rendered paste bodyLinux version 2.6.18-5-686 (Debian 2.6.18.dfsg.1-13) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Fri Jun 1 00:47:00 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bfe0000 (usable)
BIOS-e820: 000000000bfe0000 - 000000000bff0000 (ACPI data)
BIOS-e820: 000000000bff0000 - 000000000c000000 (reserved)
BIOS-e820: 00000000100a0000 - 00000000100b6e00 (reserved)
BIOS-e820: 00000000100b6e00 - 00000000100b7000 (ACPI NVS)
BIOS-e820: 00000000100b7000 - 0000000010100000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
191MB LOWMEM available.
On node 0 totalpages: 49120
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 45024 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f7550
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x0bfe0000
ACPI: FADT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x0bfe0054
ACPI: DSDT (v001 TOSHIB 2740 0x20000228 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0xfe08
Allocating PCI resources starting at 20000000 (gap: 10100000:efe80000)
Detected 497.590 MHz processor.
Built 1 zonelists. Total pages: 49120
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01189000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 187196k/196480k available (1541k kernel code, 8792k reserved, 576k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 996.04 BogoMIPS (lpj=1992080)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0a00)
CPU0: Intel Celeron (Coppermine) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4383k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xff85c, last bus=21
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region fe00-fe3f claimed by PIIX4 ACPI
PCI quirk: region fe70-fe7f claimed by PIIX4 SMB
PIIX4 devres B PIO at 006c-006f
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [PIHD] (on)
ACPI: Power Resource [PMHD] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
PCI: setting IRQ 13 as level-triggered
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f0000000-f7ffffff
PREFETCH window: 28000000-280fffff
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0b.1
IO window: 00001800-000018ff
IO window: 00002000-000020ff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Enabling device 0000:00:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Enabling device 0000:00:0b.1 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1195855633.180:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (64 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:05.2: UHCI Host Controller
uhci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:05.2: irq 11, io base 0x0000ff80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:05.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
hda: TOSHIBA MK1214GAP, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DV-28E-0, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 23579136 sectors (12072 MB), CHS=23392/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 >
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
piix4_smbus 0000:00:05.3: Found 0000:00:05.3 device
Yenta: CardBus bridge found at 0000:00:0b.0 [1179:0001]
Linux video capture interface: v2.00
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
Yenta: CardBus bridge found at 0000:00:0b.1 [1179:0001]
Linux agpgart interface v0.101 (c) Dave Jones
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000011
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
videodev: "Maestro radio" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/
maestro_radio: probe of 0000:00:0c.0 failed with error -5
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 128M @ 0xe8000000
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
pccard: PCMCIA card inserted into slot 1
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
ts: Compaq touchscreen protocol output
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia1.0
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
es1968: clocking to 48000
Adding 425680k swap on /dev/hda5. Priority:-1 extents:1 across:425680k
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
ne.c: You must supply "io=0xNNN" value(s) for ISA cards.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized savage 2.4.1 20050313 on minor 0
mtrr: no more MTRRs available
mtrr: base(0xf2000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
pccard: card ejected from slot 1
pccard: PCMCIA card inserted into slot 1
pcmcia: registering new device pcmcia1.0