Mail version 8.1 6/6/93. Type ? for help.
"/var/spool/mail/root": 4 messages 4 unread
>U 1 root@localhost.local Mon May 29 01:56 30/1128 "SMART error (OfflineUncorrectableSector) detected on host: szand"
U 2 root@localhost.local Mon May 29 01:56 30/1131 "SMART error (CurrentPendingSector) detected on host: szandor"
U 3 root@localhost.local Mon May 29 03:01 39/1440 "LogWatch for szandor"
U 4 root@localhost.local Mon May 29 04:02 39/1440 "LogWatch for szandor"
& 1
Message 1:
From root@localhost.localdomain Mon May 29 01:56:35 2006
Date: Mon, 29 May 2006 01:56:11 +0300
From: root <root@localhost.localdomain>
To: root@localhost.localdomain
Subject: SMART error (OfflineUncorrectableSector) detected on host: szandor
This email was generated by the smartd daemon running on:
host name: szandor
DNS domain: [Unknown]
NIS domain: (none)
The following warning/error was logged by the smartd daemon:
Device: /dev/hda, 1 Offline uncorrectable sectors
For details see host's SYSLOG (default: /var/log/messages).
You can also use the smartctl utility for further investigation.
No additional email messages about this problem will be sent.
& 2
Message 2:
From root@localhost.localdomain Mon May 29 01:56:35 2006
Date: Mon, 29 May 2006 01:56:11 +0300
From: root <root@localhost.localdomain>
To: root@localhost.localdomain
Subject: SMART error (CurrentPendingSector) detected on host: szandor
This email was generated by the smartd daemon running on:
host name: szandor
DNS domain: [Unknown]
NIS domain: (none)
The following warning/error was logged by the smartd daemon:
Device: /dev/hda, 1 Currently unreadable (pending) sectors
For details see host's SYSLOG (default: /var/log/messages).
You can also use the smartctl utility for further investigation.
No additional email messages about this problem will be sent.
& 3
Message 3:
From root@localhost.localdomain Mon May 29 03:01:40 2006
Date: Mon, 29 May 2006 03:01:39 +0300
From: root <root@localhost.localdomain>
To: root@localhost.localdomain
Subject: LogWatch for szandor
################### LogWatch 7.1 (11/12/05) ####################
Processing Initiated: Mon May 29 03:01:39 2006
Date Range Processed: yesterday
( 2006-May-28 )
Period is day.
Detail Level of Output: 0
Type of Output: unformatted
Logfiles for Host: szandor
##################################################################
--------------------- Disk Space Begin ------------------------
Filesystem Size Used Avail Use% Mounted on
/dev/hda2 8.6G 3.6G 4.7G 44% /
---------------------- Disk Space End -------------------------
###################### LogWatch End #########################
/var/log/messages
__________________________________________________
May 29 01:56:10 szandor kernel: SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
May 29 01:56:10 szandor smartd[1513]: smartd version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
May 29 01:56:10 szandor smartd[1513]: Home page is http://smartmontools.sourceforge.net/
May 29 01:56:10 szandor smartd[1513]: Opened configuration file /etc/smartd.conf
May 29 01:56:10 szandor smartd[1513]: Configuration file /etc/smartd.conf parsed.
May 29 01:56:10 szandor smartd[1513]: Device: /dev/hda, opened
May 29 01:56:10 szandor smartd[1513]: Device: /dev/hda, found in smartd database.
May 29 01:56:10 szandor smartd[1513]: Device: /dev/hda, is SMART capable. Adding to "monitor" list.
May 29 01:56:10 szandor smartd[1513]: Monitoring 1 ATA and 0 SCSI devices
May 29 01:56:11 szandor smartd[1513]: Device: /dev/hda, 1 Currently unreadable (pending) sectors
May 29 01:56:11 szandor smartd[1513]: Sending warning via mail to root ...
May 29 01:56:11 szandor smartd[1513]: Warning via mail to root: successful
May 29 01:56:11 szandor smartd[1513]: Device: /dev/hda, 1 Offline uncorrectable sectors
May 29 01:56:11 szandor smartd[1513]: Sending warning via mail to root ...
