;
; SIP Configuration example for Asterisk
;
; Syntax for specifying a SIP device in extensions.conf is
; SIP/devicename where devicename is defined in a section below.
;
; You may also use
; SIP/username@domain to call any SIP user on the Internet
; (Don't forget to enable DNS SRV records if you want to use this)
;
; If you define a SIP proxy as a peer below, you may call
; SIP/proxyhostname/user or SIP/user@proxyhostname
; where the proxyhostname is defined in a section below
;
; Useful CLI commands to check peers/users:
; sip show peers Show all SIP peers (including friends)
; sip show users Show all SIP users (including friends)
; sip show registry Show status of hosts we register with
;
; sip debug Show all SIP messages
;
; reload chan_sip.so Reload configuration file
; Active SIP peers will not be reconfigured
;
[general]
rfc2833compensate=yes
context=inbound ; Default context for incoming calls
;allowguest=no ; Allow or reject guest calls (default is yes,
; this can also be set to 'osp'
; if asterisk was compiled with OSP support.)
allowoverlap=no ; Disable overlap dialing support. (Default is yes)
;allowsubscribe=no ; Disable support for subscriptions. (Default is yes)
;realm=mydomain.tld ; Realm for digest authentication
; defaults to "asterisk"
; Realms MUST be globally unique according to RFC 3261
; Set this to your host name or domain name
bindport=5060 ; UDP Port to bind to (SIP standard port is 5060)
bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
; Note: Asterisk only uses the first host
; in SRV records
; Disabling DNS SRV lookups disables the
; ability to place SIP calls based on domain
; names to some other SIP users on the Internet
;domain=mydomain.tld ; Set default domain for this host
; If configured, Asterisk will only allow
; INVITE and REFER to non-local domains
; Use "sip show domains" to list local domains
;domain=mydomain.tld,mydomain-incoming
; Add domain and configure incoming context
; for external calls to this domain
;domain=1.2.3.4 ; Add IP address as local domain
; You can have several "domain" settings
;allowexternalinvites=no ; Disable INVITE and REFER to non-local domains
; Default is yes
;autodomain=yes ; Turn this on to have Asterisk add local host
; name and local IP to domain list.
;pedantic=yes ; Enable checking of tags in headers,
; international character conversions in URIs
; and multiline formatted headers for strict
; SIP compatibility (defaults to "no")
; See doc/README.tos for a description of these parameters.
;tos_sip=cs3 ; Sets TOS for SIP packets.
;tos_audio=ef ; Sets TOS for RTP audio packets.
;tos_video=af41 ; Sets TOS for RTP video packets.
;maxexpiry=3600 ; Maximum allowed time of incoming registrations
; and subscriptions (seconds)
;minexpiry=60 ; Minimum length of registrations/subscriptions (default 60)
;defaultexpiry=120 ; Default length of incoming/outoing registration
;t1min=100 ; Minimum roundtrip time for messages to monitored hosts
; Defaults to 100 ms
;notifymimetype=text/plain ; Allow overriding of mime type in MWI NOTIFY
;checkmwi=10 ; Default time between mailbox checks for peers
;vmexten=voicemail ; dialplan extension to reach mailbox sets the
; Message-Account in the MWI notify message
; defaults to "asterisk"
;recordhistory=yes ; Record SIP history by default
; (see sip history / sip no history)
;disallow=all ; First disallow all codecs
;allow=ulaw ; Allow codecs in order of preference
;allow=ilbc ;
;musicclass=default ; Sets the default music on hold class for all SIP calls
; This may also be set for individual users/peers
;language=en ; Default language setting for all users/peers
; This may also be set for individual users/peers
;relaxdtmf=yes ; Relax dtmf handling
;rtptimeout=60 ; Terminate call if 60 seconds of no RTP activity
; when we're not on hold
;rtpholdtimeout=300 ; Terminate call if 300 seconds of no RTP activity
; when we're on hold (must be > rtptimeout)
;trustrpid = no ; If Remote-Party-ID should be trusted
;sendrpid = yes ; If Remote-Party-ID should be sent
;progressinband=never ; If we should generate in-band ringing always
; use 'never' to never use in-band signalling, even in cases
; where some buggy devices might not render it
; Valid values: yes, no, never Default: never
;useragent=Asterisk PBX ; Allows you to change the user agent string
;promiscredir = no ; If yes, allows 302 or REDIR to non-local SIP address
; Note that promiscredir when redirects are made to the
; local system will cause loops since Asterisk is incapable
; of performing a "hairpin" call.
