[mike in ~]> cat /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes, into the CPIO image, and additional
# binaries a given user may wish. This is run first, so may
# be used to override the actual binaries used in a given hook.
# (Existing files are NOT overwritten is already added)
# BINARIES are dependancy parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in anyway. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options,
# like so:
# FILES="/etc/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'modload' may be used in place of 'udev', but is not recommended
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
# This setup specifies all modules in the MODULES setting above.
# No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
#
# This setup will autodetect all modules for your system and should
# work as a sane default
# HOOKS="base udev autodetect ide scsi sata filesystems"
#
# This setup will generate a 'full' image which supports most systems.
# No autodetection is done.
# HOOKS="base udev ide scsi sata usb filesystems"
#
# This setup assembles an ide raid array with an encrypted root FS.
# Note: See 'mkinitcpio -H raid' for more information on raid devices.
# HOOKS="base udev ide raid encrypt filesystems"
#
# This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect ide scsi filesystems"
[mike in ~]> cat /etc/rc.conf
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/unimaps
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE=
HARDWARECLOCK="localtime"
TIMEZONE=US/Eastern
KEYMAP=us
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by hwdetect
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to disable it
#
MODULES=(i810 intel-agp b44 snd-intel8x0 psmouse)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="Mike"
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)
#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng !hotplug !pcmcia network netfs dbus hal alsa kdm)
# End of file