0x00021052 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out
Sending syslog message from IF 1 to 192.168.100.10:
<130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o
ut
0x000211ec ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
RNG-RSP Stat=Continue or ds freq=573000000 or us id=9
0x0002134a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv
ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf
f...
Deleting DOCSIS 1.0 CoS Settings for SID 0x0
0x00021412 ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic
eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service
Flows, along with associated Classifiers and PHS rules...
Stopping DHCP/ToD/TFTP (client requested)...
BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent
SB5100 CM Agent setting V1/V2 view to
SB5100 CM Agent sending deferred traps...
Done w/ deferred traps.
SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0
Ip addr is the same, not rebinding.
v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public"
CmSnmpAgent::ResetMibDefaults not restting due to factory mode
SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView
Non-Vol Settings successfully written to the device.
0x0002141c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta
te: (CmDocsisCtlThread)
0x0002141c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
0x0002141c ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe
ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost
in the current state (2, PropaneCmInitial)!
SB5100 CM Event Log sending deferred async messages...
Done w/ deferred msgs
Received a UCD for Upstream Channel 2!
CM>
Received a UCD for Upstream Channel 3!
Received a UCD for Upstream Channel 4!
0x0002175a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 5!
CM>
Received a UCD for Upstream Channel 6!
Received a UCD for Upstream Channel 1!
0x00021ade ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg
tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori
ng...
Received a UCD for Upstream Channel 2!
A target Us Chan Id was specified (9), but doesn't exist OR can't be used! Sele
cting the first available Us Channel Id...
Selecting UCD for Us Channel 2
BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f
ound for kReqDataIUC.
Upstream Frequency = 21000000
Found QAM16 = true
0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) entering...
new_us_scdma_enabled = false
fLastDsClockModeIsScdma = false
fCmDsTargetingState = kDsOkUsPending
IsDccContext() = false
0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun
chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no
w.
0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes
umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial
ranging.
Beginning initial ranging...
Using default initial upstream power = 8.0 dBmV
Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS
Sending syslog message from IF 1 to 192.168.100.10:
<134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre
am (567000000 Hz)........ SUCCESS
0x00021b60 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public"
CM> Adjusting the initial ranging power to 33.0 dBmV...
Logging event: No Ranging Response received - T3 time-out
Sending syslog message from IF 1 to 192.168.100.10:
<130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o
ut
0x00021cdc ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK
ET_ERROR: 65
docsDevEvSyslog::Send - sendto failure -1
CM> 0x00021e62 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
CM> 0x000221e6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM
acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig
noring...
RNG-RSP Stat=Continue or ds freq=573000000 or us id=9
0x000222ea ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv
ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf
f...
Connection to host lost.
C:\Documents and Settings\home>