;usereqphone = no ; If yes, ";user=phone" is added to uri that contains
; a valid phone number
;dtmfmode = rfc2833 ; Set default dtmfmode for sending DTMF. Default: rfc2833
; Other options:
; info : SIP INFO messages
; inband : Inband audio (requires 64 kbit codec -alaw, ulaw)
; auto : Use rfc2833 if offered, inband otherwise
;compactheaders = yes ; send compact sip headers.
;sipdebug = yes ; Turn on SIP debugging by default, from
; the moment the channel loads this configuration
;subscribecontext = default ; Set a specific context for SUBSCRIBE requests
; Useful to limit subscriptions to local extensions
; Settable per peer/user also
;notifyringing = yes ; Notify subscriptions on RINGING state
;
;videosupport=yes ; Turn on support for SIP video
;maxcallbitrate=384 ; Maximum bitrate for video calls (default 384 kb/s)
; Videosupport and maxcallbitrate is settable
; for peers and users as well
;callevents=no ; generate manager events when sip ua
; performs events (e.g. hold)
;
; If regcontext is specified, Asterisk will dynamically create and destroy a
; NoOp priority 1 extension for a given peer who registers or unregisters with
; us. The actual extension is the 'regexten' parameter of the registering
; peer or its name if 'regexten' is not provided. More than one regexten may
; be supplied if they are separated by '&'. Patterns may be used in regexten.
;
;regcontext=sipregistrations
;
;----------------------------------------- OUTBOUND SIP REGISTRATIONS ------------------------
; Asterisk can register as a SIP user agent to a SIP proxy (provider)
; Format for the register statement is:
; register => user[:secret[:authuser]]@host[:port][/extension]
;
; If no extension is given, the 's' extension is used. The extension needs to
; be defined in extensions.conf to be able to accept calls from this SIP proxy
; (provider).
;
; host is either a host name defined in DNS or the name of a section defined
; below.
;
; Examples:
;
;register => 1234:password@mysipprovider.com
;
; This will pass incoming calls to the 's' extension
;
;
;register => 2345:password@sip_proxy/1234
;
; Register 2345 at sip provider 'sip_proxy'. Calls from this provider
; connect to local extension 1234 in extensions.conf, default context,
; unless you configure a [sip_proxy] section below, and configure a
; context.
; Tip 1: Avoid assigning hostname to a sip.conf section like [provider.com]
; Tip 2: Use separate type=peer and type=user sections for SIP providers
; (instead of type=friend) if you have calls in both directions
;registertimeout=20 ; retry registration calls every 20 seconds (default)
;registerattempts=10 ; Number of registration attempts before we give up
; 0 = continue forever, hammering the other server
; until it accepts the registration
; Default is 0 tries, continue forever
; for Asterlinkin your general section add this:
register => asdfasdf"xxx@asterlink.com/xxxxxxxx
;----------------------------------------- NAT SUPPORT ------------------------
; The externip, externhost and localnet settings are used if you use Asterisk
; behind a NAT device to communicate with services on the outside.
