rendered paste bodyLinux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-18etch1) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Feb 10 22:11:31 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
512MB LOWMEM available.
On node 0 totalpages: 131072
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126976 pages, LIFO batch:31
DMI not present or invalid.
ACPI: RSDP (v000 QEMU ) @ 0x000e8000
ACPI: RSDT (v000 QEMU QEMURSDT 0x00000001 QEMU 0x00000001) @ 0x000e8028
ACPI: FADT (v000 QEMU QEMUFACP 0x00000001 QEMU 0x00000001) @ 0x000e8054
ACPI: MADT (v000 QEMU QEMUAPIC 0x00000001 QEMU 0x00000001) @ 0x000e8978
ACPI: DSDT (v001 QEMU QEMUDSDT 0x00000001 INTL 0x20060421) @ 0x00000000
ACPI: PM-Timer IO Port: 0xb008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:3 APIC version 17
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: IRQ11 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dffc0000)
Detected 1995.536 MHz processor.
Built 1 zonelists. Total pages: 131072
Kernel command line: root=/dev/mapper/debianGanglia-root ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511668k/524288k available (1541k kernel code, 12052k reserved, 580k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 8051.35 BogoMIPS (lpj=16102705)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0781abfd 00000000 00000000 00000000 00000009 00000000 00000000
CPU: After vendor identify, caps: 0781abfd 00000000 00000000 00000000 00000009 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 8K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0781abfd 00000000 00000000 00000040 00000009 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: Intel Pentium II (Klamath) stepping 03
Total of 1 processors activated (8051.35 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4869k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf9fa0, last bus=0
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
* Found PM-Timer Bug on the chipset. Due to workarounds for a bug,
* this clock source is slow. Consider trying other clock sources
PCI quirk: region b000-b03f claimed by PIIX4 ACPI
Boot video device is 0000:00:02.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 6 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: BIOS reporting unknown device 01:00
PCI: BIOS reporting unknown device 01:00
PCI: BIOS reporting unknown device 01:00
PCI: BIOS reporting unknown device 01:00
PCI: BIOS reporting unknown device 01:00
PCI: BIOS reporting unknown device 01:00
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 32768)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1205855252.904:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16450
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16450
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
PM-Timer running at invalid rate: 180% of normal - aborting.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: (supports S5)
Freeing unused kernel memory: 196k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 0000:00:01.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
hda: QEMU HARDDISK, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QEMU CD-ROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL-8029 found at 0xc100, IRQ 10, 52:54:00:12:34:56.
hda: max request size: 512KiB
hda: 4194304 sectors (2147 MB) w/256KiB Cache, CHS=4161/255/63, (U)DMA
hda: set_multmode: status=0x41 { DriveReady Error }
hda: set_multmode: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xef
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdc: ATAPI 4X CD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
piix4_smbus 0000:00:01.3: Found 0000:00:01.3 device
piix4_smbus 0000:00:01.3: SMB base address uninitialized - upgrade BIOS or use force_addr=0xaddr
input: PC Speaker as /class/input/input1
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
FDC 0 is a S82078B
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
ts: Compaq touchscreen protocol output
EXT3 FS on dm-0, internal journal
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 131064k swap on /dev/mapper/debianGanglia-swap_1. Priority:-1 extents:1 across:131064k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
TSC appears to be running slowly. Marking it as unstable
Time: pit clocksource has been installed.
====== var/log/boot
Tue Mar 18 11:48:04 2008: .
Tue Mar 18 11:48:04 2008: Checking root file system...fsck 1.40-WIP (14-Nov-2006)
Tue Mar 18 11:48:04 2008: /dev/mapper/debianGanglia-root: clean, 39055/183872 files, 201414/402432 blocks
Tue Mar 18 11:48:04 2008: done.
Tue Mar 18 11:48:04 2008: Setting the system clock..
Tue Mar 18 11:48:08 2008: Cleaning up ifupdown....
Tue Mar 18 11:48:08 2008: Loading kernel modules...done.
Tue Mar 18 11:48:09 2008: Loading device-mapper support.
Tue Mar 18 11:48:10 2008: Setting up LVM Volume Groups...
Tue Mar 18 11:48:10 2008: Reading all physical volumes. This may take a while...
