rendered paste bodydmesg
Linux version 2.6.16-gentoo-r9 (root@localhost) (gcc version 3.4.6 (Gentoo 3.4.6-r1, ssp-3.4.5-1.0, pie-8.7.9)) #4 SMP PREEMPT Thu Jun 8 11:52:25 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000077ea0000 (usable)
BIOS-e820: 0000000077ea0000 - 0000000077eb0000 (ACPI data)
BIOS-e820: 0000000077eb0000 - 0000000077f00000 (ACPI NVS)
BIOS-e820: 0000000077f00000 - 0000000078000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
1022MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7710
On node 0 totalpages: 491168
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 261792 pages, LIFO batch:31
DMI present.
ATI board detected. Disabling timer routing over 8254.
ACPI: RSDP (v000 TOSINV ) @ 0x000f76c0
ACPI: RSDT (v001 TOSINV RSDT 0x06040000 LTP 0x00000000) @ 0x77eabf9b
ACPI: FADT (v001 TOSINV Goldfish 0x06040000 ATI 0x000f4240) @ 0x77eafef6
ACPI: MADT (v001 TOSINV APIC 0x06040000 LTP 0x00000000) @ 0x77eaff6a
ACPI: MCFG (v001 TOSINV MCFG 0x06040000 LTP 0x00000000) @ 0x77eaffc4
ACPI: SSDT (v001 TOSINV Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x77eac1ce
ACPI: SSDT (v001 TOSINV CpuPm 0x00003000 INTL 0x20030224) @ 0x77eabfd3
ACPI: DSDT (v001 TOSINV SB450 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 78000000:68000000)
Built 1 zonelists
Kernel command line: root=/dev/sda3
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1592.876 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1941384k/1964672k available (3795k kernel code, 22140k reserved, 1215k data, 292k init, 1047168k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3192.18 BogoMIPS (lpj=1596090)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Celeron(R) M processor 1.60GHz stepping 08
Total of 1 processors activated (3192.18 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd82c, last bus=4
PCI: Using MMCONFIG
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 7) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PFA1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
pnp: 00:08: ioport range 0x220-0x22f has been reserved
pnp: 00:08: ioport range 0x400-0x401 has been reserved
pnp: 00:08: ioport range 0x40b-0x40b has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: c0100000-c01fffff
PREFETCH window: d0000000-dfffffff
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 0000a400-0000a4ff
IO window: 0000a800-0000a8ff
PREFETCH window: 80000000-81ffffff
MEM window: 84000000-85ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: c0200000-c02fffff
PREFETCH window: 80000000-81ffffff
PCI: Enabling device 0000:02:06.0 (0004 -> 0007)
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 16
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1149786459.125:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.26 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
toshiba: not a supported Toshiba laptop
ppdev: user-space parallel port driver
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN1] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [TZCR] (58 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0
synaptics: Toshiba Satellite A105 detected, limiting rate to 40pps.
input: SynPS/2 Synaptics TouchPad as /class/input/input2
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 20 (level, low) -> IRQ 17
eth0: RealTek RTL8139 at 0xf8822000, 00:a0:d1:37:cf:93, IRQ 17
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: DVD/CDRW UJDA770, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_sil 0000:00:12.0: version 0.9
PCI: Enabling device 0000:00:12.0 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 18
ata1: SATA max UDMA/100 cmd 0xF8824080 ctl 0xF882408A bmdma 0xF8824000 irq 18
ata2: SATA max UDMA/100 cmd 0xF88240C0 ctl 0xF88240CA bmdma 0xF8824008 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:0f00 82:746b 83:7f69 84:6063 85:f469 86:3d49 87:6063 88:203f
ata1: dev 0 ATA-7, max UDMA/100, 78140160 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: SATA link down (SStatus 0)
scsi1 : sata_sil
Vendor: ATA Model: HTS541040G9SA00 Rev: MB2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
SCSI Media Changer driver v0.25
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:02:06.0 [1179:ff10]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x01111122, devctl 0x44
Yenta: ISA IRQ mask 0x0ef8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
pcmcia: parent PCI bridge Memory window: 0x80000000 - 0x81ffffff
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0007000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0005000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0006000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.3
sl811: driver sl811-hcd, 19 May 2005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
i2c /dev entries driver
i2c-pca-isa: i/o base 0x000330. irq 10
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.5
wbsd: Copyright(c) Pierre Ossman
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 172 bytes per conntrack
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 4
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI Shortcut mode
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
EXT3-fs: sda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 246227
ext3_orphan_cleanup: deleting unreferenced inode 246226
EXT3-fs: sda3: 2 orphan inodes deleted
EXT3-fs: recovery complete.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 292k freed
Adding 2000556k swap on /dev/sda2. Priority:-1 extents:1 across:2000556k
EXT3 FS on sda3, internal journal
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (svn 1531)
ath_rate_sample: 1.2 (svn 1531)
ath_pci: 0.9.4.5 (svn 1531)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 17
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.8 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xc0200000, irq=17
ACPI Error (evevent-0312): No installed handler for fixed event [00000004] [20060127]
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 20
hda_codec: Unknown model for ALC861, trying auto-probe from BIOS...
[fglrx] Maximum main memory to use for locked dma buffers: 1774 MBytes.
[fglrx] module loaded - fglrx 8.25.18 [May 18 2006] on minor 0
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 22
[fglrx] total GART = 67108864
[fglrx] free GART = 51118080
[fglrx] max single GART = 51118080
[fglrx] total LFB = 127954944
[fglrx] free LFB = 119762944
[fglrx] max single LFB = 119762944
[fglrx] total Inv = 0
[fglrx] free Inv = 0
[fglrx] max single Inv = 0
[fglrx] total TIM = 0
hda-intel: Invalid position buffer, using LPIB read method instead.
ACPI Error (evevent-0312): No installed handler for fixed event [00000004] [20060127]
ACPI Error (evevent-0312): No installed handler for fixed event [00000000] [20060127]