rendered paste bodyLinux version 2.6.21.5-smp (root@midas) (gcc version 4.1.2) #2 SMP Tue Jun 19 14:58:11 CDT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 00000000bbea0000 end: 00000000bbfa0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 00000000bbfa0000 size: 000000000000e000 end: 00000000bbfae000 type: 3
copy_e820_map() start: 00000000bbfae000 size: 0000000000032000 end: 00000000bbfe0000 type: 4
copy_e820_map() start: 00000000bbfe0000 size: 000000000000e000 end: 00000000bbfee000 type: 2
copy_e820_map() start: 00000000bbff0000 size: 0000000000010000 end: 00000000bc000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000fff00000 size: 0000000000100000 end: 0000000100000000 type: 2
copy_e820_map() start: 0000000100000000 size: 0000000040000000 end: 0000000140000000 type: 1
copy_e820_map() type is E820_RAM
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bbfa0000 (usable)
BIOS-e820: 00000000bbfa0000 - 00000000bbfae000 (ACPI data)
BIOS-e820: 00000000bbfae000 - 00000000bbfe0000 (ACPI NVS)
BIOS-e820: 00000000bbfe0000 - 00000000bbfee000 (reserved)
BIOS-e820: 00000000bbff0000 - 00000000bc000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
Warning only 4GB will be used.
Use a PAE enabled kernel.
3200MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 1048576
early_node_map[1] active PFN ranges
0: 0 -> 1048576
On node 0 totalpages: 1048576
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 6400 pages used for memmap
HighMem zone: 812800 pages, LIFO batch:31
DMI present.
ACPI: RSDP 000F9870, 0014 (r0 ACPIAM)
ACPI: RSDT BBFA0000, 003C (r1 110707 RSDT0930 20071107 MSFT 97)
ACPI: FACP BBFA0200, 0084 (r1 110707 FACP0930 20071107 MSFT 97)
ACPI Warning (tbfadt-0360): Ignoring BIOS FADT r1 C-state control [20070126]
ACPI: DSDT BBFA04A0, 4AF0 (r1 1ADSY 1ADSY002 2 INTL 20051117)
ACPI: FACS BBFAE000, 0040
ACPI: APIC BBFA0390, 0080 (r1 110707 APIC0930 20071107 MSFT 97)
ACPI: MCFG BBFA0410, 003C (r1 110707 OEMMCFG 20071107 MSFT 97)
ACPI: WDRT BBFA0450, 0047 (r1 110707 NV-WDRT 20071107 MSFT 97)
ACPI: OEMB BBFAE040, 0071 (r1 110707 OEMB0930 20071107 MSFT 97)
ACPI: SSDT BBFAF300, 0A7C (r1 DpgPmm CpuPm 12 INTL 20051117)
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 6:15 APIC version 20
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c0000000 (gap: bc000000:42c00000)
Built 1 zonelists. Total pages: 1040384
Kernel command line: auto BOOT_IMAGE=Linux ro root=801
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2400.100 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3035632k/4194304k available (6215k kernel code, 43016k reserved, 2017k data, 392k init, 2162304k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0915000 - 0xc0977000 ( 392 kB)
.data : 0xc0711c79 - 0xc090a38c (2017 kB)
.text : 0xc0100000 - 0xc0711c79 (6215 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4805.03 BogoMIPS (lpj=9610079)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 24k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.25 BogoMIPS (lpj=9600517)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b
Booting processor 2/2 eip 2000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4800.31 BogoMIPS (lpj=9600639)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b
Booting processor 3/3 eip 2000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4800.29 BogoMIPS (lpj=9600598)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU: After all inits, caps: bfebfbff 20000000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b
Total of 4 processors activated (19205.91 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
migration_cost=66,5197
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:10.0
PCI: Transparent bridge - 0000:00:0a.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
libata version 2.20 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:05: iomem range 0x0-0x0 could not be reserved
pnp: 00:05: iomem range 0xfed02000-0xfed03fff has been reserved
pnp: 00:05: iomem range 0xfed04000-0xfed04fff has been reserved
pnp: 00:05: iomem range 0xfee01000-0xfeefffff has been reserved
pnp: 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0a: ioport range 0xa00-0xadf has been reserved
pnp: 00:0a: ioport range 0xae0-0xaef has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0c: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0c: iomem range 0x100000-0xbfffffff could not be reserved
ieee1394: Initialized config rom entry `ip1394'
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:0a.0
IO window: d000-dfff
MEM window: fea00000-feafffff
PREFETCH window: c0000000-c00fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: e000-efff
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0a.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.28 [Flags: R/W].
