rendered paste bodyLinux version 2.6.12 (root@Knoppix) (gcc-Version 3.3.6 (Debian 1:3.3.6-7)) #2 SMP Tue Aug 9 23:20:52 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f6d3400 (usable)
BIOS-e820: 000000007f6d3400 - 0000000080000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4007000 (reserved)
BIOS-e820: 00000000f4008000 - 00000000f400c000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1142MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 521939
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 292563 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 DELL ) @ 0x000fc1b0
ACPI: RSDT (v001 DELL M07 0x27d70402 ASL 0x00000061) @ 0x7f6d39cd
ACPI: FADT (v001 DELL M07 0x27d70402 ASL 0x00000061) @ 0x7f6d4800
ACPI: HPET (v001 DELL M07 0x00000001 ASL 0x00000061) @ 0x7f6d4f00
ACPI: MADT (v001 DELL M07 0x27d70402 ASL 0x00000047) @ 0x7f6d5000
ACPI: MCFG (v016 DELL M07 0x27d70402 ASL 0x00000061) @ 0x7f6d4fc0
ACPI: SLIC (v001 DELL M07 0x27d70402 ASL 0x00000061) @ 0x7f6d509c
ACPI: BOOT (v001 DELL M07 0x27d70402 ASL 0x00000061) @ 0x7f6d4bc0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050624) @ 0x7f6d3a0d
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 80000000:70000000)
Built 1 zonelists
Kernel command line: ### isk_size=100000 init=/etc/init lang=de apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2063992k/2087756k available (1882k kernel code, 22540k reserved, 999k data, 296k init, 1170252k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Using HPET for gettimeofday
Detected 1995.179 MHz processor.
Using hpet for high-res timesource
Calibrating delay loop... 3940.35 BogoMIPS (lpj=1970176)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000040 0000e3bd 00000000 00000001
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
CPU0: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz stepping 06
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 3981.31 BogoMIPS (lpj=1990656)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000040 0000e3bd 00000000 00000001
CPU1: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz stepping 06
Total of 2 processors activated (7921.66 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs:
CPU#0 had 0 usecs TSC skew, fixed it up.
CPU#1 had 0 usecs TSC skew, fixed it up.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000003
groups: 00000001 00000002
CPU1 attaching sched-domain:
domain 0: span 00000003
groups: 00000002 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 845k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb316, last bus=14
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *4
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *3
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0x1000-0x1005 could not be reserved
pnp: 00:01: ioport range 0x1008-0x100f could not be reserved
pnp: 00:02: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:02: ioport range 0x1006-0x1007 has been reserved
pnp: 00:02: ioport range 0x100a-0x1059 could not be reserved
pnp: 00:02: ioport range 0x1060-0x107f has been reserved
pnp: 00:02: ioport range 0x1080-0x10bf has been reserved
pnp: 00:02: ioport range 0x10c0-0x10df has been reserved
pnp: 00:07: ioport range 0xc80-0xcff has been reserved
pnp: 00:07: ioport range 0x910-0x91f has been reserved
pnp: 00:07: ioport range 0x920-0x92f has been reserved
pnp: 00:07: ioport range 0xcb0-0xcbf has been reserved
pnp: 00:07: ioport range 0x930-0x97f has been reserved
Simple Boot Flag at 0x79 set to 0x1
Number of CPUs sharing cache didn't match any known set of CPUs
Number of CPUs sharing cache didn't match any known set of CPUs
audit: initializing netlink socket (disabled)
audit(1193094484.698:0): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: SONY DVD+/-RW DW-Q58A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.11 loaded.
ata_piix version 1.03
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:7f09 84:6063 85:3469 86:be09 87:6063 88:203f
ata1: dev 0 ATA, max UDMA/100, 234441648 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: FUJITSU MHV2120B Rev: 0085
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Cannot allocate resource for mainboard
Cannot allocate resource for EISA slot 1
EISA: Detected 0 cards.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP: routing cache hash table of 8192 buckets, 128Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 15
Starting balanced_irq
ACPI wakeup devices:
LID PBTN PCI0 USB0 USB1 USB2 USB3 EHCI AZAL PCIE RP01 RP02 RP03 RP04 RP05 RP06
ACPI: (supports S0 S3 S4 S4bios S5)
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: Intel Corporation I/O Controller Hub UHCI USB #1
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000bf80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: Intel Corporation I/O Controller Hub UHCI USB #2
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000bf60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: Intel Corporation I/O Controller Hub UHCI USB #3
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000bf40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: Intel Corporation I/O Controller Hub UHCI USB #4
usb 1-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000bf20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
Synaptics Touchpad, model: 1, fw: 6.2, id: 0xfa0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
usb 1-2: new low speed USB device using uhci_hcd and address 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[ef9fd800-ef9fdfff] Max Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: new full speed USB device using uhci_hcd and address 2
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ieee1394: Host added: ID:BUS[0-00:1023] GUID[334fc00020898c50]
Vendor: FUJITSU Model: NW10T6225H2V Rev: 0028
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 114270345 512-byte hdwr sectors (58506 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 114270345 512-byte hdwr sectors (58506 MB)
sdb: assuming drive cache: write through
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.02
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 82346 blocks, 65536 bytes/block, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
cloop: losetup_file: 29269 blocks, 65536 bytes/block, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs 20050921-1517
Freeing unused kernel memory: 296k freed
Real Time Clock Driver v1.12
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (58 C)
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
ts: Compaq touchscreen protocol output
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
hw_random hardware driver 1.0.0 loaded
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
b44.c:v0.95 (Aug 3, 2004)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:14:22:f0:6e:59
NET: Registered protocol family 17
b44: eth0: Link is down.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is on for TX and on for RX.
Linux agpgart interface v0.101 (c) Dave Jones
apm: BIOS not found.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is on for TX and on for RX.
mtrr: no more MTRRs available
NETDEV WATCHDOG: eth0: transmit timed out
b44: eth0: transmit timed out, resetting
b44: eth0: Link is down.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0381d00(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present