rendered paste bodysmartctl --all /dev/sda
-----------------------
smartctl version 5.37 [i386-redhat-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda ATA V family
Device Model: ST3120023A
Serial Number: 3KA15LH1
Firmware Version: 3.30
User Capacity: 120.033.041.920 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Sun Mar 16 18:00:39 2008 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 426) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 066 055 006 Pre-fail Always - 29360504
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 334
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 085 060 030 Pre-fail Always - 369190769
9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 16142
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1648
194 Temperature_Celsius 0x0022 052 061 000 Old_age Always - 52
195 Hardware_ECC_Recovered 0x001a 066 055 000 Old_age Always - 29360504
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 175 000 Old_age Always - 56
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 87 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 87 occurred at disk power-on lifetime: 6106 hours (254 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 8c 30 75 eb Error: UNC at LBA = 0x0b75308c = 192229516
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 8b 30 75 eb 00 00:01:51.567 READ DMA
c8 00 48 83 30 75 eb 00 00:01:48.015 READ DMA
c8 00 50 7b 30 75 eb 00 00:01:44.447 READ DMA
c8 00 58 73 30 75 eb 00 00:01:40.844 READ DMA
c8 00 60 6b 30 75 eb 00 00:01:37.269 READ DMA
Error 86 occurred at disk power-on lifetime: 6106 hours (254 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 8c 30 75 eb Error: UNC at LBA = 0x0b75308c = 192229516
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 48 83 30 75 eb 00 00:01:48.015 READ DMA
c8 00 50 7b 30 75 eb 00 00:01:44.447 READ DMA
c8 00 58 73 30 75 eb 00 00:01:40.844 READ DMA
c8 00 60 6b 30 75 eb 00 00:01:37.269 READ DMA
c8 00 68 63 30 75 eb 00 00:01:33.718 READ DMA
Error 85 occurred at disk power-on lifetime: 6106 hours (254 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 8c 30 75 eb Error: UNC at LBA = 0x0b75308c = 192229516
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 50 7b 30 75 eb 00 00:01:44.447 READ DMA
c8 00 58 73 30 75 eb 00 00:01:40.844 READ DMA
c8 00 60 6b 30 75 eb 00 00:01:37.269 READ DMA
c8 00 68 63 30 75 eb 00 00:01:33.718 READ DMA
c8 00 70 5b 30 75 eb 00 00:01:30.130 READ DMA
Error 84 occurred at disk power-on lifetime: 6106 hours (254 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 8c 30 75 eb Error: UNC at LBA = 0x0b75308c = 192229516
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 58 73 30 75 eb 00 00:01:40.844 READ DMA
c8 00 60 6b 30 75 eb 00 00:01:37.269 READ DMA
c8 00 68 63 30 75 eb 00 00:01:33.718 READ DMA
c8 00 70 5b 30 75 eb 00 00:01:30.130 READ DMA
c8 00 78 53 30 75 eb 00 00:01:26.533 READ DMA
Error 83 occurred at disk power-on lifetime: 6106 hours (254 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 8c 30 75 eb Error: UNC at LBA = 0x0b75308c = 192229516
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 60 6b 30 75 eb 00 00:01:37.269 READ DMA
c8 00 68 63 30 75 eb 00 00:01:33.718 READ DMA
c8 00 70 5b 30 75 eb 00 00:01:30.130 READ DMA
c8 00 78 53 30 75 eb 00 00:01:26.533 READ DMA
c8 00 80 4b 30 75 eb 00 00:01:22.971 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5622 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.