May 29 01:56:11 szandor smartd[1513]: Warning via mail to root: successful
May 29 01:56:11 szandor smartd[1521]: smartd has fork()ed into background mode. New PID=1521.
May 29 01:56:11 szandor hpiod: 0.9.8 accepting connections at 50000...
May 29 01:56:13 szandor kernel: ppdev: user-space parallel port driver
May 29 01:56:14 szandor hpiod: ParDevice::nibble_read failed: Input/output error
May 29 01:56:34 szandor gpm[1632]: *** info [startup.c(95)]:
May 29 01:56:34 szandor gpm[1632]: Started gpm successfully. Entered daemon mode.
_______________________________
-only configuration source at position 0
May 29 02:27:08 szandor gconfd (nuambenzina-3562): Resolved address "xml:readwrite:/home/nuambenzina/.gconf" to a writable
configuration source at position 1
May 29 02:27:08 szandor gconfd (nuambenzina-3562): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-
only configuration source at position 2
May 29 02:56:12 szandor smartd[1521]: Device: /dev/hda, 1 Currently unreadable (pending) sectors
May 29 02:56:12 szandor smartd[1521]: Device: /dev/hda, 1 Offline uncorrectable sectors
May 29 03:26:11 szandor smartd[1521]: Device: /dev/hda, 1 Currently unreadable (pending) sectors
May 29 03:26:11 szandor smartd[1521]: Device: /dev/hda, 1 Offline uncorrectable sectors
May 29 03:56:11 szandor smartd[1521]: Device: /dev/hda, 1 Currently unreadable (pending) sectors
May 29 03:56:11 szandor smartd[1521]: Device: /dev/hda, 1 Offline uncorrectable sectors
Use smartctl -h to get a usage summary
[root@szandor ~]# smartctl -h
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Usage: smartctl [options] device
============================================ SHOW INFORMATION OPTIONS =====
-h, --help, --usage
Display this help and exit
-V, --version, --copyright, --license
Print license, copyright, and version information and exit
-i, --info
Show identity information for device
-a, --all
Show all SMART information for device
================================== SMARTCTL RUN-TIME BEHAVIOR OPTIONS =====
-q TYPE, --quietmode=TYPE (ATA)
Set smartctl quiet mode to one of: errorsonly, silent
-d TYPE, --device=TYPE
Specify device type to one of: ata, scsi, marvell, 3ware,N
-T TYPE, --tolerance=TYPE (ATA)
Tolerance: normal, conservative, permissive, verypermissive
-b TYPE, --badsum=TYPE (ATA)
Set action on bad checksum to one of: warn, exit, ignore
-r TYPE, --report=TYPE
Report transactions (see man page)
============================== DEVICE FEATURE ENABLE/DISABLE COMMANDS =====
-s VALUE, --smart=VALUE
Enable/disable SMART on device (on/off)
-o VALUE, --offlineauto=VALUE (ATA)
Enable/disable automatic offline testing on device (on/off)
-S VALUE, --saveauto=VALUE (ATA)
Enable/disable Attribute autosave on device (on/off)
======================================= READ AND DISPLAY DATA OPTIONS =====
-H, --health
Show device SMART health status
-c, --capabilities (ATA)
Show device SMART capabilities
-A, --attributes
Show device SMART vendor-specific Attributes and values
-l TYPE, --log=TYPE
Show device log. TYPE: error, selftest, selective, directory
-v N,OPTION , --vendorattribute=N,OPTION (ATA)
Set display OPTION for vendor Attribute N (see man page)
-F TYPE, --firmwarebug=TYPE (ATA)
Use firmware bug workaround: none, samsung, samsung2
-P TYPE, --presets=TYPE (ATA)
Drive-specific presets: use, ignore, show, showall
============================================ DEVICE SELF-TEST OPTIONS =====
-t TEST, --test=TEST
Run test. TEST is: offline short long conveyance select,M-N pending,N afterselect,on afterselect,off
-C, --captive
Do test in captive mode (along with -t)
-X, --abort
Abort any non-captive test on device
=================================================== SMARTCTL EXAMPLES =====
smartctl -a /dev/hda (Prints all SMART information)
smartctl --smart=on --offlineauto=on --saveauto=on /dev/hda
(Enables SMART on first disk)
smartctl -t long /dev/hda (Executes extended disk self-test)
