rendered paste body<4>get_mask 0x00000000, set_mask 0x00000000 - after update
<4>rates_basic:0003->03, rates_supported:0127->1F
<4>BSS_Type = 0
<4>JoinBSSID MAC:7E:CB:56:BE:41:24
<4>acx_i_timer: adev->status=4 (ASSOCIATED)
<6>NETDEV WATCHDOG: wlan0: transmit timed out
<4>wlan0: FAILED to free any of the many full tx buffers. Switching to emergency freeing. Please report!
<4>wlan0: tx timeout!
<4>wlan0: less than 5 minutes since last radio recalibration, not recalibrating (maybe card is too hot?)
<4>wlan0: tx error 0x20, buf 10! (excessive Tx retries due to either distance too high or unable to Tx or Tx frame error - try changing 'iwconfig txpower XXX' or 'sens'itivity or 'retry')
<4>wlan0: tx error 0x20, buf 03! (excessive Tx retries due to either distance too high or unable to Tx or Tx frame error - try changing 'iwconfig txpower XXX' or 'sens'itivity or 'retry')
<4>wlan0: tx error 0x20, buf 07! (excessive Tx retries due to either distance too high or unable to Tx or Tx frame error - try changing 'iwconfig txpower XXX' or 'sens'itivity or 'retry')
<4>wlan0: several excessive Tx retry errors occurred, attempting to recalibrate radio. Radio drift might be caused by increasing card temperature, please check the card before it's too late!
<4>wlan0: tx error 0x20, buf 13! (excessive Tx retries due to either distance too high or unable to Tx or Tx frame error - try changing 'iwconfig txpower XXX' or 'sens'itivity or 'retry')
<4>wlan0: successfully recalibrated radio
<4>Stopping tasks ... done.
<4>Suspending console(s)
<4>acx: suspend handler is experimental!
<4>sus: dev c323c000
<4>sus: adev c323c340
<4>acx_set_status(0):STOPPED
<4>rx3000_wlan_stop
<7>udc: pullup(2)
<7>suspending dma channel 0
<7>suspending dma channel 1
<7>suspending dma channel 2
<7>suspending dma channel 3
<7>saved f0000008 value 2de23d00
<7>saved f000001c value 000000be
<7>saved f64000c4 value 00000000
<7>saved f64000c8 value 00000000
<7>saved f64000d4 value 00000000
<7>saved f64000d0 value 01555555
<7>saved f64000d8 value 00001fff
<7>s3c2410_pm_enter(3)
<7>s3c2410_sleep_save_phys=0x332f7e50
<7>saved f6400000 value 005f3726
<7>saved f6400004 value 0020c851
<7>saved f6400010 value 00155505
<7>saved f6400014 value 000004a8
<7>saved f6400018 value 000007ff
<7>saved f6400020 value aa955595
<7>saved f6400024 value 00000000
<7>saved f6400028 value 0000ffff
<7>saved f6400030 value aa95aaa1
<7>saved f6400034 value 00000000
<7>saved f6400038 value 0000ffff
<7>saved f6400040 value a5555555
<7>saved f6400044 value 00000800
<7>saved f6400048 value 0000ffff
<7>saved f6400050 value 0000a82a
<7>saved f6400054 value 00000097
<7>saved f6400058 value 000000ff
<7>saved f6400060 value 01aaaaa2
<7>saved f6400064 value 000033cf
<7>saved f6400068 value 0000ffff
<7>saved f6400070 value 0014aaaa
<7>saved f6400074 value 000003bf
<7>saved f6400078 value 000006ff
<7>saved f6400084 value 00000000
<7>saved f0200000 value 00ffffff
<7>saved f020000c value 00007da0
<7>saved f0100000 value 22651550
<7>saved f0100004 value 00000700
<7>saved f0100008 value 000057a4
<7>saved f010000c value 000057a4
<7>saved f0100010 value 00000700
<7>saved f0100014 value 000057a4
