rendered paste body[root@ivr1 ~]# cat /etc/zaptel.conf
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
span=3,1,0,esf,b8zs
bchan=25-47
dchan=48
loadzone=us
defaultzone=us
[root@ivr1 ~]# cat /etc/zapata.conf
cat: /etc/zapata.conf: No such file or directory
[root@ivr1 ~]# cat /etc/asterisk/zapata.conf
[channels]
switchtype=national
pridialplan=national
prilocaldialplan=national
musiconhold=default
language=en
signalling=pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
overlapdial=yes
rxgain=0.0
txgain=0.0
group=1
context=ivr
channel => 1-23
group=3
context=ivr
channel => 25-47
*CLI>
*CLI> pri show span 2
Primary D-channel: 48
Status: Provisioned, Down, Active
Switchtype: National ISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: -1
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
*CLI> pri show span 1
Primary D-channel: 24
Status: Provisioned, Up, Active
Switchtype: National ISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: -1
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
; here is "dmesg" output
pciehp: Address64 -------- Resource unparsed
Evaluate _OSC Set fails. Status = 0x0005
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm: Slot sun(0) at s:b:d:f=0x00:04:1f:00
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: Both _OSC and OSHP methods do not exist
pciehp: Address64 -------- Resource unparsed
Evaluate _OSC Set fails. Status = 0x0005
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm: Slot sun(0) at s:b:d:f=0x00:04:1f:00
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: Both _OSC and OSHP methods do not exist
pciehp: Address64 -------- Resource unparsed
Evaluate _OSC Set fails. Status = 0x0005
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm: Slot sun(0) at s:b:d:f=0x00:04:1f:00
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PBLO OSHP fails=0x5
pciehp: Both _OSC and OSHP methods do not exist
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 193, pci mem f881c000
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 169, io base 0000bce0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 177, io base 0000bcc0
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 185, io base 0000bca0
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 1-3: new high speed USB device using address 2
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 2 ports detected
ACPI: Power Button (FF) [PWRF]
EXT3 FS on sda2, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
device-mapper: dm-multipath version 1.0.4 loaded
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda3, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda7, type ext3), uses xattr
Adding 4192924k swap on /dev/sda6. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 already at revision 0x5 (current=0x5)
microcode: CPU1 already at revision 0x5 (current=0x5)
microcode: CPU2 already at revision 0x5 (current=0x5)
microcode: CPU3 already at revision 0x5 (current=0x5)
microcode: No new microdata for cpu 0
microcode: No new microdata for cpu 2
microcode: No new microdata for cpu 1
microcode: No new microdata for cpu 3
IA-32 Microcode Update Driver v1.14 unregistered
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0342040(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.2.6 Echo Canceller: KB1
ACPI: PCI interrupt 0000:0a:02.0[A] -> GSI 96 (level, low) -> IRQ 225
Found TE2XXP at base address fe1ffc00, remapped to f8940c00
TE2XXP version c01a0164, burst OFF, slip debug: OFF
FALC version: 00000005, Board ID: 00
Reg 0: 0x35c5d400
Reg 1: 0x35c5d000
Reg 2: 0xffffffff
Reg 3: 0x00000000
Reg 4: 0x00000001
Reg 5: 0x00000000
Reg 6: 0xc01a0164
Reg 7: 0x00001000
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE2XXP: Launching card: 0
TE2XXP: Setting up global serial parameters
Found a Wildcard: Wildcard TE210P
ACPI: PCI interrupt 0000:0a:03.0[A] -> GSI 101 (level, low) -> IRQ 233
Found TE2XXP at base address fe1ff800, remapped to f8968800
TE2XXP version c01a0164, burst OFF, slip debug: OFF
FALC version: 00000005, Board ID: 00
Reg 0: 0x358e6400
Reg 1: 0x358e6000
Reg 2: 0xffffffff
Reg 3: 0x00000000
Reg 4: 0x00000001
Reg 5: 0x00000000
Reg 6: 0xc01a0164
Reg 7: 0x00001000
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE2XXP: Launching card: 0
TE2XXP: Setting up global serial parameters
Found a Wildcard: Wildcard TE210P
eth0: no IPv6 routers present
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 340 bytes per conntrack
About to enter spanconfig!
Done with spanconfig!
About to enter spanconfig!
Done with spanconfig!
Registered tone zone 0 (United States / North America)
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
wct2xxp: Setting yellow alarm on span 1
2G: Got interrupt, status = 0000000d, GIS = 0081
SPAN 1: Primary Sync Source
2G: Got interrupt, status = 0000000a, GIS = 0080
VPM: Not Present
Completed startup!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
wct2xxp: Setting yellow alarm on span 1
2G: Got interrupt, status = 0000000d, GIS = 0081
2G: Got interrupt, status = 0000000a, GIS = 0080
SPAN 3: Primary Sync Source
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
VPM: Not Present
Completed startup!
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000b, GIS = 0081
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
2G: Got interrupt, status = 0000000a, GIS = 0080
wct2xxp: Clearing yellow alarm on span 1
About to enter spanconfig!
About to enter startup!
wct2xxp: Setting yellow alarm on span 1
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 1: Primary Sync Source
Completed startup!
About to enter spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 3: Primary Sync Source
Completed startup!
Registered tone zone 0 (United States / North America)
wct2xxp: Clearing yellow alarm on span 1
About to enter spanconfig!
About to enter startup!
wct2xxp: Setting yellow alarm on span 1
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 1: Primary Sync Source
Completed startup!
About to enter spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for ESF/B8ZS
SPAN 3: Primary Sync Source
Completed startup!
Registered tone zone 0 (United States / North America)
wct2xxp: Clearing yellow alarm on span 1