rendered paste bodySDA
===
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar RE Serial ATA series
Device Model: WDC WD4000YR-01PLB0
Serial Number: WD-WMAMY1569851
Firmware Version: 01.06A01
User Capacity: 400,088,457,216 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 published, ANSI INCITS 397-2005
Local Time is: Mon Mar 24 18:34:24 2008 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10530) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 152) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 222 222 021 Pre-fail Always - 5925
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always - 28
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10383
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 28
194 Temperature_Celsius 0x0022 125 120 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 66 -
SDD
===
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10 family
Device Model: ST3750640AS
Serial Number: 5QD0CYFH
Firmware Version: 3.AAK
User Capacity: 750,156,374,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Mar 24 18:40:23 2008 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 202) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 089 085 006 Pre-fail Always - 232009739
3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 8
5 Reallocated_Sector_Ct 0x0033 098 098 036 Pre-fail Always - 91
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 259511910
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5587
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 5
187 Unknown_Attribute 0x0032 046 046 000 Old_age Always - 54
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 072 057 045 Old_age Always - 521338908
194 Temperature_Celsius 0x0022 028 043 000 Old_age Always - 28 (Lifetime Min/Max 0/19)
195 Hardware_ECC_Recovered 0x001a 061 048 000 Old_age Always - 84739387
197 Current_Pending_Sector 0x0012 059 059 000 Old_age Always - 841
198 Offline_Uncorrectable 0x0010 059 059 000 Old_age Offline - 841
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 54 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 54 occurred at disk power-on lifetime: 5586 hours (232 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 37 8d b1 e0 Error: UNC at LBA = 0x00b18d37 = 11636023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 37 8d b1 e0 00 04:53:22.257 READ DMA EXT
27 00 00 00 00 00 e0 00 04:53:22.251 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 04:53:20.307 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 04:53:20.246 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 04:53:20.242 READ NATIVE MAX ADDRESS EXT
Error 53 occurred at disk power-on lifetime: 5586 hours (232 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 37 8d b1 e0 Error: UNC at LBA = 0x00b18d37 = 11636023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 37 8d b1 e0 00 04:53:22.257 READ DMA EXT
27 00 00 00 00 00 e0 00 04:53:22.251 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 04:53:20.307 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 04:53:20.246 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 04:53:20.242 READ NATIVE MAX ADDRESS EXT
Error 52 occurred at disk power-on lifetime: 5586 hours (232 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 37 8d b1 e0 Error: UNC at LBA = 0x00b18d37 = 11636023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 37 8d b1 e0 00 04:53:16.067 READ DMA EXT
27 00 00 00 00 00 e0 00 04:53:16.062 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 04:53:20.307 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 04:53:20.246 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 04:53:20.242 READ NATIVE MAX ADDRESS EXT
Error 51 occurred at disk power-on lifetime: 5586 hours (232 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 37 8d b1 e0 Error: UNC at LBA = 0x00b18d37 = 11636023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 37 8d b1 e0 00 04:53:16.067 READ DMA EXT
27 00 00 00 00 00 e0 00 04:53:16.062 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 04:53:16.052 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 04:53:15.991 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 04:53:15.985 READ NATIVE MAX ADDRESS EXT
Error 50 occurred at disk power-on lifetime: 5586 hours (232 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 37 8d b1 e0 Error: UNC at LBA = 0x00b18d37 = 11636023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 37 8d b1 e0 00 04:53:16.067 READ DMA EXT
27 00 00 00 00 00 e0 00 04:53:16.062 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 04:53:16.052 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 04:53:15.991 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 04:53:15.985 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.