;externip = 200.201.202.203 ; Address that we're going to put in outbound SIP
; messages if we're behind a NAT
; The externip and localnet is used
; when registering and communicating with other proxies
; that we're registered with
externhost=asdf.com ; Alternatively you can specify an
; external host, and Asterisk will
; perform DNS queries periodically. Not
; recommended for production
; environments! Use externip instead
;externrefresh=10 ; How often to refresh externhost if
; used
; You may add multiple local networks. A reasonable
; set of defaults are:
;localnet=192.168.0.0/255.255.0.0; All RFC 1918 addresses are local networks
;localnet=10.0.0.0/255.0.0.0 ; Also RFC1918
;localnet=172.16.0.0/12 ; Another RFC1918 with CIDR notation
;localnet=169.254.0.0/255.255.0.0 ;Zero conf local network
; The nat= setting is used when Asterisk is on a public IP, communicating with
; devices hidden behind a NAT device (broadband router). If you have one-way
; audio problems, you usually have problems with your NAT configuration or your
; firewall's support of SIP+RTP ports. You configure Asterisk choice of RTP
; ports for incoming audio in rtp.conf
;
;nat=no ; Global NAT settings (Affects all peers and users)
; yes = Always ignore info and assume NAT
; no = Use NAT mode only according to RFC3581
; never = Never attempt NAT mode or RFC3581 support
; route = Assume NAT, don't send rport
; (work around more UNIDEN bugs)
;canreinvite=yes ; Asterisk by default tries to redirect the
; RTP media stream (audio) to go directly from
; the caller to the callee. Some devices do not
; support this (especially if one of them is
; behind a NAT).
; The default setting is YES. If you have all clients
; behind a NAT, or for some other reason wants
; Asterisk to stay in the audio path,
; you may want to turn this off
;ADDED
nat=yes
localnet=192.168.1.0/255.255.255.0
qualify=no
;----------------------------------------- REALTIME SUPPORT ------------------------
; For additional information on ARA, the Asterisk Realtime Architecture,
; please read realtime.txt and extconfig.txt in the /doc directory of the
; source code.
;
;rtcachefriends=yes ; Cache realtime friends by adding them to the internal list
; just like friends added from the config file only on a
; as-needed basis? (yes|no)
;rtupdate=yes ; Send registry updates to database using realtime? (yes|no)
; If set to yes, when a SIP UA registers successfully, the ip address,
; the origination port, the registration period, and the username of
; the UA will be set to database via realtime.
; If not present, defaults to 'yes'.
;rtautoclear=yes ; Auto-Expire friends created on the fly on the same schedule
; as if it had just registered? (yes|no|<seconds>)
; If set to yes, when the registration expires, the friend will
; vanish from the configuration until requested again. If set
; to an integer, friends expire within this number of seconds
; instead of the registration interval.
;ignoreregexpire=yes ; Enabling this setting has two functions:
;
; For non-realtime peers, when their registration expires, the
; information will _not_ be removed from memory or the Asterisk database
; if you attempt to place a call to the peer, the existing information
; will be used in spiteof it having expired
;
; For realtime peers, when the peer is retrieved from realtime storage,
; the registration information will be used regardless of whether
; it has expired or not; if it expires while the realtime peer
; is still in memory (due to caching or other reasons), the
; information will not be removed from realtime storage
;----------------------------------------- SIP DOMAIN SUPPORT ------------------------
; Incoming INVITE and REFER messages can be matched against a list of 'allowed'
; domains, each of which can direct the call to a specific context if desired.
; By default, all domains are accepted and sent to the default context or the
; context associated with the user/peer placing the call.
; Domains can be specified using:
; domain=<domain>[,<context>]
; Examples:
; domain=myasterisk.dom
; domain=customer.com,customer-context
;
; In addition, all the 'default' domains associated with a server should be
; added if incoming request filtering is desired.
; autodomain=yes
;
; To disallow requests for domains not serviced by this server:
; allowexternaldomains=no
; fromdomain=mydomain.tld ; When making outbound SIP INVITEs to
; non-peers, use your primary domain "identity"
; for From: headers instead of just your IP
; address. This is to be polite and
; it may be a mandatory requirement for some
; destinations which do not have a prior
; account relationship with your server.
[authentication]
; Global credentials for outbound calls, i.e. when a proxy challenges your
; Asterisk server for authentication. These credentials override
; any credentials in peer/register definition if realm is matched.