Tue Mar 18 11:48:10 2008: Found volume group "debianGanglia" using metadata type lvm2
Tue Mar 18 11:48:11 2008: 3 logical volume(s) in volume group "debianGanglia" now active
Tue Mar 18 11:48:11 2008: Checking file systems...fsck 1.40-WIP (14-Nov-2006)
Tue Mar 18 11:48:11 2008: /dev/hda1: clean, 27/62248 files, 21111/248976 blocks
Tue Mar 18 11:48:11 2008: /dev/mapper/debianGanglia-home: clean, 11/25688 files, 8914/102400 blocks
Tue Mar 18 11:48:11 2008: done.
Tue Mar 18 11:48:12 2008: Setting kernel variables...done.
Tue Mar 18 11:48:12 2008: Mounting local filesystems...done.
Tue Mar 18 11:48:13 2008: Activating swapfile swap...done.
Tue Mar 18 11:48:14 2008: Setting up networking....
Tue Mar 18 11:48:15 2008: Configuring network interfaces...done.
Tue Mar 18 11:48:15 2008: Starting portmap daemon....
Tue Mar 18 11:48:18 2008: Setting console screen modes and fonts.
Tue Mar 18 11:48:18 2008: INIT: Entering runlevel: 2
Tue Mar 18 11:48:24 2008: Starting system log daemon: syslogd.
Tue Mar 18 11:48:25 2008: Starting kernel log daemon: klogd.
Tue Mar 18 11:48:25 2008: Starting portmap daemon...Already running..
Tue Mar 18 11:48:27 2008: Loading ACPI modules:
Tue Mar 18 11:48:27 2008: battery
Tue Mar 18 11:48:27 2008: ac
Tue Mar 18 11:48:27 2008: processor
Tue Mar 18 11:48:27 2008: button
Tue Mar 18 11:48:27 2008: fan
Tue Mar 18 11:48:28 2008: thermal
Tue Mar 18 11:48:28 2008: Starting Advanced Configuration and Power Interface daemon: acpid.
Tue Mar 18 11:48:28 2008: Starting MTA: exim4.
Tue Mar 18 11:48:30 2008: Starting Ganglia Monitor Daemon: gmond.
Tue Mar 18 11:48:31 2008: Starting internet superserver: inetd.
Tue Mar 18 11:48:32 2008: Starting OpenBSD Secure Shell server: sshd.
Tue Mar 18 11:48:33 2008: Starting NFS common utilities: statd.
Tue Mar 18 11:48:34 2008: Starting deferred execution scheduler: atd.
Tue Mar 18 11:48:34 2008: Starting periodic command scheduler: crond.
Tue Mar 18 11:48:35 2008: directory entry does exist: /PARAMETERS.TXT ,this is first run
Tue Mar 18 11:48:35 2008:
Tue Mar 18 11:48:35 2008: Starting configuration of ganglia...
Tue Mar 18 11:48:35 2008: Got ip address:10.0.2.15
Tue Mar 18 11:48:35 2008: Reading parameters from file...
Tue Mar 18 11:48:35 2008: This is master node (Node type is:1)
Tue Mar 18 11:48:35 2008: Installing persistence...
Tue Mar 18 11:48:35 2008: Starting database server: couchdb.
Tue Mar 18 11:48:38 2008: Adding system startup for /etc/init.d/couchdb ...
Tue Mar 18 11:48:38 2008: /etc/rc0.d/K20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc1.d/K20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc6.d/K20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc2.d/S20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc3.d/S20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc4.d/S20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: /etc/rc5.d/S20couchdb -> ../init.d/couchdb
Tue Mar 18 11:48:38 2008: Registered startup script and service for couchdb ...
Tue Mar 18 11:48:38 2008: Stopping Ganglia Monitor Daemon: gmond.
Tue Mar 18 11:48:39 2008: Starting Ganglia Monitor Daemon: gmond.
Tue Mar 18 11:48:39 2008: Starting Ganglia Monitor Meta-Daemon: gmetad.
Tue Mar 18 11:48:40 2008: Adding system startup for /etc/init.d/gmetad ...
Tue Mar 18 11:48:40 2008: /etc/rc0.d/K20gmetad -> ../init.d/gmetad
Tue Mar 18 11:48:40 2008: /etc/rc1.d/K20gmetad -> ../init.d/gmetad
Tue Mar 18 11:48:40 2008: /etc/rc6.d/K20gmetad -> ../init.d/gmetad
Tue Mar 18 11:48:40 2008: /etc/rc2.d/S99gmetad -> ../init.d/gmetad
Tue Mar 18 11:48:40 2008: Finishing configuration of node...
Tue Mar 18 11:48:42 2008: