rendered paste body=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint P80 series
Device Model: SAMSUNG SP1614N
Serial Number: S016J10Y904568
Firmware Version: TM100-30
User Capacity: 160.041.885.696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sun Apr 13 22:46:13 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: (6000) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 100) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 5568
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2300
5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Half_Minutes 0x0032 099 099 000 Old_age Always - 8177h+42m
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 1
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1424
194 Temperature_Celsius 0x0022 148 115 000 Old_age Always - 30
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 4024560
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 051 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 940 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 940 occurred at disk power-on lifetime: 278 hours (11 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 b0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 b0 00 00:00:53.125 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 b0 00 00:00:53.125 IDENTIFY DEVICE
10 00 ff 01 00 00 b0 00 00:00:53.125 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 bf 00 00:00:53.125 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 b0 00 00:00:53.063 IDENTIFY DEVICE
Error 939 occurred at disk power-on lifetime: 278 hours (11 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 b0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 b0 00 00:00:24.875 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 b0 00 00:00:24.875 IDENTIFY DEVICE
10 00 ff 01 00 00 b0 00 00:00:24.875 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 bf 00 00:00:24.875 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 b0 00 00:00:24.813 IDENTIFY DEVICE
Error 938 occurred at disk power-on lifetime: 278 hours (11 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 b0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 b0 00 00:02:02.250 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 b0 00 00:02:02.250 IDENTIFY DEVICE
10 00 ff 01 00 00 b0 00 00:02:02.250 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 bf 00 00:02:02.250 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 b0 00 00:02:02.250 IDENTIFY DEVICE
Error 937 occurred at disk power-on lifetime: 278 hours (11 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 b0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 b0 00 00:01:11.688 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 b0 00 00:01:11.688 IDENTIFY DEVICE
10 00 ff 01 00 00 b0 00 00:01:11.688 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 bf 00 00:01:11.688 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 b0 00 00:01:11.688 IDENTIFY DEVICE
Error 936 occurred at disk power-on lifetime: 278 hours (11 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 4f c2 b0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d9 00 01 4f c2 b0 00 00:00:26.563 SMART DISABLE OPERATIONS
ec 00 ff 01 00 00 b0 00 00:00:26.563 IDENTIFY DEVICE
10 00 ff 01 00 00 b0 00 00:00:26.563 RECALIBRATE [OBS-4]
91 00 ff 01 00 00 bf 00 00:00:26.563 INITIALIZE DEVICE PARAMETERS [OBS-6]
ec 00 ff 01 00 00 b0 00 00:00:25.000 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Abort offline test Aborted by host 90% 7542 -
Device does not support Selective Self Tests/Logging