;
; This way, Asterisk can authenticate for outbound calls to other
; realms. We match realm on the proxy challenge and pick an set of
; credentials from this list
; Syntax:
; auth = <user>:<secret>@<realm>
; auth = <user>#<md5secret>@<realm>
; Example:
;auth=mark:topsecret@digium.com
;
; You may also add auth= statements to [peer] definitions
; Peer auth= override all other authentication settings if we match on realm
;------------------------------------------------------------------------------
; Users and peers have different settings available. Friends have all settings,
; since a friend is both a peer and a user
;
; User config options: Peer configuration:
; -------------------- -------------------
; context context
; callingpres callingpres
; permit permit
; deny deny
; secret secret
; md5secret md5secret
; dtmfmode dtmfmode
; canreinvite canreinvite
; nat nat
; callgroup callgroup
; pickupgroup pickupgroup
; language language
; allow allow
; disallow disallow
; insecure insecure
; trustrpid trustrpid
; progressinband progressinband
; promiscredir promiscredir
; useclientcode useclientcode
; accountcode accountcode
; setvar setvar
; callerid callerid
; amaflags amaflags
; call-limit call-limit
; restrictcid restrictcid
; allowoverlap allowoverlap
; allowsubscribe allowsubscribe
; subscribecontext subscribecontext
; videosupport videosupport
; maxcallbitrate maxcallbitrate
; mailbox
; username
; template
; fromdomain
; regexten
; fromuser
; host
; port
; qualify
; defaultip
; rtptimeout
; rtpholdtimeout
; sendrpid
;[sip_proxy]
; For incoming calls only. Example: FWD (Free World Dialup)
; We match on IP address of the proxy for incoming calls
; since we can not match on username (caller id)
;type=peer
;context=from-fwd
;host=fwd.pulver.com
;[sip_proxy-out]
;type=peer ; we only want to call out, not be called
;secret=guessit
;username=yourusername ; Authentication user for outbound proxies
;fromuser=yourusername ; Many SIP providers require this!
;fromdomain=provider.sip.domain
;host=box.provider.com
;usereqphone=yes ; This provider requires ";user=phone" on URI
;call-limit=5 ; permit only 5 simultaneous outgoing calls to this peer
; Call-limits will not be enforced on real-time peers,
; since they are not stored in-memory
;------------------------------------------------------------------------------
; Definitions of locally connected SIP devices
;
; type = user a device that authenticates to us by "from" field to place calls
; type = peer a device we place calls to or that calls us and we match by host
; type = friend two configurations (peer+user) in one
;
; For device names, we recommend using only a-z, numerics (0-9) and underscore
;
; For local phones, type=friend works most of the time
;
; If you have one-way audio, you propably have NAT problems.
; If Asterisk is on a public IP, and the phone is inside of a NAT device
; you will need to configure nat option for those phones.
; Also, turn on qualify=yes to keep the nat session open
;[grandstream1]
;type=friend
;context=from-sip ; Where to start in the dialplan when this phone calls
;callerid=John Doe <1234> ; Full caller ID, to override the phones config
; on incoming calls to Asterisk
;host=192.168.0.23 ; we have a static but private IP address
; No registration allowed
;nat=no ; there is not NAT between phone and Asterisk
;canreinvite=yes ; allow RTP voice traffic to bypass Asterisk
;dtmfmode=info ; either RFC2833 or INFO for the BudgeTone
;call-limit=1 ; permit only 1 outgoing call and 1 incoming call at a time
; from the phone to asterisk
; 1 for the explicit peer, 1 for the explicit user,
; remember that a friend equals 1 peer and 1 user in
; memory
; This will affect your subscriptions as well.
; There is no combined call counter for a "friend"
; so there's currently no way in sip.conf to limit
; to one inbound or outbound call per phone. Use
; the group counters in the dial plan for that.
;
;mailbox=1234@default ; mailbox 1234 in voicemail context "default"
;disallow=all ; need to disallow=all before we can use allow=
;allow=ulaw ; Note: In user sections the order of codecs
; listed with allow= does NOT matter!
;allow=alaw
;allow=g723.1 ; Asterisk only supports g723.1 pass-thru!
;allow=g729 ; Pass-thru only unless g729 license obtained
;astdb=chan2ext/SIP/grandstream1=1234 ; ensures an astDB entry exists
;callingpres=allowed_passed_screen ; Set caller ID presentation
; See README.callingpres for more information
;[xlite1]
; Turn off silence suppression in X-Lite ("Transmit Silence"=YES)!
; Note that Xlite sends NAT keep-alive packets, so qualify=yes is not needed
;type=friend
;regexten=1234 ; When they register, create extension 1234
;callerid="Jane Smith" <5678>
;host=dynamic ; This device needs to register
;nat=yes ; X-Lite is behind a NAT router
;canreinvite=no ; Typically set to NO if behind NAT
;disallow=all
;allow=gsm ; GSM consumes far less bandwidth than ulaw
;allow=ulaw
;allow=alaw
;mailbox=1234@default,1233@default ; Subscribe to status of multiple mailboxes
;[snom]
;type=friend ; Friends place calls and receive calls
;context=from-sip ; Context for incoming calls from this user
;secret=blah
;subscribecontext=localextensions ; Only allow SUBSCRIBE for local extensions
;language=de ; Use German prompts for this user
;host=dynamic ; This peer register with us
;dtmfmode=inband ; Choices are inband, rfc2833, or info
;defaultip=192.168.0.59 ; IP used until peer registers
;mailbox=1234@context,2345 ; Mailbox(-es) for message waiting indicator
;subscribemwi=yes ; Only send notifications if this phone
; subscribes for mailbox notification
;vmexten=voicemail ; dialplan extension to reach mailbox
; sets the Message-Account in the MWI notify message
; defaults to global vmexten which defaults to "asterisk"
;restrictcid=yes ; To have the callerid restriced -> sent as ANI
;disallow=all
;allow=ulaw ; dtmfmode=inband only works with ulaw or alaw!
;[polycom]
;type=friend ; Friends place calls and receive calls
;context=from-sip ; Context for incoming calls from this user
;secret=blahpoly
;host=dynamic ; This peer register with us
;dtmfmode=rfc2833 ; Choices are inband, rfc2833, or info
;username=polly ; Username to use in INVITE until peer registers
; Normally you do NOT need to set this parameter
;disallow=all
;allow=ulaw ; dtmfmode=inband only works with ulaw or alaw!
;progressinband=no ; Polycom phones don't work properly with "never"
;[pingtel]
;type=friend
;secret=blah
;host=dynamic
;insecure=port ; Allow matching of peer by IP address without
; matching port number
;insecure=invite ; Do not require authentication of incoming INVITEs
;insecure=port,invite ; (both)
;qualify=1000 ; Consider it down if it's 1 second to reply
; Helps with NAT session
; qualify=yes uses default value
;callgroup=1,3-4 ; We are in caller groups 1,3,4
;pickupgroup=1,3-5 ; We can do call pick-p for call group 1,3,4,5
;defaultip=192.168.0.60 ; IP address to use if peer has not registred
;[cisco1]
;type=friend
;secret=blah
;qualify=200 ; Qualify peer is no more than 200ms away
;nat=yes ; This phone may be natted
; Send SIP and RTP to the IP address that packet is
; received from instead of trusting SIP headers
;host=dynamic ; This device registers with us
;canreinvite=no ; Asterisk by default tries to redirect the
; RTP media stream (audio) to go directly from
; the caller to the callee. Some devices do not
; support this (especially if one of them is
; behind a NAT).
;defaultip=192.168.0.4 ; IP address to use until registration
;username=goran ; Username to use when calling this device before registration
; Normally you do NOT need to set this parameter
;setvar=CUSTID=5678 ; Channel variable to be set for all calls from this device
[asterlink]
type=friend
username=asdf
fromuser=asdf
fromdomain=asterlink.com
host=asterlink.com
secret=xxxxxxxxxx
sendrpid = yes
disallow=all
canreinvite=no
allow=ulaw
context=inbound-asterlink
insecure=very
dtmfmode=rfc2833