rendered paste bodyRaw file loaded 0x00218000-0x0040235f, assumed entry at 0x00218000
RedBoot> exec
Using base address 0x00218000 and length 0x001ea360
Uncompressing Linux................................................................................................................................. done, booting the kernel.
^CLinux version 2.6.21-rt9-ep93xx-m9 (gruberm@grma-linux) (gcc version 4.1.2) #1 PREEMPT RT Tue May 29 19:09:05 CEST 2007
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: Contec Hypercontrol Micro9-H
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
Built 1 zonelists. Total pages: 16192
Kernel command line: console=ttyAM1 slram=nvram,0x30000000,0x30100000 root=/dev/nfs nfsroot=192.168.1.223:/export ip=192.168.1.217:192.168.1.223:192.168.1.254:255.255.255.0::eth0:
WARNING: experimental RCU implementation.
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
num_possible_cpus(): 1
CPU#0: allocated 2097152 bytes trace buffer.
CPU#0: allocated 2097152 bytes max-trace buffer.
allocated 2097152 bytes out-trace buffer.
tracer: a total of 6291456 bytes allocated.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB 32MB = 64MB total
Memory: 54136KB available (3392K code, 794K data, 388K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] __init_begin+0x3fff8000/0x30
hardirqs last disabled at (0): [<c008510c>] copy_process+0x344/0x1228
softirqs last enabled at (0): [<c008510c>] copy_process+0x344/0x1228
softirqs last disabled at (0): [<00000000>] __init_begin+0x3fff8000/0x30
BUG: at kernel/sched.c:4303 __schedule()
[<c006e728>] (dump_stack+0x0/0x28) from [<c0308e44>] (__schedule+0xa24/0xac8)
[<c0308420>] (__schedule+0x0/0xac8) from [<c03090fc>] (schedule+0xdc/0x128)
[<c0309020>] (schedule+0x0/0x128) from [<c009d7f4>] (kthread+0xcc/0x12c)
r4 = C04D4000
[<c009d728>] (kthread+0x0/0x12c) from [<c008a4f4>] (do_exit+0x0/0x814)
r7 = 00000000 r6 = 00000000 r5 = 00000000 r4 = 00000000
---------------------------
| preempt count: 00000000 ]
| 0-level deep critical section nesting:
----------------------------------------
NET: Registered protocol family 16
ep93xx: PLL1 running at 400 MHz, PLL2 at 192 MHz
ep93xx: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 5, 155648 bytes)
TCP bind hash table entries: 2048 (order: 5, 139264 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
ep93xx Backlight Driver Initialized.
Console: switching to colour frame buffer device 80x30
fb0: Cirrus EP93xx frame buffer device
ep93xxfb: framebuffer at 0x5d00000, mapped to 0xffc00000, size 604k
ep93xxfb: mode is 640x480x16, linelength=1280
Micro9 Watchdog: Version 0.01
oki_ml9260: remap /dev/can0 memory physical 0x20000000 to virtual 0xc6850000.
oki_ml9260: /dev/can0 IRQ-handler installed.
oki_ml9260: remap /dev/can1 memory physical 0x21000000 to virtual 0xc6852000.
oki_ml9260: /dev/can1 IRQ-handler installed.
oki_ml9260: Version: 0.04 registered successfully.
Contec Steuerungstechnik und Automation Ges.m.b.H
Waldeck 1 / 6330 Kufstein / Austria
Serial: AMBA driver $Revision: 1.41 $
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
ep93xx-pwm ep93xx-pwm: : PWM initalized
ep93xx-eth version 0.1 loading
eth0: ep93xx on-chip ethernet, IRQ 39, 00:50:c2:40:a0:05.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
pata_ep93xx pata_ep93xx.0: version 0.3
ata1: PATA max PIO4 cmd 0x00000002 ctl 0x00000019 bmdma 0x00000000 irq 0
ata: polling mode
scsi0 : pata_ep93xx
ata1: disabling port
physmap platform flash device: 04000000 at 10000000
physmap-flash.0: Found 2 x16 devices at 0x0 in 32-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash.0 at offset 0x1fe0000
6 RedBoot partitions found on MTD device physmap-flash.0
Creating 6 MTD partitions on "physmap-flash.0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00240000 : "kernel"
0x00240000-0x00c00000 : "rootfs"
0x00c00000-0x01fe0000 : "savefs"
0x01fe0000-0x01fff000 : "FIS directory"
mtd: partition "FIS directory" doesn't end on an erase block -- force read-only
0x01fff000-0x02000000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't start on an erase block boundary -- force read-only
ep93xx-spi ep93xx-spi.1: : SPI Controller initalized
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usb 1-3: new low speed USB device using ep93xx-ohci and address 2
usb 1-3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: NOVATEK USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-ep93xx-3
input: NOVATEK USB Keyboard as /class/input/input1
input: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-ep93xx-3
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
mice: PS/2 mouse device common for all mice
input: ep93xx-8x8-keyboard as /class/input/input2
ep93xx: ep93xx-8x8-keyboard init done
input: LS7366R left/right keyboard as /class/input/input3
input: Cirrus EP93xx touchscreen as /class/input/input4
i2c /dev entries driver
ds1307 0-0068: rtc core: registered ds1307 as rtc0
Micro9 24C32 I2C eeprom: detected
Micro9 24C32 I2C eeprom: eth0 MAC address 0x00:0x50:0xc2:0x40:0xa0:0x05
Registered led device: ep93xx:green
Registered led device: ep93xx:red
Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC).
ep93xx-ac97: resetting ac97 controller
ep93xx-ac97: resetting bus.. done (10)
ep93xx-ac97: waiting for codec ready.. ready (43)
ep93xx-ac97: waiting for codec to settle.. settled (0)
ALSA device list:
#0: ep93xx-ac97 (Cirrus Logic CS4202 rev 3)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
ep93xx-io ep93xx-io: IO init
ep93xx-io ep93xx-io: KEYMATRIX found, hole Port C and D not possible
ep93xx-io ep93xx-io: PATA driver found, hole Port E,G and H not possible
ep93xx-io ep93xx-io: IO initalized
ds1307 0-0068: setting the system clock to 2000-01-01 00:04:41 (946685081)
IP-Config: Complete:
device=eth0, addr=192.168.1.217, mask=255.255.255.0, gw=192.168.1.254,
host=192.168.1.217, domain=, nis-domain=(none),
bootserver=192.168.1.223, rootserver=192.168.1.223, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.223
Looking up port of RPC 100005/1 on 192.168.1.223
VFS: Mounted root (nfs filesystem).
*****************************************************************************
* *
* REMINDER, the following debugging options are turned on in your .config: *
* *
* CONFIG_DEBUG_RT_MUTEXES *
* CONFIG_CRITICAL_PREEMPT_TIMING *
* CONFIG_CRITICAL_IRQSOFF_TIMING *
* CONFIG_FUNCTION_TRACE *
* CONFIG_DEBUG_SLAB *
* *
* they may increase runtime overhead and latencies. *
* *
*******************************************************************