rendered paste bodyLinux version 2.6.18-chw-13 (root@mythtv) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP PREEMPT Tue Mar 6 19:57:00 PST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
On node 0 totalpages: 122864
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 118768 pages, LIFO batch:31
DMI 2.2 present.
ACPI: RSDP (v000 VT9174 ) @ 0x000f6650
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 20000000 (gap: 1e000000:e1ff0000)
Detected 999.872 MHz processor.
Built 1 zonelists. Total pages: 122864
Kernel command line: auto BOOT_IMAGE=knoppix ro root=343 apm=power-off nomce quiet resume2=swap:/dev/hdb2 noresume2
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013cb000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 480244k/491456k available (4292k kernel code, 10704k reserved, 1348k data, 268k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2000.79 BogoMIPS (lpj=1000396)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0380b03d 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0380b13d 00000000 00000000 00000000 00000000 0000003d 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 1e20)
CPU0: Centaur VIA Nehemiah stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 111k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb260, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by vt8235 PM
PCI quirk: region 0500-050f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
VIA RNG detected
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0x400-0x47f could not be reserved
pnp: 00:02: ioport range 0x500-0x50f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e6000000-e7ffffff
PREFETCH window: e0000000-e3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1179968570.657:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFS: nTxBlock = 3753, nTxLock = 30031
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
vesafb: framebuffer at 0xe0000000, mapped to 0xdea80000, using 3750k, total 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=31
vesafb: protected mode interface info at c000:7dc7
vesafb: pmi: set display start = c00c7e18, set palette = c00c7e71
vesafb: pmi: ports = 3b4 3b5 3d4 3d5 3cc 3d7 3d8 3d9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 45842 bytes,<6>...found (800x600, 21500 bytes, v3).
Console: switching to colour frame buffer device 75x24
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4
Copyright (c) 1999-2006 Intel Corporation.
pcnet32.c:v1.32 18.Mar.2006 tsbogend@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xe8002000, 00:40:63:d5:2f:d3, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 0081.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hdb: MAXTOR 6L040J2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: SAMSUNG CDRW/DVD SM-352N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdb: max request size: 128KiB
hdb: 78177792 sectors (40027 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3
hdd: ATAPI 16X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v1.1-646.<7>libata version 2.00 loaded.
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 148 MB/s
raid6: int32x2 132 MB/s
raid6: int32x4 125 MB/s
raid6: int32x8 113 MB/s
raid6: mmxx1 328 MB/s
raid6: mmxx2 488 MB/s
raid6: sse1x1 292 MB/s
raid6: sse1x2 437 MB/s
raid6: using algorithm sse1x2 (437 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 2212.000 MB/sec
raid5: using function: pIII_sse (2212.000 MB/sec)
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
Suspend2 Core.
Suspend2 Userspace UI Support module loaded.
Suspend2 Userspace Storage Manager module loaded.
Suspend2 Compressor module loaded.
Time: tsc clocksource has been installed.
Suspend2 Encryptor module loaded.
Suspend2 Block I/O module loaded.
Suspend2 Swap Allocator module loaded.
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
input: AT Translated Set 2 keyboard as /class/input/input0
VFS: Mounted root (ext2 filesystem).
Suspend2 2.2.8.4: SwapAllocator: Signature found.
Suspend2 2.2.8.4: Resuming enabled.
Suspend2 2.2.8.4: Normal swapspace found.
Suspend2 2.2.8.4: No image found.
Suspend2 2.2.8.4: Resuming disabled as requested.
(fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recovered transactions 1374 to 2376
(fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 10759 and revoked 182/239 blocks
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 268k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 12, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000dc00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 5, io mem 0xe8001000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 4-3: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 4-3: configuration #1 chosen from 1 choice
NET: Registered protocol family 23
hub 4-0:1.0: over-current change on port 5
Linux agpgart interface v0.101 (c) Dave Jones
usb 2-1: USB disconnect, address 2
usb 2-2: USB disconnect, address 3
ieee1394: Initialized config rom entry `ip1394'
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 32M @ 0xe4000000
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
usb 2-2: new low speed USB device using uhci_hcd and address 4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[12] MMIO=[e8000000-e80007ff] Max Packet=[2048] IR/IT contexts=[4/8]
usb 2-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[004063500000fd3d]
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ts: Compaq touchscreen protocol output
Adding 996020k swap on /dev/hdb2. Priority:-1 extents:1 across:996020k
EXT3 FS on hdb3, internal journal
Linux video capture interface: v2.00
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: AUDIO driver version 0.0.0 loaded
Non-volatile memory driver v1.2
saa7130/34: v4l2 driver version 0.2.14 loaded
Vendor: AFT Model: CF PRO-9XP Rev: 9144
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:0: Attached scsi removable disk sda
Vendor: AFT Model: SM PRO-9XP Rev: 9144
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:1: Attached scsi removable disk sdb
Vendor: AFT Model: SD PRO-9XP Rev: 9144
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:2: Attached scsi removable disk sdc
Vendor: AFT Model: MS PRO-9XP Rev: 9144
Type: Direct-Access ANSI SCSI revision: 00
sd 0:0:0:3: Attached scsi removable disk sdd
usb-storage: device scan complete
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
Registering unionfs 20061031-1310
unionfs: debugging is not enabled
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
Time: acpi_pm clocksource has been installed.
fuse init (API version 7.7)
NET: Registered protocol family 17
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized via 2.7.4 20051116 on minor 0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link up, 100Mbps, half-duplex, lpa 0x0081
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 21500 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 21500 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 21500 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 21500 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 21500 bytes, v3).
bootsplash: status on console 5 changed to on
lirc_dev: IR Remote Control driver registered, at major 61
usbcore: registered new driver lirc_streamzap
lirc_streamzap $Revision: 1.17 $ registered
eth0: no IPv6 routers present
UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'JABBERWOCKY', timestamp 2001/08/22 02:31 (1f10)
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000010
printing eip:
df38d863
*pde = 00000000
Oops: 0000 [#1]
PREEMPT SMP
Modules linked in: udf autofs4 lirc_streamzap lirc_dev ipv6 via drm af_packet fuse pcmcia yenta_socket rsrc_nonstatic pcmcia_core video thermal sbs processor i2c_ec fan container button battery ac unionfs sbp2 ohci_hcd cx88_vp3054_i2c cx8802 cx88xx saa7134_dvb dvb_pll saa7134 ir_kbd_i2c video_buf_dvb tda1004x nvram dvb_bt8xx dvb_core bt878 bttv video_buf ir_common compat_ioctl32 i2c_algo_bit btcx_risc tveeprom videodev v4l2_common v4l1_compat firmware_class tsdev eth1394 usbhid parport_pc parport 8250_pnp 8250 serial_core shpchp pci_hotplug usb_storage snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event snd_seq i2c_viapro i2c_core ohci1394 ieee1394 via_agp agpgart via_ircc irda snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc snd_mpu401_uart snd_rawmidi snd_seq_device ehci_hcd snd soundcore serio_raw uhci_hcd usbcore evdev
CPU: 0
EIP: 0060:[<df38d863>] Not tainted VLI
EFLAGS: 00010286 (2.6.18-chw-13 #1)
EIP is at via_driver_vblank_wait+0x33/0x150 [via]
