athlon mnt # smartctl -a /dev/hdd
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus D740X family
Device Model: MAXTOR 6L040J2
Serial Number: 662215842583
Firmware Version: AR1.0500
User Capacity: 40,027,029,504 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1
Local Time is: Fri Jul 14 18:34:39 2006 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 34) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 21) minutes.
SMART Attributes Data Structure revision number: 11
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 082 080 020 Pre-fail Always - 2286
4 Start_Stop_Count 0x0032 093 093 008 Old_age Always - 4805
5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always - 2
7 Seek_Error_Rate 0x000b 100 085 023 Pre-fail Always - 0
9 Power_On_Hours 0x0012 078 078 001 Old_age Always - 14802
10 Spin_Retry_Count 0x0026 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 093 093 008 Old_age Always - 4706
13 Read_Soft_Error_Rate 0x000b 100 093 023 Pre-fail Always - 0
194 Temperature_Celsius 0x0022 087 080 042 Old_age Always - 35
195 Hardware_ECC_Recovered 0x001a 100 013 000 Old_age Always - 5204625
196 Reallocated_Event_Count 0x0010 100 253 020 Old_age Offline - 0
197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 674 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 674 occurred at disk power-on lifetime: 3080 hours (128 days + 8 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 d1 01 6e 5d 7e f0 Error: UNC 1 sectors at LBA = 0x007e5d6e = 8281454
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 6e 5d 7e f0 7e 00:05:25.085 READ DMA
c8 00 02 6d 5d 7e f0 7e 00:05:19.943 READ DMA
c8 00 03 6c 5d 7e f0 7e 00:05:14.801 READ DMA
c8 00 04 6b 5d 7e f0 7e 00:05:09.660 READ DMA
c8 00 05 6a 5d 7e f0 7e 00:05:04.518 READ DMA
Error 673 occurred at disk power-on lifetime: 3080 hours (128 days + 8 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 6e 5d 7e f0 Error: UNC 1 sectors at LBA = 0x007e5d6e = 8281454
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 6d 5d 7e f0 7e 00:05:19.943 READ DMA
c8 00 03 6c 5d 7e f0 7e 00:05:14.801 READ DMA
c8 00 04 6b 5d 7e f0 7e 00:05:09.660 READ DMA
c8 00 05 6a 5d 7e f0 7e 00:05:04.518 READ DMA
c8 00 06 69 5d 7e f0 7e 00:04:59.376 READ DMA
Error 672 occurred at disk power-on lifetime: 3080 hours (128 days + 8 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 6e 5d 7e f0 Error: UNC 1 sectors at LBA = 0x007e5d6e = 8281454
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 03 6c 5d 7e f0 7e 00:05:14.801 READ DMA
c8 00 04 6b 5d 7e f0 7e 00:05:09.660 READ DMA
c8 00 05 6a 5d 7e f0 7e 00:05:04.518 READ DMA
c8 00 06 69 5d 7e f0 7e 00:04:59.376 READ DMA
c8 00 07 68 5d 7e f0 7e 00:04:54.235 READ DMA
Error 671 occurred at disk power-on lifetime: 3080 hours (128 days + 8 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 6e 5d 7e f0 Error: UNC 1 sectors at LBA = 0x007e5d6e = 8281454
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 6b 5d 7e f0 7e 00:05:09.660 READ DMA
c8 00 05 6a 5d 7e f0 7e 00:05:04.518 READ DMA
c8 00 06 69 5d 7e f0 7e 00:04:59.376 READ DMA
c8 00 07 68 5d 7e f0 7e 00:04:54.235 READ DMA
c8 00 08 67 5d 7e f0 7e 00:04:49.096 READ DMA
Error 670 occurred at disk power-on lifetime: 3080 hours (128 days + 8 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 6e 5d 7e f0 Error: UNC 1 sectors at LBA = 0x007e5d6e = 8281454
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 05 6a 5d 7e f0 7e 00:05:04.518 READ DMA
c8 00 06 69 5d 7e f0 7e 00:04:59.376 READ DMA
c8 00 07 68 5d 7e f0 7e 00:04:54.235 READ DMA
c8 00 08 67 5d 7e f0 7e 00:04:49.096 READ DMA
c8 00 01 5e 29 00 f0 00 00:04:49.060 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging