rendered paste bodyLinux version 2.6.22-rc4 (root@debian) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #3 SMP Sat Jun 9 13:41:36 CEST 2007
Command line: root=/dev/sda1 ro
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 524208) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000FB050, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFB0000, 0038 (r1 A M I OEMRSDT 2000706 MSFT 97)
ACPI: FACP 7FFB0200, 0084 (r2 A M I OEMFACP 12000601 MSFT 97)
ACPI: DSDT 7FFB0440, 4DB1 (r1 ASR19 ASR19101 101 INTL 20051117)
ACPI: FACS 7FFC0000, 0040
ACPI: APIC 7FFB0390, 0070 (r1 A M I OEMAPIC 2000706 MSFT 97)
ACPI: MCFG 7FFB0400, 003C (r1 A M I OEMMCFG 2000706 MSFT 97)
ACPI: OEMB 7FFC0040, 0060 (r1 A M I AMI_OEM 2000706 MSFT 97)
ACPI: SSDT 7FFB5200, 01C4 (r1 A M I POWERNOW 1 AMD 1)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-000000007ffb0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 524208) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007ffb0000
No mptable found.
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524208
On node 0 totalpages: 524111
DMA zone: 56 pages used for memmap
DMA zone: 1150 pages reserved
DMA zone: 2793 pages, LIFO batch:0
DMA32 zone: 7110 pages used for memmap
DMA32 zone: 513002 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x2008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e8000
swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37000 bytes of per cpu data
Built 1 zonelists. Total pages: 515795
Kernel command line: root=/dev/sda1 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2009.183 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
CPU 0: aperture @ 2020000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2057884k/2096832k available (2534k kernel code, 38560k reserved, 1058k data, 332k init)
Calibrating delay using timer specific routine.. 4022.48 BogoMIPS (lpj=8044978)
Security Framework v1.0.0 initialized
Capability LSM initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12557393
Detected 12.557 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4018.61 BogoMIPS (lpj=8037223)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
Brought up 2 CPUs
migration_cost=92
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0510
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0401
pnp: ACPI device : hid PNPB006
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0F03
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
irda_init()
NET: Registered protocol family 23
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: 00:09: iomem range 0x0-0x0 could not be reserved
pnp: 00:09: iomem range 0xfee01000-0xfeefffff has been reserved
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: match found with the PnP device '00:0e' and the driver 'system'
pnp: 00:0e: ioport range 0x290-0x29f has been reserved
pnp: match found with the PnP device '00:0f' and the driver 'system'
pnp: 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
pnp: match found with the PnP device '00:10' and the driver 'system'
pnp: 00:10: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:10: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:10: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:10: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:08.0
IO window: disabled.
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
IO window: d000-dfff
MEM window: fe900000-fe9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: e000-efff
MEM window: feb00000-febfffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5082k freed
audit: initializing netlink socket (disabled)
audit(1182320006.484:1): initialized
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:04:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0d' and the driver 'serial'
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
usbmon: debugfs is not available
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:0c' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 332k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe8ff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 22, io mem 0xfe8fec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:01:00.0 to 64
eth0: RTL8168b/8111b at 0xffffc20000aae000, 00:19:66:13:f4:73, IRQ 19
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKD] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8]
pata_amd 0000:00:09.0: version 0.3.8
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001ffa0 irq 14
ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001ffa8 irq 15
ATA: abnormal status 0x8 on port 0x00000000000101f7
ATA: abnormal status 0x8 on port 0x00000000000101f7
ata1.01: ATAPI, max UDMA/33
ata1.01: configured for UDMA/33
ata2: port disabled. ignoring.
scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
ahci 0000:00:0a.0: version 2.2
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 21 (level, low) -> IRQ 21
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg0 type 5
ieee1394: Host added: ID:BUS[0-00:1023] GUID[008f1300adfa0100]
ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:0a.0: flags: 64bit led clo pmp pio
PCI: Setting latency timer of device 0000:00:0a.0 to 64
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 cmd 0xffffc20000ae4100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata4: SATA max UDMA/133 cmd 0xffffc20000ae4180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata5: SATA max UDMA/133 cmd 0xffffc20000ae4200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata6: SATA max UDMA/133 cmd 0xffffc20000ae4280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ata_hpa_resize 1: sectors = 488397168, hpa_sectors = 488397168
ata3.00: ATA-7: SAMSUNG SP2504C, VT100-50, max UDMA7
ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: ata_hpa_resize 1: sectors = 488397168, hpa_sectors = 488397168
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
scsi 2:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 >
sd 2:0:0:0: [sda] Attached SCSI disk
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2d00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2e00
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[B] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
input: ImExPS/2 Logitech Wheel Mouse as /class/input/input1
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:07' and the driver 'parport_pc'
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
pnp: the driver 'mpu401' has been registered
pnp: match found with the PnP device '00:08' and the driver 'mpu401'
Adding 6032368k swap on /dev/sda5. Priority:-1 extents:1 across:6032368k
EXT3 FS on sda1, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
fuse init (API version 7.8)
r8169: eth1: link up
r8169: eth1: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
eth1: no IPv6 routers present
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 1887 MBytes.
[fglrx] module loaded - fglrx 8.37.6 [May 25 2007] on minor 0
ACPI: PCI Interrupt Link [LNED] enabled at IRQ 17
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 17 (level, low) -> IRQ 17
[fglrx] total GART = 130023424
[fglrx] free GART = 114032640
[fglrx] max single GART = 114032640
[fglrx] total LFB = 134086656
[fglrx] free LFB = 115871744
[fglrx] max single LFB = 115871744
[fglrx] total Inv = 0
[fglrx] free Inv = 0
[fglrx] max single Inv = 0
[fglrx] total TIM = 0
r8169: eth1: link up
eth1: no IPv6 routers present
usb 2-2: new high speed USB device using ehci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice