rendered paste body
/etc/zaptel.conf:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
# Autogenerated by /usr/local/sbin/sangoma/setup-sangoma -- do not hand edit
# Zaptel Channels Configurations (zaptel.conf)
#
loadzone=us
defaultzone=us
#Sangoma A101 port 1 [slot:2 bus:4 span: 1]
span=1,0,0,esf,b8zs
bchan=1-23
dchan=24
/etc/asterisk/zapata.conf:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
;
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-auto.conf
;Include AMP configs
#include zapata_additional.conf
/etc/asterisk/zapata-auto.conf:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
; Autogenerated by /usr/local/sbin/sangoma/setup-sangoma -- do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
callerid=asreceived
;Sangoma A101 port 1 [slot:2 bus:4 span: 1]
switchtype=national
context=from-pstn
group=0
signalling=pri_cpe
channel => 1-23
/etc/wanpipe/wanpipe1.conf:::::::::::::::::::::::::::::::::::::::::::::::::::::::::
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 2
PCIBUS = 4
FE_MEDIA = T1
FE_LCODE = B8ZS
FE_FRAME = ESF
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
TE_HIGHIMPEDANCE = NO
LBO = 0DB
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 24
[w1g1]
ACTIVE_CH = ALL
TDMV_ECHO_OFF = NO
TDMV_HWEC = NO
###########/var/log/wanrouter::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
Wed May 30 05:01:32 PDT 2007: starting WAN router
Starting up device: wanpipe1
WAN Router Configurator(c) 1995-2003 Sangoma Technologies Inc.
* Parsing configuration file /etc/wanpipe/wanpipe1.conf ...
* Reading section [devices]...
* Reading section [wanpipe1]...
* Reading section [interfaces]...
* w1g1 to used by TDM_VOICE
* Reading section [w1g1]...
* Configuring device wanpipe1 (no description)
* Setting CARD_TYPE to AFT
* Setting S514CPU to A
* Setting COMMPORT to PRI
* Setting AUTO_PCISLOT to NO
* Setting PCISLOT to 2
* Setting PCIBUS to 4
* Setting FE_MEDIA to T1
* Setting FE_LCODE to B8ZS
* Setting FE_FRAME to ESF
* Setting FE_LINE to 1
* Setting TE_CLOCK to NORMAL
* Setting TE_REF_CLOCK to 0
* Setting TE_HIGHIMPEDANCE to NO
* Setting LBO to 0DB
* Setting FE_TXTRISTATE to NO
* Setting MTU to 1500
* Setting UDPPORT to 9000
* Setting TTL to 255
* Setting IGNORE_FRONT_END to NO
* Setting TDMV_SPAN to 1
* Setting TDMV_DCHAN to 24
###########/var/log/messages::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
May 30 04:58:59 localhost kernel: WANPIPE(tm) WANEC Layer Stable 2.3.4-7 (c) 1995-2006 Sangoma Technologies Inc.
May 30 04:58:59 localhost kernel: wanec_create_dev: Registering Wanpipe ECDEV Device!
May 30 04:58:59 localhost kernel: wanpipe1: Starting WAN Setup
May 30 04:58:59 localhost kernel:
May 30 04:58:59 localhost kernel: Processing WAN device wanpipe1...
May 30 04:58:59 localhost kernel: wanpipe1: Locating: A102/2D/4/4D/8 card, CPU A, PciSlot=2, PciBus=4
May 30 04:58:59 localhost kernel: wanpipe1: Error, A102/2D/4/4D/8 card not found on bus #4, slot #2, cpu A, line 1
May 30 05:00:00 localhost kernel: af_wanpipe: Unregistering Wanpipe API Socket Module
May 30 05:00:00 localhost kernel: NET: Unregistered protocol family 25
May 30 05:00:00 localhost kernel: wanec_remove_dev: Unregistering Wanpipe ECDEV Device!
May 30 05:00:00 localhost kernel: WANEC Layer: Unloaded
May 30 05:00:00 localhost kernel: WANPIPE L.I.P: Unloaded
May 30 05:00:00 localhost kernel:
May 30 05:00:00 localhost kernel: wanpipe: WANPIPE Modules Unloaded.
May 30 05:00:08 localhost zaptel: Unloading ztdummy: succeeded
May 30 05:00:08 localhost zaptel: Unloading wctdm: succeeded
May 30 05:00:08 localhost zaptel: Unloading wcfxo: succeeded
May 30 05:00:08 localhost zaptel: Unloading wcte11xp: succeeded
May 30 05:00:08 localhost zaptel: Unloading wct1xxp: succeeded
May 30 05:00:08 localhost zaptel: Unloading wct4xxp: succeeded
May 30 05:00:08 localhost kernel: Unregistered Tormenta2
May 30 05:00:08 localhost zaptel: Unloading tor2: succeeded
May 30 05:00:08 localhost kernel: Zapata Telephony Interface Unloaded
May 30 05:00:08 localhost zaptel: Removing zaptel module: succeeded
May 30 05:00:37 localhost kernel: sdladrv: No versions for exported symbols. Tainting kernel.
May 30 05:00:37 localhost kernel: WANPIPE(tm) Hardware Support Module Stable 2.3.4-7 (c) 1994-2007 Sangoma Technologies Inc
May 30 05:00:37 localhost kernel: Zapata Telephony Interface Registered on major 196
May 30 05:00:37 localhost kernel: Zaptel Version: Echo Canceller: KB1
May 30 05:00:37 localhost kernel: wanrouter: No versions for exported symbols. Tainting kernel.
May 30 05:00:37 localhost kernel: WANPIPE(tm) Interface Support Module Stable 2.3.4-7 (c) 1994-2007 Sangoma Technologies Inc
May 30 05:00:38 localhost kernel: WANPIPE(tm) Multi-Protocol WAN Driver Module Stable 2.3.4-7 (c) 1994-2007 Sangoma Technologies Inc
May 30 05:00:38 localhost kernel: wanpipe: Probing for WANPIPE hardware.
May 30 05:00:38 localhost kernel: ACPI: PCI interrupt 0000:04:02.0[A] -> GSI 52 (level, low) -> IRQ 201
May 30 05:00:38 localhost kernel: wanpipe: AFT-A101-SH T1/E1 card found (HDLC (DS) rev.29), cpu(s) 1, bus #4, slot #2, irq #201
May 30 05:00:38 localhost kernel: wanpipe: Allocating maximum 1 devices: wanpipe1 - wanpipe1.
May 30 05:00:38 localhost kernel: WANPIPE: TDM Codecs Initialized
May 30 05:00:38 localhost kernel: WANPIPE(tm) Socket API Module Stable 2.3.4-7 (c) 1994-2007 Sangoma Technologies Inc
May 30 05:00:38 localhost kernel: NET: Registered protocol family 25
May 30 05:00:38 localhost kernel: WANPIPE(tm) L.I.P Network Layer Stable 2.3.4-7 (c) 1995-2004 Sangoma Technologies Inc.
May 30 05:00:38 localhost kernel: WanpipeLIP: Protocols: No Protocol Compiled
May 30 05:00:38 localhost kernel:
May 30 05:00:38 localhost kernel: WANPIPE(tm) WANEC Layer Stable 2.3.4-7 (c) 1995-2006 Sangoma Technologies Inc.
May 30 05:00:38 localhost kernel: wanec_create_dev: Registering Wanpipe ECDEV Device!
May 30 05:01:32 localhost kernel: wanpipe1: Starting WAN Setup
May 30 05:01:32 localhost kernel:
May 30 05:01:32 localhost kernel: Processing WAN device wanpipe1...
May 30 05:01:32 localhost kernel: wanpipe1: Locating: A102/2D/4/4D/8 card, CPU A, PciSlot=2, PciBus=4
May 30 05:01:32 localhost kernel: wanpipe1: Error, A102/2D/4/4D/8 card not found on bus #4, slot #2, cpu A, line 1
#################################More Stuff::::::::::::::::::::::::::::::::::::::::::::::::::::::::
[root@localhost ~]# wancfg
Failed to read 'WAN_BIN_DIR' in 'wanrouter.rc'! Using default: '/usr/sbin'.
****** Reading section [devices]...
****** Reading section [wanpipe1]...
* Setting CARD_TYPE to AFT
* Setting S514CPU to A
* Setting COMMPORT to PRI
* Setting AUTO_PCISLOT to NO
* Setting PCISLOT to 2
* Setting PCIBUS to 4
* Setting FE_MEDIA to T1
* Setting FE_LCODE to B8ZS
* Setting FE_FRAME to ESF
* Setting FE_LINE to 1
* Setting TE_CLOCK to NORMAL
* Setting TE_REF_CLOCK to 0
* Setting TE_HIGHIMPEDANCE to NO
* Setting LBO to 0DB
* Setting FE_TXTRISTATE to NO
* Setting MTU to 1500
* Setting UDPPORT to 9000
* Setting TTL to 255
* Setting IGNORE_FRONT_END to NO
* Setting TDMV_SPAN to 1
* Setting TDMV_DCHAN to 24
****** Reading section [interfaces]...
****** Reading section [w1g1]...
* Setting ACTIVE_CH to ALL
* Setting TDMV_ECHO_OFF to NO
* Setting TDMV_HWEC to NO
[root@localhost ~]# service wanrouter start
Starting WAN Router...
Starting up device: wanpipe1
wanconfig: WAN device wanpipe1 driver load failed !!
: ioctl(wanpipe1,ROUTER_SETUP) failed:
: 22 - Invalid argument
Wanpipe driver did not load properly
Please check /var/log/wanrouter and
/var/log/messages for errors
Configuring interfaces: w1g1 w1g1: unknown interface: No such device
done.
Zaptel Configuration
======================
SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: Clear channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: D-channel (Default) (Slaves: 24)
24 channels configured.
ZT_SPANCONFIG failed on span 1: No such device or address (6)
[root@localhost ~]# lspci
00:00.0 Host bridge: Intel Corporation E7501 Memory Controller Hub (rev 01)
00:00.1 Class ff00: Intel Corporation E7500/E7501 Host RASUM Controller (rev 01)
00:03.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface C PCI-to-PCI Bridge (rev 01)
00:03.1 Class ff00: Intel Corporation E7500/E7501 Hub Interface C RASUM Controller (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CA LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CA Ultra ATA Storage Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
01:03.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0d)
01:04.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
01:08.0 Communication controller: Conexant: Unknown device 10b4 (rev 89)
01:0c.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
02:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04)
02:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev 04)
02:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04)
02:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev 04)
03:03.0 SCSI storage controller: Adaptec AIC-7901A U320 (rev 03)
04:02.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card