<7>saved f0100018 value 000057a4
<7>saved f0200014 value 00000007
<7>saved f0200004 value 0006e031
<7>saved f0200008 value 0003c042
<7>saved f0200010 value 00000004
<7>saved f0100024 value 00ac03f2
<7>Leaving IRQ 16 (pin 160) enabled
<7>Disabling IRQ 17 (pin 161)
<7>Disabling IRQ 18 (pin 162)
<7>Disabling IRQ 49 (pin 165)
<7>Disabling IRQ 50 (pin 166)
<7>Disabling IRQ 51 (pin 167)
<7>Disabling IRQ 52 (pin 192)
<7>Disabling IRQ 54 (pin 194)
<7>Disabling IRQ 55 (pin 195)
<7>Disabling IRQ 56 (pin 196)
<7>Disabling IRQ 57 (pin 197)
<7>Disabling IRQ 58 (pin 198)
<7>Disabling IRQ 59 (pin 199)
<7>sleep: irq wakeup masks: fffffffe,ffffffff
<7>GSTATUS3 0x3030b0f8
<7>GSTATUS4 0x00000000
<7>restore f6400000 (restore 005f3726, was 005f3726)
<7>restore f6400004 (restore 0020c851, was 0020c850)
<7>restore f6400010 (restore 00155505, was 00155405)
<7>restore f6400014 (restore 000004a8, was 000006e8)
<7>restore f6400018 (restore 000007ff, was 000007ff)
<7>restore f6400020 (restore aa955595, was aa901659)
<7>restore f6400024 (restore 00000000, was 00000000)
<7>restore f6400028 (restore 0000ffff, was 0000fcff)
<7>restore f6400030 (restore aa95aaa1, was aa81aaa1)
<7>restore f6400034 (restore 00000000, was 00000000)
<7>restore f6400038 (restore 0000ffff, was 0000fbff)
<7>restore f6400040 (restore a5555555, was 54555555)
<7>restore f6400044 (restore 00000800, was 00000800)
<7>restore f6400048 (restore 0000ffff, was 0000ffff)
<7>restore f6400050 (restore 0000a82a, was 0000aaaa)
<7>restore f6400054 (restore 00000097, was 00000096)
<7>restore f6400058 (restore 000000ff, was 000000ff)
<7>restore f6400060 (restore 01aaaaa2, was 01aaaaa2)
<7>restore f6400064 (restore 000033cf, was 000033cf)
<7>restore f6400068 (restore 0000ffff, was 0000ffff)
<7>restore f6400070 (restore 0014aaaa, was 00155555)
<7>restore f6400074 (restore 000003bf, was 000003d6)
<7>restore f6400078 (restore 000006ff, was 000007ff)
<7>restore f6400084 (restore 00000000, was 00000000)
<7>post sleep: IRQs 0x02000001, 0x00000000
<7>IRQ 16 asserted at resume
<7>post sleep, preparing to return
<7>S3C2410 PM Resume (post-restore)
<7>restore f64000c4 (restore 00000000, was 00000000)
<7>restore f64000c8 (restore 00000000, was 00000000)
<7>restore f64000d4 (restore 00000000, was 00000000)
<7>restore f64000d0 (restore 01555555, was 01555555)
<7>restore f64000d8 (restore 00001fff, was 00001fff)
<7>restore f0000008 (restore 2de23d00, was ffffff7f)
<7>restore f000001c (restore 000000be, was 00001fff)
<4>timer tcon=00000000, tcnt d8d0, tcfg 00000200,00000000, usec 00001710
<7>selected clock c03076b0 (fclk) quot 2601, calc 9599
<6>s3c2410-wdt: watchdog disabled
<6>s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
<6>s3c2440-nand s3c2440-nand: Tacls=4, 30ns Twrph0=7 52ns, Twrph1=2 15ns
<6>asic3_mmc: starting resume
<6>asic3_mmc: finished resume
<7>udc: pullup(1)
<4>acx: resume handler is experimental!
<4>rsm: got dev c323c000
<4>rsm: got adev c323c340
<4>rx3000_wlan_start
<4>ACX radio type 0x0d
<4>requesting firmware image 'WLANGEN.BIN'
<4>Restarting tasks ... <6>usb0: full speed config #1: 500 mA, Ethernet Gadget, using CDC Ethernet
<4>acx_write_fw (main):0
<4>acx_validate_fw (main):0
<4>done.
<4>requesting firmware image 'RADIO0d.BIN'
<4>acx_write_fw (radio): 0
<4>acx_validate_fw (radio): 0
<4>acx100_s_init_wep: writing WEP options
<4>initializing max packet templates
<4>NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536
<4>CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
<4>AntennaID:01 Len:02 Data:1E 00
<4>PowerLevelID:0A Len:00 Data:
<4>DataRatesID:02 Len:05 Data:02 04 11 22 44
<4>DomainID:03 Len:07 Data:30 20 30 31 32 40 41
<4>ProductID:04 Len:09 Data:TI ACX100
<4>ManufacturerID:05 Len:07 Data:TI Tes
<4>acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form factor 0x03 (Compact Flash), EEPROM version 0x05: uploaded firmware 'Rev 1.10.7.0' ===
<4>rsm: bringing up interface
<4>acx_set_status(1):SCANNING
<4>updating initial settings on iface activation
<4>get_mask 0x00000000, set_mask 0x003FFFFF
<4>important setting has been changed. Need to update packet templates, too
<4>updating packet templates
<4>rates_basic:0003->03, rates_supported:0127->1F
<4>BSS_Type = 0
<4>JoinBSSID MAC:7E:CB:56:BE:41:24
<4>updating Tx fallback to 1 retries
<4>updating transmit power: 14 dBm
<4>wlan0: changing radio power level to 14 dBm (47)
<4>updating sensitivity value: 176
<4>updating antenna value: 0x8D
<4>updating Energy Detect (ED) threshold: 112
<4>updating Channel Clear Assessment (CCA) value: 0x0D
<4>updating power LED status: 1
<4>updating channel to: 7
<4>updating: enable Tx
<4>updating: enable Rx on channel: 7
<4>sta_list_add: sta=00:14:A5:AF:0D:40
<4>updating short retry limit: 7, long retry limit: 4
<4>updating tx MSDU lifetime: 4096
<4>updating regulatory domain: 0x30
<4>setting RXconfig to 2010:0FDD
<4>updating WEP key settings
<4>setting WEP key 0 as default
<4>setting WEP Options
<4>acx_set_status(1):SCANNING
<4>starting radio scan
<4>get_mask 0x00000000, set_mask 0x00000000 - after update
<4>rsm: acx up done
<4>rsm: device attached
<4>sta_list_add: sta=00:14:BF:DC:09:58
<4>acx_i_timer: adev->status=1 (SCANNING)
<4>continuing scan (1 sec)
<4>acx: unknown EID 221 in mgmt frame at offset 57. IE: DD 09 00 10 18 02 00 10 00 00 00
<4>sta_list_add: sta=00:14:A5:AF:0D:40
<4>acx: unknown EID 221 in mgmt frame at offset 57. IE: DD 09 00 10 18 02 00 10 00 00 00
<4>acx: unknown EID 221 in mgmt frame at offset 57. IE: DD 09 00 10 18 02 00 10 00 00 00
<4>sta_list_add: sta=00:90:4B:84:D3:48
<4>acx_i_timer: adev->status=1 (SCANNING)
<4>continuing scan (2 sec)
<4>scan table: SSID="SES Inactive" CH=4 SIR=36 SNR=1
<4>peer_cap 0x0411, needed_cap 0x0002
<4>scan table: SSID="rx3000" CH=7 SIR=52 SNR=0
<4>peer_cap 0x0002, needed_cap 0x0002
<4>found station with matching ESSID! ('rx3000' station, 'rx3000' config)
<4>matching station found: 7E:CB:56:BE:41:24, joining
<4>acx_set_status(4):ASSOCIATED
<4>get_mask 0x00000000, set_mask 0x00000004
<4>updating packet templates
<4>rates_basic:0003->03, rates_supported:0127->1F
<4>BSS_Type = 0
<4>JoinBSSID MAC:7E:CB:56:BE:41:24
<4>get_mask 0x00000000, set_mask 0x00000000 - after update
<4>rates_basic:0003->03, rates_supported:0127->1F
<4>BSS_Type = 0
<4>JoinBSSID MAC:7E:CB:56:BE:41:24
<4>acx_i_timer: adev->status=4 (ASSOCIATED)
<4>sta_list_add: sta=00:13:02:A7:FA:3B
<6>NETDEV WATCHDOG: wlan0: transmit timed out
<4>wlan0: FAILED to free any of the many full tx buffers. Switching to emergency freeing. Please report!
<4>wlan0: tx timeout!
<4>wlan0: less than 5 minutes since last radio recalibration