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Jun 19 2007 14:57:33) installed
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xd0000000, mapped to 0xf8d00000, using 1536k, total 65536k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:c380
vesafb: pmi: set display start = c00cc3b6, set palette = c00cc420
vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 0
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
JMB363: IDE controller at PCI slot 0000:03:00.1
PCI: Enabling device 0000:03:00.1 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
ACPI: PCI Interrupt 0000:03:00.1[B] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 16
JMB363: chipset revision 3
JMB363: 100% native mode on irq 16
PCI: Setting latency timer of device 0000:03:00.1 to 64
ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG CD-R/RW SW-240B, ATAPI CD/DVD-ROM drive
hdb: JLMS DVD-ROM LTD-166S, ATAPI CD/DVD-ROM drive
ide0 at 0xec00-0xec07,0xe882 on irq 16
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (tcp)
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver (1.1-5[2423]-mh3)
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.1.11
Copyright(c) 2004-2006 Emulex. All rights reserved.
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.3.1 (January 23, 2007)
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
st: Version 20070203, fixed bufsize 32768, s/g segs 256
ahci 0000:03:00.0: version 2.1
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNEA] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.0 to 64
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ata1: SATA max UDMA/133 cmd 0xf8cec100 ctl 0x00000000 bmdma 0x00000000 irq 17
ata2: SATA max UDMA/133 cmd 0xf8cec180 ctl 0x00000000 bmdma 0x00000000 irq 17
scsi2 : ahci
ata1: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata2: SATA link down (SStatus 0 SControl 300)
sata_nv 0000:00:0e.0: version 3.3
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata3: SATA max UDMA/133 cmd 0x0001c480 ctl 0x0001c402 bmdma 0x0001bc00 irq 18
ata4: SATA max UDMA/133 cmd 0x0001c080 ctl 0x0001c002 bmdma 0x0001bc08 irq 18
scsi4 : sata_nv
ata3: SATA link up <unknown> (SStatus A3229F03 SControl 0)
ata3.00: ATA-6: WDC WD800JB-00ETA0, 77.07W77, max UDMA/100
ata3.00: 156301488 sectors, multi 16: LBA48
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
scsi5 : sata_nv
ata4: SATA link down (SStatus 0 SControl 0)
scsi 4:0:0:0: Direct-Access ATA WDC WD800JB-00ET 77.0 PQ: 0 ANSI: 5
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 4:0:0:0: Attached scsi disk sda
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
Fusion MPT FC Host driver 3.04.04
Fusion MPT SAS Host driver 3.04.04
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 19, io mem 0xfe97ec00
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LUB0] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 20, io mem 0xfe97f000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 948 MB/s
raid6: int32x2 947 MB/s
raid6: int32x4 752 MB/s
raid6: int32x8 701 MB/s
raid6: mmxx1 3085 MB/s
raid6: mmxx2 3557 MB/s
raid6: sse1x1 2078 MB/s
input: AT Translated Set 2 keyboard as /class/input/input1
raid6: sse1x2 2727 MB/s
raid6: sse2x1 3746 MB/s
raid6: sse2x2 4346 MB/s
raid6: using algorithm sse2x2 (4346 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 9053.000 MB/sec
raid5: using function: pIII_sse (9053.000 MB/sec)
md: multipath personality registered for level -4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 392k freed
kobject_add failed for ehci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
=======================
kobject_add failed for ohci_hcd with -EEXIST, don't try to register things with the same name in the same directory.
[<c03e86f7>] kobject_shadow_add+0x117/0x1a0
[<c013fba4>] mod_sysfs_setup+0x24/0xb0
[<c0141458>] sys_init_module+0x1648/0x1940
[<c0102ae8>] syscall_call+0x7/0xb
[<c0710000>] __mutex_lock_slowpath+0x40/0x90
=======================
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
sd 4:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKA] -> GSI 17 (level, low) -> IRQ 21
skge 1.10 addr 0xfeafc000 irq 21 chip Yukon-Lite rev 9
skge eth0: addr 00:1c:f0:0f:4a:da
Adding 8008392k swap on /dev/sda3. Priority:-1 extents:1 across:8008392k
input: PC Speaker as /class/input/input2
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
lp: driver loaded but no devices found
Linux agpgart interface v0.102 (c) Dave Jones
Capability LSM initialized
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
skge eth0: enabling interface
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
skge eth0: Link is up at 10 Mbps, half duplex, flow control none
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present