rendered paste bodyastriskserver*CLI> zap show channels
Chan Extension Context Language MOH Interpret
pseudo default default
cts@astriskserver:~/backup_asterisk$ sudo ztcfg -vvvv
Zaptel Version: 1.4.8
Echo Canceller: MG2
Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
4 channels to configure.
astriskserver*CLI> zap show status
Description Alarms IRQ bpviol CRC4
Wildcard TDM400P REV I Board 1 OK 0 0 0
astriskserver*CLI> load chan_zap.so
The 'load' command is deprecated and will be removed in a future release. Please use 'module load' instead.
[Feb 11 18:44:19] WARNING[17965]: loader.c:639 load_resource: Module 'chan_zap.so' already exists.
/etc/zaptel.conf
fxsks = 1-4
loadzone = us
defaultzone = us
/etc/asterisk/zapata.conf
[channels]
language=en
context=demo
signalling=fxs_ks
usecallerid=yes
hidecallerid=no
callwaiting=no
callwaitingcallerid=no
threewaycalling=no
transfer=yes
callreturn=yes
group=1
channel => 1
channel => 2
channel => 3
channel => 4
cts@astriskserver:~/backup_asterisk$ cat /proc/zaptel/*
Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" (MASTER)
1 WCTDM/0/0 FXSKS
2 WCTDM/0/1 FXSKS
3 WCTDM/0/2 FXSKS
4 WCTDM/0/3 FXSKS
cts@astriskserver:~/backup_asterisk$ dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Fri Feb 1 04:59:50 UTC 2008 (Ubuntu 2.6.22-14.51-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000bef0000 (usable)
[ 0.000000] BIOS-e820: 000000000bef0000 - 000000000bef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000000bef3000 - 000000000bf00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 190MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 48880) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 48880
[ 0.000000] HighMem 48880 -> 48880
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 48880
[ 0.000000] On node 0 totalpages: 48880
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 349 pages used for memmap
[ 0.000000] Normal zone: 44435 pages, LIFO batch:7
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F7A60 checksum 0
[ 0.000000] ACPI: RSDP 000F7A60, 0014 (r0 IntelR)
[ 0.000000] ACPI: RSDT 0BEF3000, 0028 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 0BEF3040, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 0BEF30C0, 3872 (r1 INTELR AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 0BEF0000, 0040
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: 0bf00000:f3c00000)
[ 0.000000] Built 1 zonelists. Total pages: 48499
[ 0.000000] Kernel command line: root=UUID=6f446461-0746-4066-b536-61ba4266c8f4 ro quiet splash
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffd000 (0118c000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 803.434 MHz processor.
[ 28.434645] Console: colour VGA+ 80x25
[ 28.435315] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 28.435922] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 28.458947] Memory: 182316k/195520k available (2015k kernel code, 12668k reserved, 916k data, 364k init, 0k highmem)
[ 28.458975] virtual kernel memory layout:
[ 28.458978] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 28.458982] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 28.458986] vmalloc : 0xcc800000 - 0xff7fe000 ( 815 MB)
[ 28.458989] lowmem : 0xc0000000 - 0xcbef0000 ( 190 MB)
[ 28.458993] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 28.458996] .data : 0xc02f7e66 - 0xc03dce84 ( 916 kB)
[ 28.459000] .text : 0xc0100000 - 0xc02f7e66 (2015 kB)
[ 28.459010] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 28.459113] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 28.539114] Calibrating delay using timer specific routine.. 1608.27 BogoMIPS (lpj=3216544)
[ 28.539177] Security Framework v1.0.0 initialized
[ 28.539197] SELinux: Disabled at boot.
[ 28.539233] Mount-cache hash table entries: 512
[ 28.539523] CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 28.539550] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 28.539557] CPU: L2 cache: 256K
[ 28.539565] CPU serial number disabled.
[ 28.539571] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 28.539595] Compat vDSO mapped to ffffe000.
[ 28.539630] Checking 'hlt' instruction... OK.
[ 28.555380] SMP alternatives: switching to UP code
[ 28.555839] Freeing SMP alternatives: 11k freed
[ 28.556617] Early unpacking initramfs... done
[ 29.425932] ACPI: Core revision 20070126
[ 29.426280] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 29.430562] ACPI: setting ELCR to 0200 (from 1a20)
[ 29.433786] CPU0: Intel Pentium III (Coppermine) stepping 06
[ 29.433806] SMP motherboard not detected.
[ 29.433813] Local APIC not detected. Using dummy APIC emulation.
[ 29.433940] Brought up 1 CPUs
[ 29.434353] Booting paravirtualized kernel on bare hardware
[ 29.434500] Time: 0:23:33 Date: 01/12/108
[ 29.434598] NET: Registered protocol family 16
[ 29.434996] EISA bus registered
[ 29.435032] ACPI: bus type pci registered
[ 29.459040] PCI: PCI BIOS revision 2.10 entry at 0xfb0f0, last bus=1
[ 29.459048] PCI: Using configuration type 1
[ 29.459054] Setting up standard PCI resources
[ 29.466709] ACPI: EC: Look up EC in DSDT
[ 29.475676] ACPI: Interpreter enabled
[ 29.475687] ACPI: (supports S0 S1 S4 S5)
[ 29.475731] ACPI: Using PIC for interrupt routing
[ 29.489143] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 29.489166] PCI: Probing PCI hardware (bus 00)
[ 29.489517] PCI quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
[ 29.489527] PCI quirk: region 4080-40bf claimed by ICH4 GPIO
[ 29.490040] PCI: Transparent bridge - 0000:00:1e.0
[ 29.490089] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 29.490494] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 29.524274] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 29.524543] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 29.524801] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 29.525058] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 29.525314] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 29.525572] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 29.525828] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 29.526086] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
[ 29.526351] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 29.526401] pnp: PnP ACPI init
[ 29.526433] ACPI: bus type pnp registered
[ 29.535392] pnp: PnP ACPI: found 14 devices
[ 29.535405] ACPI: ACPI bus type pnp unregistered
[ 29.535417] PnPBIOS: Disabled by ACPI PNP
[ 29.535593] PCI: Using ACPI for IRQ routing
[ 29.535603] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 29.544307] NET: Registered protocol family 8
[ 29.544314] NET: Registered protocol family 20
[ 29.544543] pnp: 00:00: iomem range 0xcc000-0xcffff has been reserved
[ 29.544552] pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
[ 29.544560] pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[ 29.544568] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 29.546729] Time: tsc clocksource has been installed.
[ 29.575397] PCI: Bridge: 0000:00:1e.0
[ 29.575404] IO window: c000-cfff
[ 29.575416] MEM window: d4000000-d40fffff
[ 29.575423] PREFETCH window: disabled.
[ 29.575446] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 29.575488] NET: Registered protocol family 2
[ 29.614865] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 29.615002] TCP established hash table entries: 8192 (order: 4, 98304 bytes)
[ 29.615413] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 29.615714] TCP: Hash tables configured (established 8192 bind 8192)
[ 29.615723] TCP reno registered
[ 29.627173] checking if image is initramfs...<6>Switched to high resolution mode on CPU 0
[ 30.328797] it is
[ 31.248294] Freeing initrd memory: 7048k freed
[ 31.249372] audit: initializing netlink socket (disabled)
[ 31.249422] audit(1202775814.592:1): initialized
[ 31.255925] VFS: Disk quotas dquot_6.5.1
[ 31.256141] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 31.256512] io scheduler noop registered
[ 31.256520] io scheduler anticipatory registered
[ 31.256525] io scheduler deadline registered
[ 31.256594] io scheduler cfq registered (default)
[ 31.256642] Boot video device is 0000:00:02.0
[ 31.257145] isapnp: Scanning for PnP cards...
[ 31.611084] isapnp: No Plug & Play device found
[ 31.697860] Real Time Clock Driver v1.12ac
[ 31.698113] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 31.698292] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 31.698813] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 31.700425] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 31.701110] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 31.703393] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 31.704014] input: Macintosh mouse button emulation as /class/input/input0
[ 31.704246] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 31.704254] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 31.957971] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 31.958401] mice: PS/2 mouse device common for all mice
[ 31.958712] EISA: Probing bus 0 at eisa.0
[ 31.958746] Cannot allocate resource for EISA slot 4
[ 31.958752] Cannot allocate resource for EISA slot 5
[ 31.958772] EISA: Detected 0 cards.
[ 31.959064] TCP cubic registered
[ 31.959110] NET: Registered protocol family 1
[ 31.959189] Using IPI No-Shortcut mode
[ 31.959632] Magic number: 12:693:354
[ 31.961228] Freeing unused kernel memory: 364k freed
[ 32.037723] input: AT Translated Set 2 keyboard as /class/input/input1
[ 33.620914] AppArmor: AppArmor initialized<5>audit(1202775817.092:2): type=1505 info="AppArmor initialized" pid=1170
[ 33.648176] fuse init (API version 7.8)
[ 33.663684] Failure registering capabilities with primary security module.
[ 33.689083] ACPI: Fan [FAN] (on)
[ 33.705679] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 33.705698] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 33.710459] ACPI: Thermal Zone [THRM] (40 C)
[ 35.674141] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 35.674224] 8139cp 0000:01:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 35.674236] 8139cp 0000:01:02.0: Try the "8139too" driver instead.
