rendered paste body[ 0.000000] BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003df00000 (usable)
[ 0.000000] BIOS-e820: 000000003df00000 - 000000003df17000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003df17000 - 000000003df80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003df80000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 253696) 1 entries of 3200 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI present.
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000003df00000
[ 0.000000] Entering add_active_range(0, 0, 157) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 253696) 1 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-000000003df00000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 157
[ 0.000000] 0: 256 -> 253696
[ 0.000000] On node 0 totalpages: 253597
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1127 pages reserved
[ 0.000000] DMA zone: 2814 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 3412 pages used for memmap
[ 0.000000] DMA32 zone: 246188 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] MPTABLE: OEM ID: nVIDIA MPTABLE: Product ID: C51-MCP51 MPTABLE: APIC at: 0xFEE00000
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] Processor #1
[ 0.000000] I/O APIC #2 at 0xFEC00000.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Processors: 2
[ 0.000000] swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
[ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 34696 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 249002
[ 0.000000] Kernel command line: root=UUID=21edb400-2b8b-4bc4-a0b1-d6529b929d98 ro quiet splash apm=off acpi=off noapic
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Marking TSC unstable due to TSCs unsynchronized
[ 12.811243] time.c: Detected 1607.333 MHz processor.
[ 12.814825] Console: colour VGA+ 80x25
[ 12.814841] Checking aperture...
[ 12.814844] CPU 0: aperture @ 130000000 size 32 MB
[ 12.814847] Aperture too small (32 MB)
[ 12.822004] No AGP bridge found
[ 12.834274] Memory: 988632k/1014784k available (2274k kernel code, 25756k reserved, 1185k data, 296k init)
[ 12.834324] SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 12.913231] Calibrating delay using timer specific routine.. 3217.63 BogoMIPS (lpj=6435262)
[ 12.913267] Security Framework v1.0.0 initialized
[ 12.913273] SELinux: Disabled at boot.
[ 12.913376] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 12.914122] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 12.914399] Mount-cache hash table entries: 256
[ 12.914541] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 12.914544] CPU: L2 Cache: 256K (64 bytes/line)
[ 12.914548] CPU 0/0 -> Node 0
[ 12.914550] CPU: Physical Processor ID: 0
[ 12.914552] CPU: Processor Core ID: 0
[ 12.914569] SMP alternatives: switching to UP code
[ 12.914811] Early unpacking initramfs... done
[ 13.277715] Using local APIC timer interrupts.
[ 13.339927] result 12557286
[ 13.339929] Detected 12.557 MHz APIC timer.
[ 13.341283] SMP alternatives: switching to SMP code
[ 13.341395] Booting processor 1/2 APIC 0x1
[ 13.351746] Initializing CPU#1
[ 13.353196] spurious 8259A interrupt: IRQ7.
[ 13.429493] Calibrating delay using timer specific routine.. 3221.10 BogoMIPS (lpj=6442217)
[ 13.429501] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 13.429504] CPU: L2 Cache: 256K (64 bytes/line)
[ 13.429507] CPU 1/1 -> Node 0
[ 13.429509] CPU: Physical Processor ID: 0
[ 13.429510] CPU: Processor Core ID: 1
[ 13.429578] AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02
[ 13.433237] Brought up 2 CPUs
[ 13.464126] migration_cost=116
[ 13.464037] NET: Registered protocol family 16
[ 13.464143] PCI: Using configuration type 1
[ 13.464634] ACPI: Interpreter disabled.
[ 13.464637] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 13.464650] pnp: PnP ACPI: disabled
[ 13.464709] PCI: Probing PCI hardware
[ 13.464717] PCI: Probing PCI hardware (bus 00)
[ 13.465986] PCI: Transparent bridge - 0000:00:10.0
[ 13.467826] PCI: Discovered primary peer bus 04 [IRQ]
[ 13.467837] PCI: Using IRQ router default [10de/0260] at 0000:00:0a.0
[ 13.467980] NET: Registered protocol family 8
[ 13.467983] NET: Registered protocol family 20
[ 13.468439] PCI: Bridge: 0000:00:02.0
[ 13.468443] IO window: 4000-4fff
[ 13.468447] MEM window: b3000000-b31fffff
[ 13.468450] PREFETCH window: d0000000-d01fffff
[ 13.468453] PCI: Bridge: 0000:00:03.0
[ 13.468455] IO window: disabled.
