rendered paste bodyU-Boot 1.0.5
DRAM: 32 MB
relocate_code start
relocate code finish
Entering flash_init()
Flash: 8 MB
env_relocate[226] malloced ENV at 81f80008
env_relocate finished
entering devices_init
In: serial
Out: serial
Err: serial
console_init_r finished!
Net: danube Switch
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
## Booting image at b02d0000 ...
Image Name: MIPS Linux-2.4.31-Danube-3.0.3-G
Created: 2006-10-12 11:35:12 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 854782 Bytes = 834.7 kB
Load Address: 80002000
Entry Point: 801ca040
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
TODO: chip version
memsize=32l
flash_start=0xb0000000
flash_size=8388608l
Reserving memory for CP1 @0xa1f00000
memsize=31
CPU revision is: 00019641
Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Linux version 2.4.31-Danube-3.0.3-G0432V30V (root@localhost) (gcc version 3.3.6) #2 å10æ.. 12 19:35:05 CST 2006
Can't analyze prologue code at 8001e360
Determined physical RAM map:
User-defined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
On node 0 totalpages: 7936
zone(0): 7936 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 ip=10.10.10.10:10.10.10.123::::eth0:on console=ttyS1,115200 ethaddr=00:01:22:33:44:55 mem=31M panic=1
ethaddr_setup: mac address 0- 1-22-33-44-55
mips_hpt_frequency:166666667
r4k_offset: 00196e6a(1666666)
Using 166.667 MHz high precision timer.
Syam before calibrate_delay
Calibrating delay loop...
222.00 BogoMIPS
Syam after calibrate_delay
MIPS CPU counter frequency is fixed at 166666667 Hz
Memory: 28728k/31744k available (1808k kernel code, 3016k reserved, 108k data, 100k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Squashfs 2.2 (released 2005/07/03) (C) 2002-2004, 2005 Phillip Lougher
pty: 256 Unix98 ptys configured
ttyS0 at MEM 0xbe100400 (irq = 2) is a IFX_ASC
ttyS1 at MEM 0xbe100c00 (irq = 9) is a IFX_ASC
<6>Danube PMU driver v0.3
cgu: misc_register on minor = 63
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 62
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
led: misc_register on minor = 151
memcopy_init: memcopy init
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
danube MAC driver loaded!
Loading 2nd ETH driver... init succeeded
oamk: init_module() called.
Opening oam kernel socket
oamk: init_module() returned.
init_danube_mtd: start_scan_addr: b0000000
init_danube_mtd: chip probing count 0
Danube: probing address:b0000000
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
init_danube_mtd: bank1, name:Danube Bank 0, size:8388608bytes
DANUBE flash0: Using static image partition definition
Creating 7 MTD partitions on "Danube Bank 0":
0x00000000-0x00030000 : "U-Boot"
0x00030000-0x00050000 : "Environment"
0x00050000-0x002f0000 : "rootfs"
0x002f0000-0x003c0000 : "Linux"
0x003c0000-0x00400000 : "firmware"
0x00400000-0x00410000 : "User-Data"
0x00410000-0x00420000 : "voip-Data"
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
IP-Config: Guessing netmask 255.0.0.0
IP-Config: Complete:
device=eth0, addr=10.10.10.10, mask=255.0.0.0, gw=255.255.255.255,
host=10.10.10.10, domain=, nis-domain=(none),
bootserver=10.10.10.123, rootserver=10.10.10.123, rootpath=
ip_conntrack version 2.1 (248 buckets, 1984 max) - 624 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Ebtables v2.0 registered
NET4: Ethernet Bridge 008 for NET4.0
Bridge firewalling registered
Danube Port Initialization
DANUBE MIPS24KEc MPS mailbox driver, Version 1.1.0
(c) Copyright 2006, Infineon Technologies AG
IFX_MPS: using proc fs
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 100k freed
init started: BusyBox v1.00 (2006.10.12-11:36+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
Created character device /dev/danube-port with major[247] and minor[0]
1+0 records in
1+0 records out
Mount ADSL Firmware Now
part_begin_addr=0xb0400000
mtd_dev=/dev/mtd/5
autoboot open /dev/danube/mei fail
Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/net/ifx_nfext/ifx_nfext_core.o
Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/net/ifx_nfext/ifx_nfext_ppp.o
Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/drivers/net/admmod.o
Loading ADM6996 driver...