eax: 00000000 ebx: d8890000 ecx: 00000000 edx: df38d830
esi: ae6260c0 edi: d8da0800 ebp: c8b5bf0c esp: c8b5bec4
ds: 007b es: 007b ss: 0068
Process mythfrontend (pid: 3562, ti=c8b5a000 task=ddf510f0 task.ti=c8b5a000)
Stack: d9672880 c8d20800 00000001 00000000 d8dc24a0 d9672880 00000000 ae6260c0
d8da0800 0000000b df3a7516 d8da0800 c8b5bf0c ddde86a4 c01846c0 c0179cb5
c8d2084c 00000000 00000001 b743c34c b7f6a000 c8b5bf30 00000017 d9672880
Call Trace:
[<df3a7516>] drm_wait_vblank+0x166/0x210 [drm]
[<c01846c0>] chrdev_open+0x0/0x1b0
[<c0179cb5>] __dentry_open+0x1c5/0x250
[<df3a73b0>] drm_wait_vblank+0x0/0x210 [drm]
[<df3a5ecc>] drm_ioctl+0x9c/0x1e0 [drm]
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c018e08a>] do_ioctl+0x5a/0x70
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c018e0f2>] vfs_ioctl+0x52/0x2e0
[<c018a989>] putname+0x29/0x40
[<c018e3dd>] sys_ioctl+0x5d/0x70
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c01031f7>] syscall_call+0x7/0xb
[<c010643a>] arch_ptrace+0x29a/0x7b0
Code: 84 16 3b df 8b 7c 24 2c 8b 6c 24 30 85 c0 8b 9f 3c 03 00 00 0f 85 e8 00 00 00 85 db 0f 84 fd 00 00 00 8b 43 0c 8b 8b c4 fc 00 00 <8b> 50 10 8b 82 00 02 00 00 09 c8 89 82 00 02 00 00 89 e0 25 00
EIP: [<df38d863>] via_driver_vblank_wait+0x33/0x150 [via] SS:ESP 0068:c8b5bec4
<5>SCSI device sdc: 494080 512-byte hdwr sectors (253 MB)
sdc: Write Protect is off
sdc: Mode Sense: 02 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 494080 512-byte hdwr sectors (253 MB)
sdc: Write Protect is off
sdc: Mode Sense: 02 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
smbfs: Unrecognized mount option noexec
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000010
printing eip:
df38d863
*pde = 00000000
Oops: 0000 [#2]
PREEMPT SMP
Modules linked in: smbfs udf autofs4 lirc_streamzap lirc_dev ipv6 via drm af_packet fuse pcmcia yenta_socket rsrc_nonstatic pcmcia_core video thermal sbs processor i2c_ec fan container button battery ac unionfs sbp2 ohci_hcd cx88_vp3054_i2c cx8802 cx88xx saa7134_dvb dvb_pll saa7134 ir_kbd_i2c video_buf_dvb tda1004x nvram dvb_bt8xx dvb_core bt878 bttv video_buf ir_common compat_ioctl32 i2c_algo_bit btcx_risc tveeprom videodev v4l2_common v4l1_compat firmware_class tsdev eth1394 usbhid parport_pc parport 8250_pnp 8250 serial_core shpchp pci_hotplug usb_storage snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event snd_seq i2c_viapro i2c_core ohci1394 ieee1394 via_agp agpgart via_ircc irda snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc snd_mpu401_uart snd_rawmidi snd_seq_device ehci_hcd snd soundcore serio_raw uhci_hcd usbcore evdev
CPU: 0
EIP: 0060:[<df38d863>] Not tainted VLI
EFLAGS: 00210286 (2.6.18-chw-13 #1)
EIP is at via_driver_vblank_wait+0x33/0x150 [via]
eax: 00000000 ebx: d8890000 ecx: 00000000 edx: df38d830
esi: a95ff0c0 edi: d8da0800 ebp: d4fb9f0c esp: d4fb9ec4
ds: 007b es: 007b ss: 0068
Process mythfrontend (pid: 4108, ti=d4fb8000 task=d9954290 task.ti=d4fb8000)
Stack: d9672880 dd683a80 00000001 00000000 00200002 00200002 00000000 a95ff0c0
d8da0800 0000000b df3a7516 d8da0800 d4fb9f0c 00166c00 00000000 00000016
00000001 00000000 00000001 b744d34c b7f7b000 c13c5620 00000000 d9672880
Call Trace:
[<df3a7516>] drm_wait_vblank+0x166/0x210 [drm]
[<df3a73b0>] drm_wait_vblank+0x0/0x210 [drm]
[<df3a5ecc>] drm_ioctl+0x9c/0x1e0 [drm]
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c018e08a>] do_ioctl+0x5a/0x70
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c018e0f2>] vfs_ioctl+0x52/0x2e0
[<c0128af4>] __do_softirq+0x74/0xf0
[<c018e3dd>] sys_ioctl+0x5d/0x70
[<c010643a>] arch_ptrace+0x29a/0x7b0
[<c01031f7>] syscall_call+0x7/0xb
[<c010643a>] arch_ptrace+0x29a/0x7b0
Code: 84 16 3b df 8b 7c 24 2c 8b 6c 24 30 85 c0 8b 9f 3c 03 00 00 0f 85 e8 00 00 00 85 db 0f 84 fd 00 00 00 8b 43 0c 8b 8b c4 fc 00 00 <8b> 50 10 8b 82 00 02 00 00 09 c8 89 82 00 02 00 00 89 e0 25 00
EIP: [<df38d863>] via_driver_vblank_wait+0x33/0x150 [via] SS:ESP 0068:d4fb9ec4
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449
hdd: command error: status=0x51 { DriveReady SeekComplete Error }
hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdd:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 01 c0 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdd, sector 1792
Buffer I/O error on device hdd, logical block 448
Buffer I/O error on device hdd, logical block 449