root@OpenWrt:~# dmesg
CPU revision is: 00029006
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Linux version 2.4.34 (nbd@ds10) (gcc version 3.4.6 (OpenWrt-2.0)) #3 Sun Sep 30 20:33:21 CEST 2007
Setting the PFC to its default value
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM4704 rev 8 at 264 MHz
Using 132.000 MHz high precision timer.
Calibrating delay loop... 262.96 BogoMIPS
Memory: 14224k/16384k available (1462k kernel code, 2160k reserved, 100k data, 80k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:01.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:17:31:b4:23:0c
PCI: Setting latency timer of device 00:02.0 to 64
eth1: Broadcom 47xx 10/100BaseT Ethernet 40:10:18:00:00:2d
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x800000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x121cc8
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x000be400-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007f0000-0x00800000 : "nvram"
0x001f0000-0x007f0000 : "rootfs_data"
sflash: found no supported devices
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 360 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 80k freed
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'ASUS WL-500g Premium'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Probing device eth0: found!
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 01:03.2 (0000 -> 0002)
ehci_hcd 01:03.2: PCI device 1106:3104
ehci_hcd 01:03.2: irq 2, pci mem c00e8000
usb.c: new USB bus registered, assigned bus number 1
EHCI: Enabling VIA 6212 workarounds
ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 4 ports detected
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Journalled Block Device driver loaded
hub.c: new USB device 01:03.2-1, assigned address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Maxtor 6 Model: L160P0 Rev: 0 0
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
hub.c: new USB device 01:03.2-2, assigned address 3
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 01:03.2-2.3, assigned address 4
usb.c: USB device 4 (vend/prod 0x4a9/0x10c8) is not claimed by any active driver.
hub.c: new USB device 01:03.2-2.4, assigned address 5
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 01:03.2-2.4.1, assigned address 6
usb.c: USB device 6 (vend/prod 0x6f8/0xc000) is not claimed by any active driver.
hub.c: new USB device 01:03.2-2.4.4, assigned address 7
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: STORAGE DEVICE Rev: 9317
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi removable disk sdc at scsi1, channel 0, id 0, lun 1
Attached scsi removable disk sdd at scsi1, channel 0, id 0, lun 2
Attached scsi removable disk sde at scsi1, channel 0, id 0, lun 3
sdb: Unit Not Ready, sense:
Current 00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
unable to read partition table
sdc: Unit Not Ready, sense:
Current 00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
unable to read partition table
sdd: Unit Not Ready, sense:
Current 00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun2: I/O error: dev 08:30, sector 0
I/O error: dev 08:30, sector 0
unable to read partition table
sde: Unit Not Ready, sense:
Current 00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sde : READ CAPACITY failed.
sde : status = 1, message = 00, host = 0, driver = 08
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
sde : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun3: I/O error: dev 08:40, sector 0
I/O error: dev 08:40, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 7
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Enabling device 01:03.0 (0000 -> 0001)
uhci.c: USB UHCI at I/O 0x100, IRQ 2
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 01:03.1 (0000 -> 0001)
uhci.c: USB UHCI at I/O 0x120, IRQ 2
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
jffs2.bbc: SIZE compression mode activated.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
PCI: Setting latency timer of device 01:02.0 to 64
PCI: Enabling device 01:02.0 (0004 -> 0006)
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.80.53.0
eth0.1: add 01:00:5e:00:00:01 mcast address to master interface
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PCI: Setting latency timer of device 00:03.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10C8
printer.c: v0.13: USB Printer Device Class driver
device wl0 entered promiscuous mode
wl0: attempt to add interface with same source address.
br-lan: port 2(wl0) entering learning state
br-lan: port 2(wl0) entering forwarding state
br-lan: topology change detected, propagating