rendered paste body=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 093 088 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 100 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 88
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 30246569931
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1821
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 275
187 Unknown_Attribute 0x0032 098 098 000 Old_age Always - 2
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 064 058 045 Old_age Always - 606339108
194 Temperature_Celsius 0x0022 036 042 000 Old_age Always - 36 (Lifetime Min/Max 0/23)
195 Hardware_ECC_Recovered 0x001a 070 054 000 Old_age Always - 15
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 c0 1e 04 e0 Error: UNC at LBA = 0x00041ec0 = 270016
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 70 bd 1e 04 e0 00 00:00:54.067 READ DMA EXT
25 00 78 b5 1e 04 e0 00 00:00:54.066 READ DMA EXT
25 00 08 ad 1e 04 e0 00 00:00:54.065 READ DMA EXT
25 00 f8 8d 1d 04 e0 00 00:00:54.063 READ DMA EXT
25 00 08 85 1d 04 e0 00 00:00:55.826 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 c0 1e 04 e0 Error: UNC at LBA = 0x00041ec0 = 270016
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 78 b5 1e 04 e0 00 00:00:54.067 READ DMA EXT
25 00 08 ad 1e 04 e0 00 00:00:54.066 READ DMA EXT
25 00 f8 8d 1d 04 e0 00 00:00:54.065 READ DMA EXT
25 00 08 85 1d 04 e0 00 00:00:54.063 READ DMA EXT
25 00 00 d5 1a 04 e0 00 00:00:54.062 READ DMA EXT
Error 8 occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 00 00 00 e0 00 00:04:02.766 READ DMA EXT
29 03 01 00 00 00 e0 00 00:04:02.744 READ MULTIPLE EXT
ef 03 45 01 10 00 a0 02 00:04:02.744 SET FEATURES [Set transfer mode]
ef 03 0c 01 10 00 a0 02 00:04:02.744 SET FEATURES [Set transfer mode]
c6 00 10 01 00 00 a0 02 00:04:02.743 SET MULTIPLE MODE
Error 7 occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 e0 00 00:03:52.708 READ DMA EXT
ec 00 00 00 00 00 a0 00 00:03:52.708 IDENTIFY DEVICE
b0 d8 00 00 4f c2 a0 00 00:03:52.701 SMART ENABLE OPERATIONS
b0 da 00 00 4f c2 a0 00 00:03:42.706 SMART RETURN STATUS
b0 d8 00 00 4f c2 a0 00 00:03:42.696 SMART ENABLE OPERATIONS
Error 6 occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 e0 00 00:03:32.638 READ DMA EXT
ec 00 00 00 00 00 a0 00 00:03:32.638 IDENTIFY DEVICE
29 03 01 00 00 00 e0 00 00:03:32.630 READ MULTIPLE EXT
ef 03 45 01 10 00 a0 02 00:03:42.706 SET FEATURES [Set transfer mode]
ef 03 0c 01 10 00 a0 02 00:03:42.696 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.