rendered paste bodysmartctl version 5.37 [x86_64-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200AAKS-00SBA0
Serial Number: WD-WMAPZ0464810
Firmware Version: 12.01B01
User Capacity: 320,072,933,376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Nov 21 17:23:40 2007 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (8400) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 159 157 021 Pre-fail Always - 5041
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 260
5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 2
7 Seek_Error_Rate 0x000e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 945
10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 179
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 17
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 260
194 Temperature_Celsius 0x0022 112 097 000 Old_age Always - 35
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 2
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 22 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 22 occurred at disk power-on lifetime: 925 hours (38 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 0a ba 49 e0 Error: UNC at LBA = 0x0049ba0a = 4831754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 0a ba 49 05 00 01:11:18.471 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:18.471 READ DMA EXT
42 ff 01 09 ba 49 05 00 01:11:18.471 READ VERIFY SECTOR(S) EXT
42 ff 02 0d ba 49 05 00 01:11:18.461 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:18.461 READ DMA EXT
Error 21 occurred at disk power-on lifetime: 925 hours (38 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 0b ba 49 e0 Error: UNC at LBA = 0x0049ba0b = 4831755
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 02 0b ba 49 05 00 01:11:15.546 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:15.546 READ DMA EXT
42 ff 02 09 ba 49 05 00 01:11:12.907 READ VERIFY SECTOR(S) EXT
42 ff 02 07 ba 49 05 00 01:11:12.907 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:12.907 READ DMA EXT
Error 20 occurred at disk power-on lifetime: 925 hours (38 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 09 ba 49 e0 Error: UNC at LBA = 0x0049ba09 = 4831753
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 02 09 ba 49 05 00 01:11:12.907 READ VERIFY SECTOR(S) EXT
42 ff 02 07 ba 49 05 00 01:11:12.907 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:12.907 READ DMA EXT
42 ff 04 0b ba 49 05 00 01:11:10.260 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:10.260 READ DMA EXT
Error 19 occurred at disk power-on lifetime: 925 hours (38 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 0b ba 49 e0 Error: UNC at LBA = 0x0049ba0b = 4831755
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 04 0b ba 49 05 00 01:11:10.260 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:10.260 READ DMA EXT
42 ff 04 07 ba 49 05 00 01:11:07.489 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:07.489 READ DMA EXT
42 ff 08 07 ba 49 05 00 01:11:04.577 READ VERIFY SECTOR(S) EXT
Error 18 occurred at disk power-on lifetime: 925 hours (38 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 07 ba 49 e0 Error: UNC at LBA = 0x0049ba07 = 4831751
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 04 07 ba 49 05 00 01:11:07.489 READ VERIFY SECTOR(S) EXT
25 ff 01 00 00 00 00 00 01:11:07.489 READ DMA EXT
42 ff 08 07 ba 49 05 00 01:11:04.577 READ VERIFY SECTOR(S) EXT
42 ff 08 ff b9 49 05 00 01:11:04.577 READ VERIFY SECTOR(S) EXT
42 ff 10 0f ba 49 05 00 01:11:04.566 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 931 -
# 2 Short offline Completed without error 00% 930 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.