6996I SMI Mode-Chip ID:71023
Bringing up syslog
Bringing up klogd
<6>device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
--VDSL2 Pre Initialization --
Init VDSL2 CPE Ref environment
- loading VDSL2 CPE Ref Board - board driver -
*** Creating dir: /dev/adm5120_rb
*** Creating node: /dev/adm5120_rb/0
Using ./drv_adm5120_rb
ADM5120 Board Driver, Version 0.0.4.1
<6>(c) Copyright 2003, Infineon Technologies AG
- loading VDSL2 CPE board - DFE driver -
*** Creating dir: /dev/vinax
*** Creating node: /dev/vinax/cntrl0
*** Creating node: /dev/vinax/0
cat: /proc/mei/version: No such file or directory
3.0.3-432-V30WV
Using ./drv_vinax
<6>VINAX Driver, Version 0.1.0.2
<6>(c) Copyright 2005, Infineon Technologies AG
<6>### VINAX - VINAX - VINAX - VINAX ###
<7>VINAX_DRV: create proc config entry
--> Add VINAX tick to timer queue
board driver <drv_adm5120_rb> loaded
--> AInitializes the MultiPort Memory Controller for the VDSL2 DFEBoard_InitIrq!
mazon-Vinax test: open device: /dev/adm5120_rb/0.
--> Amazon-Vinax test: close(3) device: //dev/adm5120_rb/0.
current HW type is CPE_MODE
+++ setup CPE firmware vcpe_hw.bin +++
ln: ./firmware.bin: File exists
ln: ./firmware0.bin: File exists
ln: ./firmware1.bin: File exists
MEI driver <drv_vinax> loaded
init Danube-Vinax MEI base addr=0x14000000 poVINAX_DRV[00]: ERROR - INIT DEVICE, HW failure
lling mode
!!! RESET the VDSL2 device (via MEI) !!!
set VINAX DFE config
VDSL2 pre init done
---VDSL2 Post Initialization --
VDSL2 initialisation - post
Start VDSL2 CPE Ref environment
Start VINAX firmeware download
--> test: open device: /dev/vinax/0.
Start<7>VINAX_DRV[00-01] Error ioctl - missing init, invalid cmd !!!
Download <firmware.bin>, size: 540148
--> test: ERROR - ioct(FIO_VINAX_FW_DL), Operation not permitted, retCode = -1021
Start VDSL2 DSL DAEMON Application
DSL: start DSL daemon.
DSL: DSL daemon running in background now!
DSL: Device granularity is 1
DSL: No firmware pointer
DSL: No 2nd firmware pointer
DSL: Given warmstart memory will be analyzed...
<6>device nas1 entered promiscuous mode
br0: port 2(nas1) entering learning state
DSL: ...No warmstart memory defined
DSL: ...Using memory allocation via DSL_Malloc() for ALL data base sections
DSL: ...Startup mode: COLDSTART
DSL: No mapping information (line -> device channel) provided. Taking internal default settings.
DSL[00]: VINAX init failed, no valid data
DSL[00]: VINAX driver init failed
DSL:
DSL: *****************************************************
DSL: DSL library version: 1.5.1
DSL: *****************************************************
DSL: Number of devices : 1
DSL: Number of lines : 1
DSL: Number of lines/device : 1
DSL: Number of channels/line : 2
DSL:
DSL: Memory usage of warm start resistent data base
DSL: magic key data base : 4 bytes
DSL: line config data base : 316 bytes
DSL: channel config data base : 184 bytes
DSL: line array config data base : 2424 bytes
DSL: --------------
DSL: Total : 2928 bytes
DSL:
DSL: Memory usage of status data base
DSL: line status data base : 220 bytes
DSL: channel status data base : 408 bytes
DSL: --------------
DSL: Total : 628 bytes
DSL:
DSL: Context memory usage
DSL: context structure : 1128 bytes
DSL: Timeout event lists : 32 bytes
DSL: --------------
DSL: Total : 1160 bytes
DSL: *****************************************************
DSL:
DSL: Thread PID for thread tPM_Tick is 997
DSL: Thread PID for thread tPipe_0 is 1007
DSL: Thread PID for thread tPipe_1 is 1008
DSL: Thread PID for thread tPipe_2 is 1009
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
br0: port 2(nas1) entering forwarding state
br0: topology change detected, propagating
nReturn=0 nLine=0
VDSL2 post init done
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
installing mps devices...
+--------------------------------------+
| Linux/MIPS on DANUBE by Infineon COM AC BB_CPE |
+--------------------------------------+
br0: port 3(eth2) entering forwarding state
br0: topology change detected, propagating
danube login: