rendered paste body
ntb_tux ~ # modprobe ipw2200
WARNING: Error inserting ieee80211_crypt (/lib/modules/2.6.17-gentoo-r2/net/ieee80211/ieee80211_crypt.ko): Invalid module format
WARNING: Error inserting ieee80211 (/lib/modules/2.6.17-gentoo-r2/net/ieee80211/ieee80211.ko): Invalid module format
ntb_tux ~ # dmesg
7d0000 (usable)
BIOS-e820: 000000001f7d0000 - 000000001f7efc00 (reserved)
BIOS-e820: 000000001f7efc00 - 000000001f7fb000 (ACPI NVS)
BIOS-e820: 000000001f7fb000 - 000000001f800000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
503MB LOWMEM available.
On node 0 totalpages: 128976
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 124880 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 HP ) @ 0x000fe270
ACPI: RSDT (v001 HP 099C 0x25070520 HP 0x00000001) @ 0x1f7efc84
ACPI: FADT (v002 HP 099C 0x00000002 HP 0x00000001) @ 0x1f7efc00
ACPI: MADT (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x1f7efcb8
ACPI: MCFG (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x1f7efd14
ACPI: SSDT (v001 HP HPQPpc 0x00001001 MSFT 0x0100000e) @ 0x1f7f79a7
ACPI: DSDT (v001 HP DAU00 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfec01000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1f800000:c0800000)
Built 1 zonelists
Kernel command line: root=/dev/hda4
mapped APIC to ffffd000 (fec01000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1729.182 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 507168k/515904k available (2462k kernel code, 8184k reserved, 779k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2995.21 BogoMIPS (lpj=1497606)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI Error (evgpeblk-0284): Unknown GPE method type: C20A (name not of form _Lxx or _Exx) [20060127]
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [C002] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C002] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C002.C068._PRT]
ACPI: Embedded Controller [C004] (gpe 16) interrupt mode.
ACPI: Power Resource [C1C1] (on)
ACPI: PCI Interrupt Link [C0D8] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DB] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0EE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0EF] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0F0] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0F1] (IRQs 10 11) *0, disabled.
ACPI: Power Resource [C25C] (off)
ACPI: Power Resource [C25D] (off)
ACPI: Power Resource [C25E] (off)
ACPI: Power Resource [C25F] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:09: ioport range 0x1000-0x107f could not be reserved
pnp: 00:09: ioport range 0x1100-0x113f has been reserved
pnp: 00:09: ioport range 0x1200-0x121f has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: d0000000-d03fffff
PREFETCH window: 20000000-21ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
NTFS driver 2.1.27 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
[drm] Initialized i915 1.4.0 20060119 on minor 0
ACPI: AC Adapter [C16F] (on-line)
ACPI: Battery Slot [C171] (battery present)
ACPI: Battery Slot [C170] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C1E4]
ACPI: Lid Switch [C1E5]
ACPI: Fan [C260] (off)
ACPI: Fan [C261] (off)
ACPI: Fan [C262] (off)
ACPI: Fan [C263] (off)
ACPI: Video Device [C055] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (100 C)
ACPI: Thermal Zone [TZ2] (74 C)
ACPI: Thermal Zone [TZ3] (38 C)
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
b44.c:v1.00 (Apr 7, 2006)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:14:c2:d5:79:30
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 17
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2580-0x2587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: IC25N060ATMR04-0, ATA DISK drive
hdb: TSSTcorpCD/DVDW TS-L532M, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xd0580000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 18, io base 0x00002000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00002040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x00002060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:C1BE,PNP0f13:C1BF] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
i2c /dev entries driver
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
ip_conntrack version 2.4 (4030 buckets, 32240 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
TIPC: Activated (compiled Jul 9 2006 10:12:34)
NET: Registered protocol family 30
TIPC: Started in single node mode
Using IPI Shortcut mode
ACPI wakeup devices:
C068 C0BB C0C2 C0C3 C0C4 C0C5
ACPI: (supports S0 S3 S4 S5)
EXT2-fs warning (device hda4): ext2_fill_super: mounting ext3 filesystem as ext2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 192k freed
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
Adding 514072k swap on /dev/hda3. Priority:-1 extents:1 across:514072k
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
Warning: Processor Platform Limit event detected, but not handled.
Consider compiling CPUfreq support into your kernel.
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
b44: eth0: Link is up at 10 Mbps, half duplex.
b44: eth0: Flow control is off for TX and off for RX.
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)
usb 3-2: USB disconnect, address 2
ieee80211_crypt: exports duplicate symbol ieee80211_crypt_deinit_entries (owned by kernel)
ieee80211: exports duplicate symbol alloc_ieee80211 (owned by kernel)