Stuff

Nov  9 09:02:51 paez kernel: QLogic Fibre Channel HBA Driver
Nov  9 09:02:51 paez kernel: PCI: Enabling device 0000:06:01.0 (0150 -> 0153)
Nov  9 09:02:51 paez kernel: ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 24 (level, low) -> IRQ 177
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Found an ISP2312, irq 177, iobase 0xf893e000
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Configuring PCI space...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Configure NVRAM parameters...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Verifying loaded RISC code...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Allocated (412 KB) for firmware dump...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: LIP reset occured (f7f7).
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Waiting for LIP to complete...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: LOOP UP detected (2 Gbps).
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Waiting for LIP to complete...
Nov  9 09:02:51 paez kernel: qla2xxx 0000:06:01.0: Topology - (F_Port), Host Loop address 0xffff
Nov  9 09:02:52 paez kernel: scsi2 : qla2xxx
Nov  9 09:02:52 paez kernel: qla2xxx 0000:06:01.0: 
Nov  9 09:02:52 paez kernel:  QLogic Fibre Channel HBA Driver: 8.01.07-k1
Nov  9 09:02:52 paez kernel:   QLogic QLA2340 - 
Nov  9 09:02:52 paez kernel:   ISP2312: PCI-X (100 MHz) @ 0000:06:01.0 hdma-, host#=2, fw=3.03.20 IPX
Nov  9 09:02:52 paez kernel:   Vendor: HP        Model: MSL6000 Series    Rev: 0516
Nov  9 09:02:52 paez kernel:   Type:   Medium Changer                     ANSI SCSI revision: 02
Nov  9 09:02:52 paez kernel:   Vendor: HP        Model: Ultrium 2-SCSI    Rev: F68W
Nov  9 09:02:52 paez kernel:   Type:   Sequential-Access                  ANSI SCSI revision: 03
Nov  9 09:02:52 paez kernel:   Vendor: HP        Model: Ultrium 2-SCSI    Rev: F68W
Nov  9 09:02:52 paez kernel:   Type:   Sequential-Access                  ANSI SCSI revision: 03
Nov  9 09:02:52 paez kernel: SCSI Media Changer driver v0.25 
Nov  9 09:02:52 paez kernel: ch0: type #1 (mt): 0x0+1 [medium transport]
Nov  9 09:02:52 paez kernel: ch0: type #2 (st): 0x20+29 [storage]
Nov  9 09:02:52 paez kernel: ch0: type #3 (ie): 0x1c0+1 [import/export]
Nov  9 09:02:52 paez kernel: ch0: type #4 (dt): 0x1e0+2 [data transfer]
Nov  9 09:02:52 paez kernel: ch0: dt 0x1e0: ID 1, LUN 0, Huh? device not found!
Nov  9 09:02:52 paez kernel: ch0: dt 0x1e1: ID 2, LUN 0, Huh? device not found!
Nov  9 09:02:52 paez kernel: ch0: INITIALIZE ELEMENT STATUS, may take some time ...
Nov  9 09:02:52 paez kernel: st: Version 20050830, fixed bufsize 32768, s/g segs 256
Nov  9 09:03:05 paez kernel: ch0: ... finished
Nov  9 09:03:05 paez kernel: ch 2:0:0:0: Attached scsi changer ch0
Nov  9 09:03:05 paez kernel: st 2:0:0:1: Attached scsi tape st0
Nov  9 09:03:05 paez kernel: st0: try direct i/o: yes (alignment 512 B)
Nov  9 09:03:05 paez kernel: st 2:0:0:2: Attached scsi tape st1
Nov  9 09:03:05 paez kernel: st1: try direct i/o: yes (alignment 512 B)
Nov  9 09:03:05 paez kernel: sd 1:0:0:0: Attached scsi generic sg0 type 0
Nov  9 09:03:05 paez kernel: ch 2:0:0:0: Attached scsi generic sg1 type 8
Nov  9 09:03:05 paez kernel: st 2:0:0:1: Attached scsi generic sg2 type 1
Nov  9 09:03:05 paez kernel: st 2:0:0:2: Attached scsi generic sg3 type 1