rendered paste bodylocalhost willie # dmesg
000000a0000 (reserved)
BIOS-e820: 00000000000ea800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
BIOS-e820: 000000000f7f0000 - 000000000f7ffc00 (ACPI data)
BIOS-e820: 000000000f7ffc00 - 000000000f800000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
Entering add_active_range(0, 0, 63472) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 63472
HighMem 63472 -> 63472
early_node_map[1] active PFN ranges
0: 0 -> 63472
On node 0 totalpages: 63472
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 463 pages used for memmap
Normal zone: 58913 pages, LIFO batch:15
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7080
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0f7fb7ed
ACPI: FADT (v001 FIC A440 0x06040000 PTL_ 0x000f4240) @ 0x0f7ffb64
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0f7ffbd8
ACPI: DSDT (v001 FIC A440 0x06040000 MSFT 0x0100000c) @ 0x00000000
Allocating PCI resources starting at 10000000 (gap: 0f800000:f0780000)
Detected 846.877 MHz processor.
Built 1 zonelists. Total pages: 62977
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 video=tridentfb:ywrap,1024x768-16@60 splash=silent,theme:livecd-2007.0 CONSOLE=/dev/tty1 quiet udev
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011f2000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Speakup v-2.00 CVS: Sat Oct 7 10:52:29 EDT 2006 : initialized
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 242400k/253888k available (2265k kernel code, 10844k reserved, 555k data, 204k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffea000 - 0xfffff000 ( 84 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0000000 - 0xff7fe000 ( 759 MB)
lowmem : 0xc0000000 - 0xcf7f0000 ( 247 MB)
.init : 0xc03c4000 - 0xc03f7000 ( 204 kB)
.data : 0xc0336461 - 0xc03c11d4 ( 555 kB)
.text : 0xc0100000 - 0xc0336461 (2265 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1695.06 BogoMIPS (lpj=8475315)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel Pentium III (Coppermine) stepping 06
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0020)
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd83e, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 8000-80ff claimed by vt82c586 ACPI
PCI quirk: region 8100-810f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
ACPI: PCI Interrupt Link [LNKC] (IRQs *5)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: Power Resource [PFAN] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:06: ioport range 0x8000-0x807f could not be reserved
pnp: 00:06: ioport range 0x8100-0x810f has been reserved
pnp: 00:06: ioport range 0xfe00-0xfe01 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fb100000-fc7fffff
PREFETCH window: 20000000-200fffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 10000000-13ffffff
MEM window: 14000000-17ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0a.1
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 18000000-1bffffff
MEM window: 1c000000-1fffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:0a.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5409k freed
Simple Boot Flag at 0x39 set to 0x1
squashfs: version 3.2 (2007/01/02) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler deadline registered (default)
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
cyblafb: CyblaFB version 0.62 initializing
tridentfb: Trident framebuffer 0.7.8-NEWAPI initializing
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
tridentfb: framebuffer size = 8192 Kb
tridentfb: 0000:01:00.0 board found
tridentfb: 1024x768 flat panel found
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'livecd-2007.0'
fbsplash: switched splash state to 'on' on console 0
tridentfb: fb0: Trident frame buffer device 1024x768-16bpp
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0x1420-0x1427, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1428-0x142f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HTS541040G9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78140160 sectors (40007 MB) w/7539KiB Cache, CHS=16383/255/63<6>hda: hw_config=600b
, UDMA(66)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 204k freed
Time: tsc clocksource has been installed.
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 5, io base 0x00001400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
libata version 2.00 loaded.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
JFS: nTxBlock = 1939, nTxLock = 15517
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x0
parport_pc: VIA parallel port disabled in BIOS
Yenta: CardBus bridge found at 0000:00:0a.0 [1509:4460]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x012c1722, devctl 0x64
Yenta: ISA IRQ mask 0x08d8, PCI irq 10
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:0a.1 [1509:4460]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.1, mfunc 0x012c1722, devctl 0x64
Linux agpgart interface v0.101 (c) Dave Jones
Yenta: ISA IRQ mask 0x08d8, PCI irq 10
Socket status: 30000059
agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
agpgart: AGP aperture is 16M @ 0xfd000000
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
bcm43xx driver
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
pccard: PCMCIA card inserted into slot 1
via686a 0000:00:07.4: base address not set - upgrade BIOS or use force_addr=0xaddr
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:07.5 to 64
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia1.0
ASIC rev 1,<6>eth1: Megahertz 574B at io 0x300, irq 3, hw_addr 00:50:DA:D3:1F:8B.
64K FIFO split 1:1 Rx:Tx, autoselect MII interface.
EXT3 FS on hda3, internal journal
Adding 530136k swap on /dev/hda2. Priority:-1 extents:1 across:530136k
Real Time Clock Driver v1.12ac
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
SoftMAC: Associate: Scanning for networks first.
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Canceling existing associate request!
SoftMAC: Queueing Authentication Request to 00:11:d8:da:67:d8
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:11:d8:da:67:d8.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Already requested authentication, waiting...
SoftMAC: Already requested authentication, waiting...
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 5/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
eth1: found link beat
eth1: autonegotiation complete: 100baseT-FD selected
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Queueing Authentication Request to 00:11:d8:da:67:d8
SoftMAC: Sent Authentication Request to 00:11:d8:da:67:d8.
SoftMAC: Open Authentication completed with 00:11:d8:da:67:d8
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Already associating or associated to 00:11:d8:da:67:d8
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: sent association request!
SoftMAC: associating failed (reason: 0x19)!
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Queueing Authentication Request to 00:11:d8:da:67:d8
SoftMAC: Cannot associate without being authenticated, requested authentication
SoftMAC: Sent Authentication Request to 00:11:d8:da:67:d8.
SoftMAC: Open Authentication completed with 00:11:d8:da:67:d8
SoftMAC: sent association request!
SoftMAC: associating failed (reason: 0x19)!
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
localhost willie #