[ 35.682153] 8139too Fast Ethernet driver 0.9.28
[ 35.682802] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 35.682812] PCI: setting IRQ 11 as level-triggered
[ 35.682820] ACPI: PCI Interrupt 0000:01:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 35.683319] eth0: RealTek RTL8139 at 0xcc816000, 00:02:44:04:65:c6, IRQ 11
[ 35.683327] eth0: Identified 8139 chip type 'RTL-8139C'
[ 35.807827] SCSI subsystem initialized
[ 35.832931] libata version 2.21 loaded.
[ 35.840523] ata_piix 0000:00:1f.1: version 2.11
[ 35.840699] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 35.841021] scsi0 : ata_piix
[ 35.841151] scsi1 : ata_piix
[ 35.841466] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
[ 35.841477] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
[ 35.881267] usbcore: registered new interface driver usbfs
[ 35.881341] usbcore: registered new interface driver hub
[ 35.881407] usbcore: registered new device driver usb
[ 35.885717] USB Universal Host Controller Interface driver v3.0
[ 36.161892] ata1.00: ATA-7: Hitachi HDS721616PLAT80, P22OA85A, max UDMA/133
[ 36.161907] ata1.00: 321672960 sectors, multi 16: LBA48
[ 36.161932] ata1.01: ATAPI: ATAPI 52X CDROM, VER-1.40, max UDMA/33
[ 36.161949] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 36.162429] Floppy drive(s): fd0 is 1.44M
[ 36.176125] ata1.00: configured for UDMA/33
[ 36.193474] FDC 0 is a post-1991 82077
[ 36.331977] ata1.01: configured for UDMA/33
[ 8.000000] Marking TSC unstable due to: possible TSC halt in C2.
[ 8.012000] Time: acpi_pm clocksource has been installed.
[ 8.036000] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72161 P22O PQ: 0 ANSI: 5
[ 8.036000] scsi 0:0:1:0: CD-ROM ATAPI 52X CDROM 1.40 PQ: 0 ANSI: 5
[ 8.048000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 8.048000] ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 8.048000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 8.048000] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 8.052000] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 8.052000] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000d000
[ 8.052000] usb usb1: configuration #1 chosen from 1 choice
[ 8.052000] hub 1-0:1.0: USB hub found
[ 8.052000] hub 1-0:1.0: 2 ports detected
[ 8.100000] sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
[ 8.100000] sd 0:0:0:0: [sda] Write Protect is off
[ 8.100000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.100000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.100000] sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
[ 8.100000] sd 0:0:0:0: [sda] Write Protect is off
[ 8.100000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.100000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.100000] sda: sda1 sda2 < sda5 >
[ 8.136000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.156000] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
[ 8.156000] ACPI: PCI Interrupt 0000:00:1f.4[C] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
[ 8.156000] PCI: Setting latency timer of device 0000:00:1f.4 to 64
[ 8.156000] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 8.156000] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
[ 8.156000] uhci_hcd 0000:00:1f.4: irq 11, io base 0x0000d400
[ 8.156000] usb usb2: configuration #1 chosen from 1 choice
[ 8.156000] hub 2-0:1.0: USB hub found
[ 8.156000] hub 2-0:1.0: 2 ports detected
[ 8.160000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.160000] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 8.164000] sr0: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
[ 8.164000] Uniform CD-ROM driver Revision: 3.20
[ 8.164000] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 8.396000] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 8.568000] usb 1-1: configuration #1 chosen from 1 choice
[ 8.612000] usbcore: registered new interface driver hiddev
[ 8.632000] input: Dell Dell USB Mouse as /class/input/input2
[ 8.632000] input: USB HID v1.10 Mouse [Dell Dell USB Mouse] on usb-0000:00:1f.2-1
[ 8.632000] usbcore: registered new interface driver usbhid
[ 8.632000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 8.676000] Attempting manual resume
[ 8.676000] swsusp: Resume From Partition 8:5
[ 8.676000] PM: Checking swsusp image.
[ 8.680000] PM: Resume from disk failed.
[ 8.768000] kjournald starting. Commit interval 5 seconds
[ 8.768000] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.336000] iTCO_vendor_support: vendor-support=0
[ 21.348000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[ 21.352000] iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
[ 21.352000] iTCO_wdt: No card detected
[ 21.364000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 21.372000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 21.404000] intel_rng: FWH not detected
[ 21.516000] Linux agpgart interface v0.102 (c) Dave Jones
[ 21.548000] agpgart: Detected an Intel i815 Chipset.
[ 21.568000] agpgart: AGP aperture is 64M @ 0xd0000000
[ 21.584000] i810_smbus 0000:00:02.0: i810/i815 i2c device found.