smartctl --attributes --log=selftest --quietmode=errorsonly /dev/hda
(Prints Self-Test & Attribute errors)
smartctl -a --device=3ware,2 /dev/sda
(Prints all SMART info for 3rd ATA disk on 3ware RAID controller)
[root@szandor ~]# smartctl -a /dev/hda
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3120026A
Serial Number: 5JT2J6E8
Firmware Version: 3.06
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Mon May 29 04:23:47 2006 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 063 056 006 Pre-fail Always - 25009039
3 Spin_Up_Time 0x0003 099 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 525
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always - 8972137004
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10341
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 2037
194 Temperature_Celsius 0x0022 039 053 000 Old_age Always - 39
195 Hardware_ECC_Recovered 0x001a 063 056 000 Old_age Always - 25009039
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 162 000 Old_age Always - 326
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 294 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 294 occurred at disk power-on lifetime: 10281 hours (428 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f5 c3 30 e0 Error: UNC at LBA = 0x0030c3f5 = 3195893
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 08 ef c3 30 e0 00 00:06:37.394 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:37.393 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:37.381 READ DMA
c8 d8 08 df c3 30 e0 00 00:06:37.369 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:33.383 READ DMA
Error 293 occurred at disk power-on lifetime: 10281 hours (428 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f5 c3 30 e0 Error: UNC at LBA = 0x0030c3f5 = 3195893
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 38 df c3 30 e0 00 00:06:28.553 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:28.544 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:28.524 READ DMA
c8 d8 20 46 d5 49 e0 00 00:06:28.524 READ DMA
c8 d8 01 00 00 00 e0 00 00:06:33.383 READ DMA
Error 292 occurred at disk power-on lifetime: 10281 hours (428 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f5 c3 30 e0 Error: UNC at LBA = 0x0030c3f5 = 3195893
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 08 ef c3 30 e0 00 00:06:28.553 READ DMA
c8 d8 08 67 d7 30 e0 00 00:06:28.544 READ DMA
c8 d8 08 a7 80 30 e0 00 00:06:28.524 READ DMA
c8 d8 08 e7 c3 30 e0 00 00:06:28.524 READ DMA
c8 d8 08 ef e4 2f e0 00 00:06:28.510 READ DMA
Error 291 occurred at disk power-on lifetime: 9698 hours (404 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 bf cb 3e e1 Error: ICRC, ABRT 1 sectors at LBA = 0x013ecbbf = 20892607
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 03 08 b8 cb 3e e1 00 00:01:12.690 READ DMA
c8 03 08 d8 31 20 e1 00 00:01:12.676 READ DMA
c8 03 08 d0 31 20 e1 00 00:01:12.737 READ DMA
c8 03 08 d8 33 1e e1 00 00:01:12.736 READ DMA
c8 03 08 d0 33 1e e1 00 00:01:12.730 READ DMA
Error 290 occurred at disk power-on lifetime: 9698 hours (404 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 97 f8 fc e0 Error: ICRC, ABRT at LBA = 0x00fcf897 = 16578711
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 97 f8 fc e0 00 00:10:13.365 READ DMA EXT
25 00 00 97 f8 fc e0 00 00:10:13.361 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:10:13.349 RECALIBRATE [OBS-4]
25 00 00 97 f8 fc e0 00 00:10:13.344 READ DMA EXT
25 00 00 97 f8 fc e0 00 00:10:13.337 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 90% 8755 -
# 2 Short offline Completed without error 00% 6380 -
# 3 Short offline Aborted by host 70% 6380 -
# 4 Short offline Completed without error 00% 3275 -
# 5 Short offline Completed without error 00% 3037 -
# 6 Short offline Completed without error 00% 2817 -
# 7 Short offline Completed without error 00% 2785 -
# 8 Extended offline Interrupted (host reset) 60% 2785 -
# 9 Short offline Completed without error 00% 2785 -
#10 Short offline Completed without error 00% 2740 -
