LOM event: +0h4m17s host reset
meout waiting for ARP/RARP packet
p
Processor Speed = [Speed Jumper = 5] 500 MHz
Baud rate is 9600
8 Data bits, 1 stop bits, no parity (configured from lom)
Firmware CORE Sun Microsystems, Inc.
@(#) core 1.0.3 2001/01/03 13:54
Button Power ON
Verifying NVRAM...Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 36a0bc04
MCR1 = c0804000
MCR2 = ff0ffff
MCR3 = 3ff
Ecache Size = 256 KB
NVRAM Test
Icache Test
Dcache Test
MMU Test
FPU Test
Ecache Tag Addr Test
Ecache RAM Addr Test
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x60000000
MEMSIZE=0x20000000
Data Line Test
Core Memory Test
Clearing memory...including Unix retained memory...Done
Turning ON MMUs Done
Copy ROM to RAM (168992 bytes) Done
Orig PC=0x1fff0007e48 New PC=0xf0f07ea0
Processor Speed=500MHz
Memory Data Line Test
Memory Addr Line w/ Ecache Test
ECC Block Memory Test
Looking for Dropin cPOST ... found
Copying Client...Done
Transferring control to Client...
Sun Microsystems, Inc. cPOST
@(#) cpost 1.0.3 2001/01/03 13:55
All Basic UltraSPARC IIe PBM Tests
Init CPU PBM
PIO Decoder And BCT Test
CPU IOMMU Reg Test
CPU IOMMU RAM NTA Test
CPU IOMMU CAM NTA Test
CPU IOMMU RAM Address Test
CPU IOMMU CAM Address Test
IOMMU TLB Compare Test
IOMMU TLB Flush Test
PBM Control/Status Reg Test
PBM Diag Reg Test
CPU PBM Reg Test
All Basic APB Simba Tests
Init PCI
All Basic RIO Tests (RIO# 1)
RIO Ebus Config Space Reg Test
RIO Network Config Space Reg Test
RIO Firewire Config Space Reg Test
RIO USB Config Space Reg Test
All Basic RIO Tests (RIO# 2)
RIO Ebus Config Space Reg Test
RIO Network Config Space Reg Test
RIO Firewire Config Space Reg Test
RIO USB Config Space Reg Test
All Basic SCSI Controller Tests
Symbios SCSI Controller PCI Config Space Test
All Basic SCSI Controller Tests
Symbios SCSI Controller PCI Config Space Test
Basic SouthBridge Tests
Southbridge ISA Config Space Reg Test
Southbridge PMU Config Space Reg Test
Southbridge IDE Config Space Reg Test
Southbridge Audio Config Space Reg Test
All Memory Stress Tests
Consist Write Data Test
Resetting...
p
Processor Speed = 500 MHz
Baud rate is 9600
8 Data bits, 1 stop bits, no parity (configured from lom)
Firmware CORE Sun Microsystems, Inc.
@(#) core 1.0.3 2001/01/03 13:54
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 36a0bc04
MCR1 = c0804000
MCR2 = ff0ffff
MCR3 = 3ff
Ecache Size = 256 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x60000000
MEMSIZE=0x20000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (168992 bytes) Done
Orig PC=0x1fff0007e48 NeC ... Not found
Processor Speed=500MHz ..
Entering Firmware CORE User Interface...
Type "help" for help
Will exit to client if no activity detected for 10 secs
> > help
To get this help : help
To allocate memory buffer: malloc <size>
To free memory buffer : free <addr>
To block copy memory : bcopy <src> <dest> <#bytes>
To dump memory : dump <addr> <#bytes> [asi]
To read an address : [safe-]peek <addr> <1|2|4|8> [asi]
To write to an address : poke <addr> <1|2|4|8> <data> [asi]
To update Flash PROM : flash-update <dev> <file-path>
To load a file : load <device> <file-path> <addr>
Jump to an address : go <addr>
Execute client : execute [client-name]
Print NVRAM data : print-nvram
Write to NVRAM variable : set-nvram <variable-name|ID> <data>
Read an NVRAM variable : get-nvram <variable-name|ID>
Delete an NVRAM variable : delete-nvram <ID>
Set NVRAM vars to default: set-defaults
Call a trap function : trap <trap#> <par0> ... <par5>
Soft Reset : reset
To change input device : input-device <tty|kbd>
To initialize PCI : init-pci
To show all pci devices : show-pci-devs
To show pci config space : show-pci-space <bus#> <device#> <function#> <offset>
To show pci nexus nodes : show-nexus-nodes
To remove a pci device : rm-pci-dev <device#>
To add a pci device : add-pci-dev <device#>
To remove all pci devices: rm-pci-devs
To add all pci devices : add-pci-devs
To execute UI cmd in loop: loop <count> <command>
NOTE: All numbers are considered as HEX numbers
> show-disks
Command usage error, type "help" for help
> print-nvram
Fixed offset NVRAM variables :
user-interface = 0
run-post = ff C
trap-state = 60 ..
msg-verbosity = 3V..
ID based NVRAM variables :
ID=6f #bytes=6f Data=74 00 05 1d 14 8b 85 1d 14 8b c3 00 0a 00 00 00 00 04 62 6f 6f 74 00 05 1d 14 8b 85 1d 14 8b c3 00 0a 00 00 00 00 04 62 6f 6f 74 00 05 1d 14 8b 85 1d 14 8b c3 00 0a 00 00 00 00 04 62 6f 6f 74 00 05 1d 14 8b 85 1d 14 8b c3 00 0a 00 00 00 00 04 62 6f 6f 74 00 05 1d 14 8b 85 fa 93 87 c9 00
ID=74 #bytes=31 Data=64 30 20 2f 70 63 69 40 31 66 2c 30 2f 70 63 69 40 31 2f 73 63 73 69 40 38 2f 64 69 73 6b 40 31 2c 30 3a 61 84 1d d3 ca c9 00 34 64 65 76 61 6c 69
ID=61 #bytes=73 Data=20 76 78 2d 63 30 74 31 64 30 20 2f 70 63 69 40 31 66 2c 30 2f 70 63 69 40 31 2f 73 63 73 69 40 38 2f 64 69 73 6b 40 31 2c 30 3a 61 ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ID=ee #bytes=48 Data=02 00 63 50 4f 53 54 20 70 61 73 73 00 65 74 65 63 74 65 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ID=ef #bytes=42 Data=d8 07 03 1b 15 2b 01 00 64 00 64 00 00 00 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff f7 ff ff ff ff ff ff
> Minicom2.2Minico
Command usage error, type "help" for help
> openboot
Command usage error, type "help" for help
> help
To get this help : help
To allocate memory buffer: malloc <size>
To free memory buffer : free <addr>
To block copy memory : bcopy <src> <dest> <#bytes>
To dump memory : dump <addr> <#bytes> [asi]
To read an address : [safe-]peek <addr> <1|2|4|8> [asi]
To write to an address : poke <addr> <1|2|4|8> <data> [asi]
To update Flash PROM : flash-update <dev> <file-path>
To load a file : load <device> <file-path> <addr>
Jump to an address : go <addr>
Execute client : execute [client-name]
Print NVRAM data : print-nvram
Write to NVRAM variable : set-nvram <variable-name|ID> <data>
Read an NVRAM variable : get-nvram <variable-name|ID>
Delete an NVRAM variable : delete-nvram <ID>
Set NVRAM vars to default: set-defaults
Call a trap function : trap <trap#> <par0> ... <par5>
Soft Reset : reset
To change input device : input-device <tty|kbd>
To initialize PCI : init-pci
To show all pci devices : show-pci-devs
To show pci config space : show-pci-space <bus#> <device#> <function#> <offset>
To show pci nexus nodes : show-nexus-nodes
To remove a pci device : rm-pci-dev <device#>
To add a pci device : add-pci-dev <device#>
To remove all pci devices: rm-pci-devs
To add all pci devices : add-pci-devs
To execute UI cmd in loop: loop <count> <command>
NOTE: All numbers are considered as HEX numbers
> dump 0 ##50
> dump 0 #50
> n okay
Command usage error, type "help" for help
> n
Command usage error, type "help" for help
> banner
Command usage error, typeC ... Not foundp
> execute ..
Entering Firmware CORE User Interface...
Type "help" for help
Will exit to client if no activity detected for 10 secs
> >
> execute openboot
Looking for Dropin openboot ... Not found
Entering Firmware CORE User Interface...
Type "help" for help
> execute lom
Looking for Dropin lom ... Not found
Entering Firmware CORE User Interface...
Type "help" for help
>