rendered paste bodyserver:~# smartctl -a /dev/hdc
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG SP0802N
Serial Number: 0733J3FX169425
Firmware Version: TK100-24
User Capacity: 80,060,424,192 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sat Dec 22 21:57:14 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (2880) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 48) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 3
3 Spin_Up_Time 0x0007 072 056 000 Pre-fail Always - 5056
4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4152
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 1
7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0
9 Power_On_Half_Minutes 0x0032 099 099 000 Old_age Always - 6921h+40m
10 Spin_Retry_Count 0x0013 253 253 049 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2578
194 Temperature_Celsius 0x0022 196 091 000 Old_age Always - 14
195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 174430435
196 Reallocated_Event_Count 0x0012 100 100 000 Old_age Always - 1
197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0
198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0
199 UDMA_CRC_Error_Count 0x000b 100 100 051 Pre-fail Always - 6
200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 1
201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0
SMART Error Log Version: 1
ATA Error Count: 1611 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1611 occurred at disk power-on lifetime: 6737 hours (280 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 00 00 f0 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 f0 00 00:02:34.438 READ DMA
Error 1610 occurred at disk power-on lifetime: 6737 hours (280 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 00 00 f0 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 f0 00 00:02:34.063 READ DMA
10 00 3f 00 00 00 f0 00 00:02:04.000 RECALIBRATE [OBS-4]
Error 1609 occurred at disk power-on lifetime: 6737 hours (280 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 00 00 f0 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 f0 00 00:02:03.625 READ DMA
Error 1608 occurred at disk power-on lifetime: 6737 hours (280 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 00 00 f0 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 f0 00 00:02:03.188 READ DMA
10 00 3f 00 00 00 f0 00 00:02:03.188 RECALIBRATE [OBS-4]
e1 00 07 81 eb ef f3 00 00:02:02.750 IDLE IMMEDIATE
c8 00 08 80 eb ef f3 00 00:02:02.313 READ DMA
10 00 3f 00 00 00 f0 00 00:01:56.375 RECALIBRATE [OBS-4]
Error 1607 occurred at disk power-on lifetime: 6737 hours (280 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 00 00 f0 Error: ICRC, ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 f0 00 00:01:55.938 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
server:~#