#11 Short offline Completed without error 00% 1778 -
#12 Short offline Completed without error 00% 1769 -
#13 Extended offline Interrupted (host reset) 90% 859 -
#14 Short offline Completed without error 00% 859 -
#15 Short offline Completed without error 00% 859 -
#16 Short offline Completed without error 00% 769 -
#17 Short offline Completed without error 00% 769 -
#18 Short offline Completed without error 00% 202 -
#19 Short offline Completed without error 00% 51 -
#20 Short offline Aborted by host 50% 51 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@szandor ~]# smartctl -h
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Usage: smartctl [options] device
============================================ SHOW INFORMATION OPTIONS =====
-h, --help, --usage
Display this help and exit
-V, --version, --copyright, --license
Print license, copyright, and version information and exit
-i, --info
Show identity information for device
-a, --all
Show all SMART information for device
================================== SMARTCTL RUN-TIME BEHAVIOR OPTIONS =====
-q TYPE, --quietmode=TYPE (ATA)
Set smartctl quiet mode to one of: errorsonly, silent
-d TYPE, --device=TYPE
Specify device type to one of: ata, scsi, marvell, 3ware,N
-T TYPE, --tolerance=TYPE (ATA)
Tolerance: normal, conservative, permissive, verypermissive
-b TYPE, --badsum=TYPE (ATA)
Set action on bad checksum to one of: warn, exit, ignore
-r TYPE, --report=TYPE
Report transactions (see man page)
============================== DEVICE FEATURE ENABLE/DISABLE COMMANDS =====
-s VALUE, --smart=VALUE
Enable/disable SMART on device (on/off)
-o VALUE, --offlineauto=VALUE (ATA)
Enable/disable automatic offline testing on device (on/off)
-S VALUE, --saveauto=VALUE (ATA)
Enable/disable Attribute autosave on device (on/off)
======================================= READ AND DISPLAY DATA OPTIONS =====
-H, --health
Show device SMART health status
-c, --capabilities (ATA)
Show device SMART capabilities
-A, --attributes
Show device SMART vendor-specific Attributes and values
-l TYPE, --log=TYPE
Show device log. TYPE: error, selftest, selective, directory
-v N,OPTION , --vendorattribute=N,OPTION (ATA)
Set display OPTION for vendor Attribute N (see man page)
-F TYPE, --firmwarebug=TYPE (ATA)
Use firmware bug workaround: none, samsung, samsung2
-P TYPE, --presets=TYPE (ATA)
Drive-specific presets: use, ignore, show, showall
============================================ DEVICE SELF-TEST OPTIONS =====
-t TEST, --test=TEST
Run test. TEST is: offline short long conveyance select,M-N pending,N afterselect,on afterselect,off
-C, --captive
Do test in captive mode (along with -t)
-X, --abort
Abort any non-captive test on device
=================================================== SMARTCTL EXAMPLES =====
smartctl -a /dev/hda (Prints all SMART information)
smartctl --smart=on --offlineauto=on --saveauto=on /dev/hda
(Enables SMART on first disk)
smartctl -t long /dev/hda (Executes extended disk self-test)
smartctl --attributes --log=selftest --quietmode=errorsonly /dev/hda
(Prints Self-Test & Attribute errors)
smartctl -a --device=3ware,2 /dev/sda
(Prints all SMART info for 3rd ATA disk on 3ware RAID controller)
[root@szandor ~]# smartctl -H /dev/hda
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
[root@szandor ~]# smartctl -t /dev/hda
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=======> INVALID ARGUMENT TO -t: /dev/hda
=======> VALID ARGUMENTS ARE: offline, short, long, conveyance, select,M-N, pending,N, afterselect,on, afterselect,off <=======
Use smartctl -h to get a usage summary
[root@szandor ~]# smartctl -t long /dev/hda
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 85 minutes for test to complete.
Test will complete after Mon May 29 05:53:04 2006
Use smartctl -X to abort test.
[root@szandor ~]#