[ 13.468458] MEM window: b3200000-b33fffff
[ 13.468461] PREFETCH window: disabled.
[ 13.468465] PCI: Bridge: 0000:00:10.0
[ 13.468466] IO window: disabled.
[ 13.468470] MEM window: b3400000-b34fffff
[ 13.468474] PREFETCH window: disabled.
[ 13.468484] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 13.468492] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 13.468500] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 13.468606] NET: Registered protocol family 2
[ 13.505263] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 13.505721] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 13.508198] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 13.508961] TCP: Hash tables configured (established 131072 bind 65536)
[ 13.508965] TCP reno registered
[ 13.521335] checking if image is initramfs... it is
[ 14.366554] Freeing initrd memory: 7206k freed
[ 14.372447] audit: initializing netlink socket (disabled)
[ 14.372465] audit(1205882706.504:1): initialized
[ 14.377328] VFS: Disk quotas dquot_6.5.1
[ 14.377464] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 14.377631] io scheduler noop registered
[ 14.377634] io scheduler anticipatory registered
[ 14.377636] io scheduler deadline registered
[ 14.377863] io scheduler cfq registered (default)
[ 14.377880] Boot video device is 0000:00:05.0
[ 22.592807] 0000:00:0b.1 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
[ 22.593174] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 22.593200] assign_interrupt_mode Found MSI capability
[ 22.593203] Allocate Port Service[0000:00:02.0:pcie00]
[ 22.593277] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 22.593299] assign_interrupt_mode Found MSI capability
[ 22.593302] Allocate Port Service[0000:00:03.0:pcie00]
[ 22.634480] Real Time Clock Driver v1.12ac
[ 22.634561] Linux agpgart interface v0.102 (c) Dave Jones
[ 22.634565] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 22.635968] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 22.636148] input: Macintosh mouse button emulation as /class/input/input0
[ 22.636275] PNP: No PS/2 controller found. Probing ports directly.
[ 22.652150] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 22.652158] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 22.652381] mice: PS/2 mouse device common for all mice
[ 22.652564] TCP cubic registered
[ 22.653228] NET: Registered protocol family 1
[ 22.653495] /build/buildd/linux-source-2.6.22-2.6.22/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 22.653505] Freeing unused kernel memory: 296k freed
[ 22.665040] input: AT Translated Set 2 keyboard as /class/input/input1
[ 23.876733] AppArmor: AppArmor initialized<5>audit(1205882715.816:2): type=1505 info="AppArmor initialized" pid=1155
[ 23.883405] fuse init (API version 7.8)
[ 23.889360] Failure registering capabilities with primary security module.
[ 23.965316] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 24.628782] usbcore: registered new interface driver usbfs
[ 24.628817] usbcore: registered new interface driver hub
[ 24.628843] usbcore: registered new device driver usb
[ 24.629698] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 24.629846] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 24.629854] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 24.630008] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 24.630029] ohci_hcd 0000:00:0b.0: irq 11, io mem 0xb0004000
[ 24.636545] SCSI subsystem initialized
[ 24.642810] libata version 2.21 loaded.
[ 24.704799] usb usb1: configuration #1 chosen from 1 choice
[ 24.704838] hub 1-0:1.0: USB hub found
[ 24.704858] hub 1-0:1.0: 8 ports detected
[ 24.736427] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 24.810233] sata_nv 0000:00:0e.0: version 3.4
[ 24.810248] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
[ 24.810404] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 24.811137] scsi0 : sata_nv
[ 24.814803] scsi1 : sata_nv
[ 24.815143] ata1: SATA max UDMA/133 cmd 0x00000000000130c0 ctl 0x00000000000130b6 bmdma 0x0000000000013090 irq 5
[ 24.815149] ata2: SATA max UDMA/133 cmd 0x00000000000130b8 ctl 0x00000000000130b2 bmdma 0x0000000000013098 irq 5
[ 25.112616] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 25.280616] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 25.288793] ata1.00: ATA-7: ST9100824AS, 7.24, max UDMA/100
[ 25.288799] ata1.00: 195371568 sectors, multi 16: LBA48
[ 25.304777] ata1.00: configured for UDMA/100
[ 25.322321] usb 1-2: configuration #1 chosen from 1 choice
[ 25.336075] usbcore: registered new interface driver hiddev
[ 25.341350] input: USB Mouse as /class/input/input2
[ 25.341375] input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:0b.0-2
[ 25.341389] usbcore: registered new interface driver usbhid
[ 25.341393] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 25.616573] ata2: SATA link down (SStatus 0 SControl 300)
[ 25.627347] scsi 0:0:0:0: Direct-Access ATA ST9100824AS 7.24 PQ: 0 ANSI: 5
[ 25.628057] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 25.628064] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 25.628128] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 25.628163] ehci_hcd 0000:00:0b.1: debug port 1
[ 25.628167] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 25.628178] ehci_hcd 0000:00:0b.1: irq 7, io mem 0xb0005000
[ 25.628188] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.627949] usb 1-2: USB disconnect, address 2
[ 25.628350] usb usb2: configuration #1 chosen from 1 choice
[ 25.628391] hub 2-0:1.0: USB hub found
[ 25.628398] hub 2-0:1.0: 8 ports detected
[ 25.733907] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 25.733918] forcedeth: using HIGHDMA
[ 25.734649] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 25.734657] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 25.743033] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 25.743048] sd 0:0:0:0: [sda] Write Protect is off
[ 25.743052] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.743068] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.743142] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 25.743151] sd 0:0:0:0: [sda] Write Protect is off
[ 25.743154] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.743169] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.743175] sda: sda1 sda2 < sda5 > sda3 sda4
[ 25.789327] sd 0:0:0:0: [sda] Attached SCSI disk
[ 25.794514] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 26.148227] Attempting manual resume
[ 26.148232] swsusp: Resume From Partition 8:3
[ 26.148234] PM: Checking swsusp image.
[ 26.148464] PM: Resume from disk failed.
[ 26.175392] kjournald starting. Commit interval 5 seconds
[ 26.175103] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.236232] usb 1-2: new low speed USB device using ohci_hcd and address 3
[ 26.252565] eth0: forcedeth.c: subsystem: 0103c:30b7 bound to 0000:00:14.0
[ 26.252934] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 26.252959] NFORCE-MCP51: chipset revision 241
[ 26.252962] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 26.252967] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 26.252973] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 26.252984] ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:DMA, hdb:pio
[ 26.252996] Probing IDE interface ide0...
[ 26.446153] usb 1-2: configuration #1 chosen from 1 choice
[ 26.456228] input: USB Mouse as /class/input/input3
[ 26.456252] input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:0b.0-2
[ 26.992576] hda: HL-DT-ST DVDRAM GSA-4084N, ATAPI CD/DVD-ROM drive
[ 27.329725] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 27.381807] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b3400000-b34007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 35.607352] NET: Registered protocol family 17
[ 35.708088] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 35.712553] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 35.806853] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 35.806883] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 35.949263] sdhci: Secure Digital Host Controller Interface driver
[ 35.949268] sdhci: Copyright(c) Pierre Ossman
[ 35.949991] sdhci: SDHCI controller found at 0000:07:05.1 [1180:0822] (rev 19)
[ 35.950526] mmc0: SDHCI at 0xb3400800 irq 11 DMA
[ 35.989259] ndiswrapper version 1.45 loaded (smp=yes)
[ 36.449046] ndiswrapper (link_pe_images:577): fixing KI_USER_SHARED_DATA address in the driver
[ 36.452282] ndiswrapper: driver bcmwl5 (Broadcom,07/11/2007, 4.150.29.0) loaded
[ 36.452800] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 36.452846] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 36.456174] ndiswrapper (IoConnectInterrupt:567): request for irq 0 failed
[ 36.456180] ndiswrapper: request for IRQ 0 failed
[ 36.456320] ndiswrapper (mp_init:263): couldn't initialize device: C000009A
[ 36.456328] ndiswrapper (pnp_start_device:440): Windows driver couldn't initialize the device (C0000001)
[ 36.456344] ndiswrapper (mp_halt:305): device ffff8100356c7780 is not initialized - not halting
[ 36.456355] ndiswrapper: device eth%d removed
[ 36.456376] ndiswrapper: probe of 0000:03:00.0 failed with error -22
[ 36.456462] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 36.461770] usbcore: registered new interface driver ndiswrapper
[ 36.462449] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007
[ 36.504744] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
[ 36.504755] Uniform CD-ROM driver Revision: 3.20
[ 36.535431] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
[ 36.601719] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[ 37.344059] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 38.383301] ALSA /usr/src/modules/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:558: hda_intel: azx_get_response timeout, switching to polling mode...
[ 39.636860] lp: driver loaded but no devices found
[ 39.827155] Adding 514072k swap on /dev/sda3. Priority:-1 extents:1 across:514072k
[ 40.227062] EXT3 FS on sda4, internal journal
[ 41.044694] NET: Registered protocol family 10
[ 41.044875] lo: Disabled Privacy Extensions
[ 43.043736] powernow_k8: Unknown symbol acpi_processor_notify_smm
[ 43.043786] powernow_k8: Unknown symbol acpi_processor_unregister_performance
[ 43.043895] powernow_k8: Unknown symbol acpi_processor_register_performance
[ 43.110033] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 43.110085] acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
[ 43.110209] acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
[ 43.110268] acpi_cpufreq: Unknown symbol acpi_processor_register_performance
[ 47.005058] Failure registering capabilities with primary security module.
[ 48.044452] ppdev: user-space parallel port driver
[ 48.270208] audit(1205893540.828:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4777 profile="/usr/sbin/cupsd"
[ 51.350343] eth0: no IPv6 routers present
[ 56.190672] Failure registering capabilities with primary security module.
[ 56.383083] Bluetooth: Core ver 2.11
[ 56.383147] NET: Registered protocol family 31
[ 56.383150] Bluetooth: HCI device and connection manager initialized
[ 56.383155] Bluetooth: HCI socket layer initialized
[ 56.399739] Bluetooth: L2CAP ver 2.8
[ 56.399746] Bluetooth: L2CAP socket layer initialized
[ 56.440702] Bluetooth: RFCOMM socket layer initialized
[ 56.440822] Bluetooth: RFCOMM TTY layer initialized
[ 56.440825] Bluetooth: RFCOMM ver 1.8
[ 60.239724] ieee1394: Host added: ID:BUS[0-00:1023] GUID[009fc0004427c800]
[ 171.622325] ieee80211_crypt: registered algorithm 'NULL'
[ 171.634018] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 171.634024] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 171.725286] bcm43xx driver
[ 171.725445] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 171.725456] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 172.142734] bcm43xx: Cannot register IRQ0
[ 176.128983] Trying to free already-free IRQ 0
[ 176.207113] bcm43xx: IRQ_READY timeout
[ 200.095171] bcm43xx: IRQ_READY timeout
[ 223.802627] bcm43xx: IRQ_READY timeout
[ 237.354090] irq 7: nobody cared (try booting with the "irqpoll" option)
[ 237.354098]
[ 237.354099] Call Trace:
[ 237.354102] <IRQ> [<ffffffff8026aaee>] __report_bad_irq+0x1e/0x80
[ 237.354131] [<ffffffff8026add3>] note_interrupt+0x283/0x2c0
[ 237.354141] [<ffffffff8026bbcc>] handle_level_irq+0x10c/0x140
[ 237.354149] [<ffffffff8020c6ab>] do_IRQ+0x7b/0x100
[ 237.354153] [<ffffffff80209010>] default_idle+0x0/0x40
[ 237.354158] [<ffffffff8020a3a1>] ret_from_intr+0x0/0xa
[ 237.354161] <EOI> [<ffffffff80422270>] unix_poll+0x0/0xb0
[ 237.354174] [<ffffffff80209039>] default_idle+0x29/0x40
[ 237.354180] [<ffffffff802090c0>] cpu_idle+0x70/0xc0
[ 237.354195]
[ 237.354197] handlers:
[ 237.354200] [<ffffffff88025d30>] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 237.354222] Disabling IRQ #7
[ 247.623262] bcm43xx: IRQ_READY timeout
[ 304.684015] bcm43xx: IRQ_READY timeout
[ 308.436282] bcm43xx: IRQ_READY timeout
[ 312.089647] bcm43xx: IRQ_READY timeout
[ 318.220590] bcm43xx: IRQ_READY timeout
[ 318.305291] bcm43xx: IRQ_READY timeout
[ 318.413182] bcm43xx: IRQ_READY timeout
[ 318.497617] bcm43xx: IRQ_READY timeout
[ 321.829784] bcm43xx: IRQ_READY timeout
[ 345.149841] bcm43xx: IRQ_READY timeout
[ 351.502147] bcm43xx: IRQ_READY timeout
[ 388.964913] bcm43xx: IRQ_READY timeout
[ 389.049217] bcm43xx: IRQ_READY timeout
[ 423.497350] bcm43xx: IRQ_READY timeout
[ 517.359391] bcm43xx: IRQ_READY timeout
[ 520.821561] bcm43xx: IRQ_READY timeout
[ 524.334735] bcm43xx: IRQ_READY timeout
[ 527.901406] bcm43xx: IRQ_READY timeout
[ 531.317917] bcm43xx: IRQ_READY timeout
[ 534.724690] bcm43xx: IRQ_READY timeout
[ 538.382349] bcm43xx: IRQ_READY timeout
[ 542.068389] bcm43xx: IRQ_READY timeout
[ 544.955323] eth0: no IPv6 routers present
[ 545.806632] bcm43xx: IRQ_READY timeout
[ 549.543077] bcm43xx: IRQ_READY timeout
[ 553.332677] bcm43xx: IRQ_READY timeout
[ 557.139160] bcm43xx: IRQ_READY timeout
[ 560.581256] bcm43xx: IRQ_READY timeout
[ 563.998291] bcm43xx: IRQ_READY timeout
[ 567.786092] bcm43xx: IRQ_READY timeout
[ 571.637243] bcm43xx: IRQ_READY timeout
[ 574.160655] eth0: no IPv6 routers present
[ 575.377821] bcm43xx: IRQ_READY timeout
[ 579.272445] bcm43xx: IRQ_READY timeout
[ 583.111726] bcm43xx: IRQ_READY timeout
[ 586.967981] bcm43xx: IRQ_READY timeout
[ 590.722638] bcm43xx: IRQ_READY timeout
[ 594.395353] bcm43xx: IRQ_READY timeout
[ 617.481014] eth0: link down.
[ 617.795616] bcm43xx: IRQ_READY timeout
[ 636.244012] bcm43xx: IRQ_READY timeout
[ 636.332674] bcm43xx: IRQ_READY timeout
[ 637.621823] bcm43xx: IRQ_READY timeout
[ 659.460026] bcm43xx: IRQ_READY timeout
[ 696.360930] bcm43xx: IRQ_READY timeout
[ 699.868884] bcm43xx: IRQ_READY timeout
[ 703.413357] bcm43xx: IRQ_READY timeout
[ 707.214934] bcm43xx: IRQ_READY timeout
[ 707.299825] bcm43xx: IRQ_READY timeout
[ 707.392429] bcm43xx: IRQ_READY timeout
[ 707.476087] bcm43xx: IRQ_READY timeout
[ 710.799174] bcm43xx: IRQ_READY timeout
[ 714.295589] bcm43xx: IRQ_READY timeout
[ 755.781659] bcm43xx: IRQ_READY timeout
[ 759.697244] bcm43xx: IRQ_READY timeout
[ 763.003977] bcm43xx: IRQ_READY timeout
[ 766.440916] bcm43xx: IRQ_READY timeout
[ 776.243154] nm-applet[5686]: segfault at ffffffffac01b930 rip 00002b55d7873f18 rsp 00007fffd554c160 error 4
[ 789.870995] bcm43xx: IRQ_READY timeout
[ 882.208182] eth0: link up.
