[trixbox1.localdomain ~]# ztcfg -vv
Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================
Channel map:
0 channels to configure.
[trixbox1.localdomain ~]# wanrouter start
Error: Device wanpipe1 is already running
Run 'wanrouter stop wanpipe1' first
Configuring interfaces: w1g1 w1g1: unknown interface: No such device
done.
[trixbox1.localdomain ~]# ztcfg -vvv
Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================
Channel map:
0 channels to configure.
[trixbox1.localdomain ~]# amportal start
SETTING FILE PERMISSIONS
Permissions OK
STARTING ASTERISK
Asterisk is already running
STARTING FOP SERVER
FOP server is already running
[trixbox1.localdomain ~]# setup-sangoma
#############################################i##########################
# Sangoma Wanpipe: Zaptel/SMG/TDMAPI/BOOT Configuration Script #
# v2.10 #
# Sangoma Technologies Inc. #
# Copyright(c) 2007. #
########################################################################
Generating configuration files for Trixbox
---------------------------------------------
Configuring T1/E1 cards [A101/A102/A104/A108]
---------------------------------------------
------------------------------------
Configuring ISDN BRI cards [A500]
------------------------------------
No Sangoma ISDN BRI cards detected
Press any key to continue:
------------------------------------
Configuring analog cards [A200/A400]
------------------------------------
-----------------------------------------------------------
A200 detected on slot:6 bus:2
-----------------------------------------------------------
Which codec will be used?
1. MULAW - North America
2. ALAW - Europe
[1-2]:1
A200 configured on slot:6 bus:2 span:1
Press any key to continue:
Analog card configuration complete
Press any key to continue:
###################################################################
# SUMMARY #
###################################################################
0 T1/E1 port(s) detected, 0 configured
0 ISDN BRI port(s) detected, 0 configured
1 analog card(s) detected, 1 configured
Configurator has created the following files:
1. Wanpipe config files in /etc/wanpipe
2. Zaptel config file /etc/zaptel.conf
3. Zapata config file /etc/asterisk/zapata-auto.conf
Your original configuration files will be saved to:
1. /etc/zaptel.conf.bak
2. /etc/asterisk/zapata-auto.conf.bak
Your configuration has been saved in /etc/wanpipe/debug-2008-03-03.tgz.
When requesting support, email this file to techdesk@sangoma.com
Press any key to continue:
Zaptel and Wanpipe configuration complete: choose action
1. Save cfg: Restart Asterisk & Wanpipe now
2. Save cfg: Restart Asterisk & Wanpipe when convenient
3. Save cfg: Stop Asterisk & Wanpipe now
4. Save cfg: Stop Asterisk & Wanpipe when convenient
5. Do not save cfg: Exit
[1-5]:1
STOPPING ASTERISK
Disconnected from Asterisk server
Asterisk Stopped
STOPPING FOP SERVER
FOP Server Stopped
FATAL: Module zaptel is in use.
Error executing command:
modprobe -r zaptel
Would you like to continue?
1. No - exit
2. YES
[1-2, ENTER='No']:2
Stopping Wanpipe...
Shutting down wanpipe1 interface: w1g1
w1g1: unknown interface: No such device
Shutting down device: wanpipe1
No devices running, Unloading Modules
Unloading Zaptel modules...
Removing old configuration files...
Copying new Wanpipe configuration files...
Copying new Zaptel configuration file (/etc/zaptel.conf)...
Copying new chan_zap configuration files (/etc/asterisk/zapata-auto.conf)...
Starting Wanpipe...
Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
Configuring interfaces: w1g1 w1g1: unknown interface: No such device
done.
Loading Zaptel...
Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================
0 channels to configure.
Starting Amportal...
SETTING FILE PERMISSIONS
Permissions OK
STARTING ASTERISK
Asterisk Started
STARTING FOP SERVER
FOP Server Started
Wanrouter start complete...
Current boot level is 3
Wanrouter boot scripts configuration...
Removing existing wanrouter boot scripts...OK
Would you like wanrouter to start on system boot?
1. YES
2. NO
[1-2]:1
Verifying Zaptel boot scripts...Enabled (level:09)
Verifying Zaptel shutdown scripts...Enabled (level:92)
Enabling wanrouter boot scripts ...(level:8)
Enabling wanrouter shutdown scripts ...(level:91)
Sangoma cards configuration complete, exiting...