rendered paste body __ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: RD-88F5181L-VOIP-GE LE
U-Boot 1.1.1 (Mar 29 2006 - 03:28:49) Marvell version: 1.7.3
DRAM CS[0] base 0x00000000 size 32MB
DRAM Total size 32MB
[8192kB@ff800000] Flash: 8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5181 B1
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>> ?
? - alias for 'help'
FSdel - del a file from the Flash MV FS
FSdir - ls the Flash MV FS
FSformat- format the Flash MV FS
FSlef - Load an exe file to the Flash MV FS
FSlf - Load a file to the Flash MV FS
FSrun - Load an exe file from the Flash MV FS and run it
FStftp - tftp a file to the Flash MV FS
FStftpe - tftp an exe file to the Flash MV FS
FStype - cat file from the Flash MV FS
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bubt - Burn an image on the Boot Flash.
chpart - change active partition
cmp - memory compare
cmpm - Compare Memory
cp - memory copy
cpumap - Display CPU memory mapping settings.
crc32 - checksum calculation
date - get/set/reset date & time
dclk - Display the MV device CLKs.
ddimm - Display SPD Dimm Info
dhcp - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
dma - Perform DMA
echo - echo args to console
eeprom - EEPROM sub-system
erase - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fi - Find value in the memory.
flinfo - print FLASH memory information
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
g - start application at cached address 'addr'(default addr 0x40000)
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
ide - IDE sub-system
iloop - infinite loop on address range
imd - i2c memory display
imm - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
ir - reading and changing MV internal register values.
ln - Load S-Record executable file through the network interface.
loop - infinite loop on address range
ls - list files in a directory (default /)
map - Diasplay address decode windows
md - memory display
me - PCI master enable
mm - memory modify (auto-incrementing)
mp - map PCI BAR
mtest - simple RAM test
mw - memory write (fill)
nm - memory modify (constant address)
pci - list and access PCI Configuraton Space
phyRead - Read Phy register
phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
resetenv - Return all environment variable to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
se - PCI Slave enable
setenv - set environment variables
sg - scanning the PHYs status
sleep - delay execution for some time
sp - Scan PCI bus.
tftpboot- boot image via network using TFTP protocol
version - print monitor version
Marvell>> boot
### JFFS2 loading 'uImage' to 0x400000
Scanning JFFS2 FS: ..... done.
### JFFS2 load complete: 885332 bytes loaded to 0x400000
## Booting image at 00400000 ...
Image Name: Linux-2.4.27-vrs1
Created: 2006-04-18 7:02:07 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 885268 Bytes = 864.5 kB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................
ZLinux version 2.4.27-vrs1 (joshua@localhost.localdomain) (gcc version 3.4.4 (r6
CPU: ARM926EJ-Sid(wb) revision 0
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 166000000, Tclk = 166000000
- Warning - This LSP release was tested only with U-Boot release 1.7.0
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rw ip=192.168.1.1e
gppMask = [0x130]
Calibrating delay loop... 331.77 BogoMIPS
Memory: 32MB 0MB 0MB 0MB = 32MB total
Memory: 30344KB available (1646K code, 311K data, 72K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
CPU: Testing write buffer: pass
POSIX conformance testing by UNIFIX
init hw started.
PCI: bus0: Fast back to back transfers enabled
No init hw.
PCI: bus1: Fast back to back transfers enabled
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
bankwidth 2, base f4000000, size 1000000
Marvell Development Board (LSP Version 0.0.102)-- RD-88F5181L-VOIP-GE
Detected Tclk 166000000 and SysClk 166000000
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ed
ttyS00 at 0xf1012000 (irq = 3) is a 16550A
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Loading network interface
o Using switch header mode
qdInit
BoardID = eqdStart: CPU port 0x3
----set PPU En
Switch driver initialized
Can't get netConfig: Use default
UNM is not initialized yet
2 VLANs created: CpuPortMask = 0xa7
vid=0: DISABLED(0), portMask=0x750, portNum=5
vid=1: VLAN_1, portMask=0x04, portNum=1
vid=2: VLAN_2, portMask=0xa3, portNum=4
vid=12: ISOLATED(12), portMask=0x00, portNum=0
Port - Vlan
0 - VLAN_2
1 - VLAN_2
2 - VLAN_1
3 - VLAN_ALL
4 - DISABLED(0)
5 - VLAN_2
6 - DISABLED(0)
7 - VLAN_2
load virtual interface vid = 1
register if with name
Init the hal
: Ilegal MTU value 1500, rounding MTU to: 1506
if eth0 registered
load virtual interface vid = 2
register if with name
if eth1 registered
PPP generic driver version 2.4.2
physmap flash device: 1000000 at f4000000
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Using physmap partition definition
Creating 6 MTD partitions on "phys_mapped_flash":
0x00000000-0x00600000 : "root"
0x00600000-0x00620000 : "nvram"
0x00620000-0x00640000 : "nvram default"
0x00640000-0x00660000 : "POT"
0x00660000-0x00680000 : "Traffic Meter"
0x00700000-0x00800000 : "uboot"
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 340 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Fast Floating Point Emulator V0.94M by Peter Teichmann.
cramfs: wrong magic
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing init memory: 72K
8Zinit: Missing PROCESS field in inittabinit: Missing PROCESS field in inittabi]
Warning: loading gpio_module will taint the kernel: non-GPL license - Gemtek
See http://www.tux.org/lkml/#export-tainted for information about tainted mods
resetC.c :Parent process, pid = 22
resetC.c :Child process, pid = 26
Thu Jan 1 00:00:00 UTC 1970
(http)This is the parent process, pid = 24
# update nvram with default list!
Init interfaces.
can't get macaddr of ap0
(http)This is the child process, pid = 30
eth1: mac address changed
device eth1 entered promiscuous mode
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
interface ap0 does not exist!
br0: port 1(eth1) entering listening state
Init lan services.
00 , MBaker-T42(nvram_unset)exclusive zone
shared_nvram->writing 1
Start UPnP
route: resolving netmask
route: resolving netmask
route: resolving netmask
route: resolving netmask
route: resolving netmask
Init wan.
BusyBox v1.1.0 (2006.04.13-11:35+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/ # eth0: mac address changed
eth0: Ilegal MTU value 1500, rounding MTU to: 1506
eth0: change mtu 1506 (buffer-size 1528) to 1506 (buffer-size 1528)
total_entry is 0
httpd : This is httpd...ssl_enabled is 0
/ # cat /proc/cpuinfo
Processor : ARM926EJ-Sid(wb) rev 0 (v5EJl)
BogoMIPS : 331.77
Features : swp half thumb fastmult
Hardware : MV-88fxx81
Revision : 0000
Serial : 0000000000000000
/ #