rendered paste bodyLinux version 2.6.22.6 (root@trinite-2) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #4 SMP Thu Sep 13 21:08:49 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS)
BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data)
BIOS-e820: 00000000d0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f3f60
Entering add_active_range(0, 0, 261872) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 261872
early_node_map[1] active PFN ranges
0: 0 -> 261872
On node 0 totalpages: 261872
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 253 pages used for memmap
HighMem zone: 32243 pages, LIFO batch:7
DMI 2.4 present.
Using APIC driver default
ACPI: RSDP 000F7F30, 0014 (r0 Nvidia)
ACPI: RSDT 3FEF3040, 0038 (r1 Nvidia NVDAACPI 42302E31 NVDA 0)
ACPI: FACP 3FEF30C0, 0074 (r1 Nvidia NVDAACPI 42302E31 NVDA 0)
ACPI: DSDT 3FEF3180, 5349 (r1 NVIDIA NVDAACPI 1000 MSFT 3000000)
ACPI: FACS 3FEF0000, 0040
ACPI: HPET 3FEF8640, 0038 (r1 Nvidia NVDAACPI 42302E31 NVDA 98)
ACPI: WDRT 3FEF86C0, 0047 (r1 Nvidia NVDAACPI 42302E31 NVDA 0)
ACPI: MCFG 3FEF8780, 003C (r1 Nvidia NVDAACPI 42302E31 NVDA 0)
ACPI: APIC 3FEF8540, 0098 (r1 Nvidia NVDAACPI 42302E31 NVDA 0)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3ff00000:90100000)
Built 1 zonelists. Total pages: 259827
Kernel command line: root=/dev/sda2 video=uvesafb:1024x768-32,mtrr:3,ywrap
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2400.106 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031996k/1047488k available (3313k kernel code, 14932k reserved, 1571k data, 304k init, 129984k highmem)
virtual kernel memory layout:
fixmap : 0xfff82000 - 0xfffff000 ( 500 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc05cd000 - 0xc0619000 ( 304 kB)
.data : 0xc043c552 - 0xc05c51ac (1571 kB)
.text : 0xc0100000 - 0xc043c552 (3313 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
Calibrating delay using timer specific routine.. 4803.80 BogoMIPS (lpj=9607600)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 19k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 971 Objects with 98 Devices 303 Methods 45 Regions
tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [02] enable : Transition to ACPI mode successful
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.01 BogoMIPS (lpj=9600022)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9603.81 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=97
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
evgpeblk-0956 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0956 [04] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9
evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 0 Runtime GPEs in this block
evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:............................................................................................
Initialized 45/45 Regions 1/1 Fields 36/36 Buffers 10/26 Packages (980 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:..
Executed 2 _INI methods requiring 2 _STA executions (examined 104 objects)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Firmware left 0000:02:09.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:0f.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LXV5] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LXV6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LXV7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LXV8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [AXV5] (IRQs 16) *0
ACPI: PCI Interrupt Link [AXV6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AXV7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AXV8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AUBA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AMA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASMB] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AUS2] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AIDE] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASA0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [ASA1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x1000-0x107f has been reserved
pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
pnp: 00:00: ioport range 0x1400-0x147f has been reserved
pnp: 00:00: ioport range 0x1480-0x14ff has been reserved
pnp: 00:00: ioport range 0x1800-0x187f has been reserved
pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
pnp: 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0d: iomem range 0xd0000-0xd3fff has been reserved
pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:07.0 to 64
Time: tsc clocksource has been installed.
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[cfeff000-cfeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:03.0
IO window: a000-afff
MEM window: cc000000-ceffffff
PREFETCH window: b0000000-bfffffff
PCI: Bridge: 0000:00:0f.0
IO window: 9000-9fff
MEM window: cfc00000-cfefffff
PREFETCH window: 40000000-400fffff
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:0f.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W DEBUG].
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:01:00.0
uvesafb: NVIDIA Corporation, G71 Board - p455h7f , Chip Rev , OEM: NVIDIA, VBE v3.0
uvesafb: protected mode interface info at c000:c640
uvesafb: pmi: set display start = c00cc676, set palette = c00cc6e0
uvesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
uvesafb: VBIOS/hardware supports DDC2 transfers
uvesafb: monitor limits: vf = 75 Hz, hf = 80 kHz, clk = 140 MHz
uvesafb: scrolling: ywrap using protected mode interface, yres_virtual=1536
uvesafb: framebuffer at 0xb0000000, mapped to 0xf8880000, using 6144k, total 262144k
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [CPU0] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfeff0000 is busy
ACPI Error (utglobal-0126): Unknown exception code: 0xFFFFFFF0 [20070126]
Linux agpgart interface v0.102 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:09.0 to 64
e100: eth0: e100_probe: addr 0xcfefe000, irq 17, MAC addr 00:03:47:72:10:14
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
netconsole: not configured, aborting
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:0d.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xec00-0xec07, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: SONY DVD RW DW-G120A, ATAPI CD/DVD-ROM drive
ieee1394: Host added: ID:BUS[0-00:1023] GUID[808080050000044b]
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
sata_nv 0000:00:0e.0: version 3.4
ACPI: PCI Interrupt Link [ASA0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [ASA0] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x000109f0 ctl 0x00010bf2 bmdma 0x0001d800 irq 18
ata2: SATA max UDMA/133 cmd 0x00010970 ctl 0x00010b72 bmdma 0x0001d808 irq 18
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [ASA1] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [ASA1] -> GSI 22 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:0e.1 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x000109e0 ctl 0x00010be2 bmdma 0x0001c400 irq 19
ata4: SATA max UDMA/133 cmd 0x00010960 ctl 0x00010b62 bmdma 0x0001c408 irq 19
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0e.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:0e.2 to 64
scsi4 : sata_nv
scsi5 : sata_nv
ata5: SATA max UDMA/133 cmd 0x0001c000 ctl 0x0001bc02 bmdma 0x0001b000 irq 20
ata6: SATA max UDMA/133 cmd 0x0001b800 ctl 0x0001b402 bmdma 0x0001b008 irq 20
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
ata5.00: 488397168 sectors, multi 16: LBA48
ata5.00: configured for UDMA/133
ata6: SATA link down (SStatus 0 SControl 300)
scsi 4:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
sd 4:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 4:0:0:0: [sda] Attached SCSI disk
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [AUS2] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [AUS2] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 21, io mem 0xcfffe000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 18, io mem 0xcffff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
USB Universal Host Controller Interface driver v3.0
usb 2-6: new full speed USB device using ohci_hcd and address 2
usb 2-6: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Using IPI Shortcut mode
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 304k freed
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [AXV5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [AXV5] -> GSI 16 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.09 Sat May 26 00:47:07 PDT 2007
EXT3 FS on sda2, internal journal
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0f.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:0f.1 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/gspca_core.c: USB GSPCA camera found.(ZC3XX)
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/gspca_core.c: [spca5xx_probe:4098] Camera type JPEG
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/Vimicro/zc3xx.h: [zc3xx_config:515] Sensor ID:7
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/Vimicro/zc3xx.h: [zc3xx_config:597] Find Sensor HV7131R(c)
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/gspca_core.c: [spca5xx_getcapability:1215] maxw 640 maxh 480 minw 176 minh 144
usbcore: registered new interface driver gspca
/var/tmp/portage/media-video/gspcav1-20070508/work/gspcav1-20070508/gspca_core.c: gspca driver 01.00.18 registered
Adding 2168732k swap on /dev/sda1. Priority:-1 extents:1 across:2168732k