[ 22.364000] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[ 22.436000] HiSax: Linux Driver for passive ISDN cards
[ 22.436000] HiSax: Version 3.5 (module)
[ 22.436000] HiSax: Layer1 Revision 2.46.2.5
[ 22.436000] HiSax: Layer2 Revision 2.30.2.4
[ 22.436000] HiSax: TeiMgr Revision 2.20.2.3
[ 22.436000] HiSax: Layer3 Revision 2.22.2.3
[ 22.436000] HiSax: LinkLayer Revision 2.59.2.4
[ 22.508000] Zapata Telephony Interface Registered on major 196
[ 22.508000] Zaptel Version: 1.4.8
[ 22.508000] Zaptel Echo Canceller: MG2
[ 22.528000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
[ 22.528000] PCI: setting IRQ 12 as level-triggered
[ 22.528000] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
[ 22.528000] Freshmaker version: 73
[ 22.528000] Freshmaker passed register test
[ 23.224000] Module 0: Installed -- AUTO FXO (FCC mode)
[ 23.424000] Module 1: Installed -- AUTO FXO (FCC mode)
[ 23.624000] Module 2: Installed -- AUTO FXO (FCC mode)
[ 23.824000] Module 3: Installed -- AUTO FXO (FCC mode)
[ 23.828000] Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules)
[ 26.088000] input: PC Speaker as /class/input/input3
[ 26.196000] parport_pc 00:0a: reported by Plug and Play ACPI
[ 26.196000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 26.600000] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[ 26.600000] PCI: setting IRQ 5 as level-triggered
[ 26.600000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 26.600000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 26.924000] intel8x0_measure_ac97_clock: measured 54304 usecs
[ 26.924000] intel8x0: clocking to 48000
[ 27.604000] loop: module loaded
[ 27.648000] lp0: using parport0 (interrupt-driven).
[ 27.876000] Adding 554200k swap on /dev/sda5. Priority:-1 extents:1 across:554200k
[ 28.316000] EXT3 FS on sda1, internal journal
[ 31.000000] No dock devices found.
[ 31.316000] input: Power Button (FF) as /class/input/input4
[ 31.316000] ACPI: Power Button (FF) [PWRF]
[ 31.340000] input: Power Button (CM) as /class/input/input5
[ 31.340000] ACPI: Power Button (CM) [PWRB]
[ 31.356000] input: Sleep Button (CM) as /class/input/input6
[ 31.356000] ACPI: Sleep Button (CM) [SLPB]
[ 34.564000] Registered Tormenta2 PCI
[ 34.920000] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 36.088000] usbcore: registered new interface driver wcusb
[ 36.088000] Wildcard USB FXS Interface driver registered
[ 36.336000] INFO-xpp: revision trunk-r5254 MAX_XPDS=64 (8*8)
[ 36.336000] INFO-xpp: FEATURE: without BRISTUFF support
[ 36.336000] INFO-xpp: FEATURE: with PROTOCOL_DEBUG
[ 36.344000] INFO-xpp: FEATURE: with ECHO_SUPPRESSION
[ 36.344000] INFO-xpp: FEATURE: without XPP_EC_CHUNK
[ 36.344000] INFO-xpp: FEATURE: with sync_tick() from ZAPTEL
[ 36.384000] INFO-xpp_usb: revision trunk-r5254 [sizeof(uframe)=176]
[ 36.436000] usbcore: registered new interface driver xpp_usb
[ 39.484000] Registered tone zone 0 (United States / North America)
[ 39.484000] Registered tone zone 0 (United States / North America)
[ 40.004000] NET: Registered protocol family 10
[ 40.004000] lo: Disabled Privacy Extensions
[ 40.348000] ppdev: user-space parallel port driver
[ 40.588000] audit(1202775853.177:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4944 profile="/usr/sbin/cupsd"
[ 40.688000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 40.688000] apm: overridden by ACPI.
[ 41.432000] Failure registering capabilities with primary security module.
[ 41.844000] Bluetooth: Core ver 2.11
[ 41.848000] NET: Registered protocol family 31
[ 41.848000] Bluetooth: HCI device and connection manager initialized
[ 41.848000] Bluetooth: HCI socket layer initialized
[ 41.888000] Bluetooth: L2CAP ver 2.8
[ 41.888000] Bluetooth: L2CAP socket layer initialized
[ 41.964000] Bluetooth: RFCOMM socket layer initialized
[ 41.964000] Bluetooth: RFCOMM TTY layer initialized
[ 41.964000] Bluetooth: RFCOMM ver 1.8
[ 46.088000] NET: Registered protocol family 17
[ 61.536000] eth0: no IPv6 routers present