[ 913.525047] bcm43xx: IRQ_READY timeout
[ 932.421044] bcm43xx: IRQ_READY timeout
[ 1037.326077] bcm43xx: IRQ_READY timeout
[ 1038.084092] ieee80211_crypt: unregistered algorithm 'NULL'
[ 1043.376895] ieee80211_crypt: registered algorithm 'NULL'
[ 1043.379700] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 1043.379707] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 1043.385631] bcm43xx driver
[ 1043.386401] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 1043.386420] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 1045.192557] bcm43xx: Cannot register IRQ0
[ 1048.943880] Trying to free already-free IRQ 0
[ 1049.020121] bcm43xx: IRQ_READY timeout
[ 1072.853141] bcm43xx: IRQ_READY timeout
[ 1075.312556] ieee80211_crypt: unregistered algorithm 'NULL'
[ 1078.511567] ieee80211_crypt: registered algorithm 'NULL'
[ 1078.513893] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 1078.513901] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 1078.518985] bcm43xx driver
[ 1078.519140] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 1078.519153] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 1079.351065] bcm43xx: Cannot register IRQ0
[ 1083.264592] Trying to free already-free IRQ 0
[ 1083.343262] bcm43xx: IRQ_READY timeout
[ 1107.340272] bcm43xx: IRQ_READY timeout
[ 1130.944584] bcm43xx: IRQ_READY timeout
[ 1154.786871] bcm43xx: IRQ_READY timeout
[ 1171.389601] bcm43xx: IRQ_READY timeout
[ 1278.691429] bcm43xx: IRQ_READY timeout
[ 1402.334904] bcm43xx: IRQ_READY timeout
[ 1526.147007] bcm43xx: IRQ_READY timeout
[ 1552.334821] bcm43xx: IRQ_READY timeout
[ 1626.841481] ieee80211_crypt: unregistered algorithm 'NULL'
[ 1635.405406] ieee80211_crypt: registered algorithm 'NULL'
[ 1635.408254] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 1635.408261] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 1635.413894] bcm43xx driver
[ 1635.414055] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 1635.414067] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 1635.720962] bcm43xx: Cannot register IRQ0
[ 1639.475416] Trying to free already-free IRQ 0
[ 1639.552107] bcm43xx: IRQ_READY timeout
[ 1663.444023] bcm43xx: IRQ_READY timeout
[ 1687.190302] bcm43xx: IRQ_READY timeout
[ 1710.797139] bcm43xx: IRQ_READY timeout
[ 1716.796626] spurious 8259A interrupt: IRQ15.
[ 1734.486321] bcm43xx: IRQ_READY timeout
[ 1756.308601] bcm43xx: IRQ_READY timeout
[ 1758.420656] bcm43xx: IRQ_READY timeout
[ 1814.742072] bcm43xx: IRQ_READY timeout
[ 1818.275326] bcm43xx: IRQ_READY timeout
[ 1842.083173] bcm43xx: IRQ_READY timeout
[ 1865.523906] bcm43xx: IRQ_READY timeout
[ 1889.308290] bcm43xx: IRQ_READY timeout
[ 1912.921413] bcm43xx: IRQ_READY timeout
[ 1936.923158] bcm43xx: IRQ_READY timeout
[ 2016.268939] bcm43xx: IRQ_READY timeout
[ 2060.553545] bcm43xx: IRQ_READY timeout