rendered paste bodyBootcode Ver.1.11 for [HGLAN]
Build:May 17 2005 [14:11:09]
isUseRevClock=0
******* Product Information *******
----------------------------------
Product Name: HD-HGLAN(IEMITSU)
VER: 2.08
Date: 2006/2/9 12:0:6
----------------------------------
Firmware check:done.
>>root=/dev/hda1
hit any key to boot EM mode.
Now Loading...done.
Now Booting
KERNELBASE=c0000000 r6=900030 r7=90003e
cmd_line=root=/dev/hda1
Memory BAT mapping: BAT2=128Mb, BAT3=0Mb, residual: 0Mb
This processor does not support HPTE table
Linux version 2.4.33.3-list.mg.2-v3 (root@LINKSTATION) (gcc version 3.3.5 (Debi6
BUFFALO Network Attached Storage Series
(C) 2002-2005 BUFFALO INC.
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda1
OpenPIC Version 1.2 (1 CPUs and 11 IRQ sources) at 80040000
Bus clock freq: 131072000
decrementer frequency = 32.521743 MHz
Calibrating delay loop... 173.26 BogoMIPS
Memory: 125452k available (1448k kernel code, 500k data, 68k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-algo-8245.o: i2c MPC8245 algorithm module
i2c-mpc8245.o: i2c mpc8245 module
i2c-algo-8245: Using IRQ 21
i2c-mpc8245.o: found device at 0x80003000.
i2c-proc.o version 2.6.1 (20010830)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ed
ttyS00 at 0x80004600 (irq = 26) is a 16550A
ttyS01 at 0x80004500 (irq = 25) is a 16550A
I2C: rs5c372 RTC driver successfully loaded
RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter
eth0: RTL8169s/8110s Gigabit Ethernet driver 2.3 at 0xbfff00, 00:0d:0b:99:3c:7f6
eth0: Auto-negotiation Enabled.
eth0: 1000Mbps Full-duplex operation.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
IT8212: unknown IDE controller at PCI slot 00:0c.0, VID=1283, DID=8212
IT8212: chipset revision 19
IT8212: not 100% native mode: will probe irqs later
it821x: controller in smart mode.
ide0: BM-DMA at 0xbffed0-0xbffed7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xbffed8-0xbffedf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
ide0: Wait for ready failed before probe !
Probing IDE interface ide1...
ide1: Wait for ready failed before probe !
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
LinkStation flash device: 400000 at ffc00000
NO QRY response
Amd/Fujitsu Extended Query Table v1.0 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 5 MTD partitions on "LinkStation Flash":
0x00000000-0x00300000 : "mtd0: kernel+ramdisk"
0x00300000-0x00370000 : "mtd1: bootloader"
0x00370000-0x00380000 : "mtd2: configuration"
0x00380000-0x00400000 : "mtd3: user space"
0x00000000-0x00400000 : "mtd4: all flash"
LinkStation flash device initialized
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:0e.2: PCI device 1033:00e0
ehci_hcd 00:0e.2: irq 19, pci mem bfffcf00
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 5 ports detected
host/usb-ohci.c: USB OHCI at membase 0xbfffe000, IRQ 19
host/usb-ohci.c: usb-00:0e.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
host/usb-ohci.c: USB OHCI at membase 0xbfffd000, IRQ 19
host/usb-ohci.c: usb-00:0e.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2056k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
kmod: failed to exec /sbin/modprobe -s -k block-major-3, errno = 2
VFS: Cannot open root device "hda1" or 03:01
Please append a correct "root=" boot option
Kernel panic: VFS: Unable to mount root fs on 03:01