=> run nfsargs addip addtty
=> run loadlinux
Speed: 1000, full duplex
Using TSEC0 device
TFTP from server 192.168.1.24; our IP address is 192.168.1.83
Filename '2623'.
Load address: 0x200000
Loading: Got error 4
T #################################################################
#################################################################
#################################################################
#################################################################
###########################
done
Bytes transferred = 1465976 (165e78 hex)
Speed: 1000, full duplex
Using TSEC0 device
TFTP from server 192.168.1.24; our IP address is 192.168.1.83
Filename '2623.dtb'.
Load address: 0x400000
Loading: #
done
Bytes transferred = 3566 (dee hex)
## Booting image at 00200000 ...
Image Name: Linux-2.6.23
Created: 2007-10-18 20:07:31 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1465912 Bytes = 1.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Booting using flat device tree at 0x400000
Using MPC8313 RDB machine description
Linux version 2.6.23 (leon@witty) (gcc version 4.1.2) #1 Thu Oct 18 21:37:04 CEST 2007
console [udbg0] enabled
setup_arch: bootmem
mpc8313_rdb_setup_arch()
Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
arch: exit
Zone PFN ranges:
DMA 0 -> 32768
Normal 32768 -> 32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists in Zone order. Total pages: 32512
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.24:/nfsroot/rootfs ip=192.168.1.83:192.168.1.24:192.168.1.254:255.255.255.0:mpc8313erdb:eth0:off panic=1 console=ttyS0,115200
IPIC (128 IRQ sources) at fdefa700
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126632k/131072k available (2880k kernel code, 4276k reserved, 132k data, 91k bss, 152k init)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 18) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 21) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.2, 00:04:9f:ef:23:33
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:7e:21
eth1: Running with NAPI enabled
eth1: 256/256 RX/TX BD ring size
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
physmap platform flash device: 01000000 at fe000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
usbmon: debugfs is not available
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 38, io base 0xe0023000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
WDT driver for MPC83xx initialized. mode:reset timeout=65535 (25 seconds)
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
e0024520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
IP-Config: Device `eth0' not found.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Looking up port of RPC 100003/2 on 192.168.1.24
rpcbind: server 192.168.1.24 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.24
rpcbind: server 192.168.1.24 not responding, timed out
Root-NFS: Unable to get mountd port number from server, using default
mount: server 0.0.0.16 not responding, timed out
Root-NFS: Server returned error -5 while mounting /nfsroot/rootfs
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "nfs" or unknown-block(2,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
Rebooting in 1 seconds..