bcm43xx driver
PCI: Enabling device 0001:10:12.0 (0004 -> 0006)
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
Adding 3026560k swap on /dev/hda4. Priority:-1 extents:1 across:3026560k
EXT3 FS on hda3, internal journal
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called, .active_key = 0, .level = 1, .enabled = 1, .encrypt = 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x122, pl 0x99 (2005-01-22 22:40:08)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
eth1: Link is up at 100 Mbps, full-duplex.
eth1: Pause is disabled
SoftMAC: Scanning finished: scanned 11 channels starting with channel 1
From my kernel config:
#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_WIRELESS_EXT=y
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
CONFIG_IEEE80211_DEBUG=y
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y
# CONFIG_RFKILL is not set
#
and in the drivers section:
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_LIBERTAS is not set
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_HOSTAP is not set
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
# CONFIG_ZD1211RW is not set
#
look for me on #debianppc using irc.freenode.net
Anything else that is needed?