rendered paste bodySMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 079 065 006 Pre-fail Always - 213756131
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 212
5 Reallocated_Sector_Ct 0x0033 088 088 036 Pre-fail Always - 485
7 Seek_Error_Rate 0x000f 076 060 030 Pre-fail Always - 43413153
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2040
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 211
187 Unknown_Attribute 0x0032 090 090 000 Old_age Always - 10
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 062 053 045 Old_age Always - 655622182
194 Temperature_Celsius 0x0022 038 047 000 Old_age Always - 38 (Lifetime Min/Max 0/18)
195 Hardware_ECC_Recovered 0x001a 049 044 000 Old_age Always - 158553012
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 1949 hours (81 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff 28 6a e0 Error: UNC at LBA = 0x006a28ff = 6957311
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff 28 6a e0 00 00:01:26.183 READ DMA EXT
25 00 08 ff 28 66 e0 00 00:01:26.174 READ DMA EXT
25 00 08 ff 28 62 e0 00 00:01:26.166 READ DMA EXT
25 00 08 ff 28 5e e0 00 00:01:26.151 READ DMA EXT
25 00 08 ff 28 5a e0 00 00:01:26.049 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 1935 hours (80 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 04 cb 5e e2 Error: UNC at LBA = 0x025ecb04 = 39766788
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 18 f7 ca 5e e2 00 00:04:30.901 READ DMA
27 00 00 00 00 00 e0 00 00:04:30.685 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:04:30.632 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:04:30.627 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:04:25.696 READ NATIVE MAX ADDRESS EXT
Error 8 occurred at disk power-on lifetime: 1935 hours (80 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 04 cb 5e e2 Error: UNC at LBA = 0x025ecb04 = 39766788
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 18 f7 ca 5e e2 00 00:04:13.681 READ DMA
27 00 00 00 00 00 e0 00 00:04:08.267 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:04:08.211 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:04:08.199 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:04:25.696 READ NATIVE MAX ADDRESS EXT
Error 7 occurred at disk power-on lifetime: 1935 hours (80 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 0c cb 5e e2 Error: UNC at LBA = 0x025ecb0c = 39766796
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 18 f7 ca 5e e2 00 00:04:13.681 READ DMA
27 00 00 00 00 00 e0 00 00:04:08.267 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:04:08.211 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:04:08.199 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:04:07.916 READ NATIVE MAX ADDRESS EXT
Error 6 occurred at disk power-on lifetime: 1935 hours (80 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 01 cb 5e e2 Error: UNC at LBA = 0x025ecb01 = 39766785
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 18 f7 ca 5e e2 00 00:03:52.240 READ DMA
27 00 00 00 00 00 e0 00 00:04:08.267 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:04:08.211 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:04:08.199 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:04:07.916 READ NATIVE MAX ADDRESS EXT