rendered paste bodyLinux version 2.6.22 (linuxguy@intrepid) (gcc version 4.1.2) #69 Fri Feb 8 15:19:05 PST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: TCT_HAMMER
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
DMA zone: 64 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 8128 pages, LIFO batch:0
Normal zone: 0 pages used for memmap
CPU S3C2410A (id 0x32410002)
S3C2410: core 202.800 MHz, memory 101.400 MHz, peripheral 50.700 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttySAC0 root=/dev/ram0
irq: clearing subpending status 00000002
PID hash table entries: 128 (order: 7, 512 bytes)
timer tcon=00000000, tcnt a509, tcfg 00000200,00000000, usec 00001e4c
selected clock c01df178 (pclk) quot 27, calc 113169
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 27388KB available (1736K code, 159K data, 92K init)
Calibrating delay loop... 101.17 BogoMIPS (lpj=252928)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410: Initialising architecture
NET: Registered protocol family 23
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 3072K
NetWinder Floating Point Emulator V0.97 (extended precision)
audit: initializing netlink socket (disabled)
audit(2.270:1): initialized
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Non-volatile memory driver v1.2
s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
nbd: registered device at major 43
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
dm9000 Ethernet Driver
physmap platform flash device: 01000000 at 00000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=128
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 2 MTD partitions on "physmap-flash.0":
0x00000000-0x00400000 : "System"
mtd: Giving out device 0 to System
0x00400000-0x01000000 : "JFFS2"
mtd: Giving out device 1 to JFFS2
i2c-core: driver [ds1307] registered
i2c /dev entries driver
i2c-core: driver [dev_driver] registered
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 15
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
RAMDISK: Compressed image found at block 0
length error
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 92K
selected clock c01df178 (pclk) quot 27, calc 113169
selected clock c01df178 (pclk) quot 27, calc 113169
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new full speed USB device using s3c2410-ohci and address 3
usb 1-1.1: no configurations
usb 1-1.1: can't read configurations, error -22
usb 1-1.1: new full speed USB device using s3c2410-ohci and address 4
usb 1-1.1: configuration #1 chosen from 1 choice
usb 1-1.2: new full speed USB device using s3c2410-ohci and address 5
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.3: new full speed USB device using s3c2410-ohci and address 6
usb 1-1.3: configuration #1 chosen from 1 choice
usb 1-1.4: new full speed USB device using s3c2410-ohci and address 7
usb 1-1.4: configuration #1 chosen from 1 choice
usbcore: registered new interface driver libusual
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access PNY USB 2.0 FD PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 4030464 512-byte hardware sectors (2064 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 4030464 512-byte hardware sectors (2064 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
s3c2410_udc: debugfs dir creation failed -19
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk
usb0: MAC 66:f6:39:ae:11:7a
usb0: HOST MAC 26:f5:6d:e0:c8:66
usb0: RNDIS ready
usbcore: registered new interface driver irda-usb
USB IrDA support registered
selected clock c01df178 (pclk) quot 27, calc 113169
selected clock c01df178 (pclk) quot 27, calc 113169
selected clock c01df178 (pclk) quot 27, calc 113169
selected clock c01df178 (pclk) quot 27, calc 113169
#