rendered paste bodyscsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320ALP PCIx Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
scsi 1:0:0:0: Direct-Access SB-3160S LINUX.CC R001 PQ: 0 ANSI: 3
target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
target1:0:0: Beginning Domain Validation
target1:0:0: wide asynchronous
target1:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target1:0:0: Ending Domain Validation
hda: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:8:0: Attached scsi generic sg1 type 3
scsi 0:1:0:0: Attached scsi generic sg2 type 0
scsi 0:1:1:0: Attached scsi generic sg3 type 0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input2
piix4_smbus 0000:00:02.0: Found 0000:00:02.0 device
Adding 7815612k swap on /dev/sda2. Priority:-1 extents:1 across:7815612k
EXT3 FS on sda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PM: Writing back config space on device 0000:04:04.0 at offset b (was 166814e4,
writing 3291014)
PM: Writing back config space on device 0000:04:04.0 at offset 3 (was 804000, wr
iting 804010)
PM: Writing back config space on device 0000:04:04.0 at offset 2 (was 2000000, w
riting 2000003)
PM: Writing back config space on device 0000:04:04.0 at offset 1 (was 2b00000, w
riting 2b00146)
sdb : very big device. try to use READ CAPACITY(16).
sdb : READ CAPACITY(16) failed.
sdb : status=0, message=00, host=5, driver=00
sdb : use 0xffffffff as device size
SCSI device sdb: 4294967296 512-byte hdwr sectors (2199023 MB)
sdb: Write Protect is off
sdb: Mode Sense: cb 00 00 08
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb : very big device. try to use READ CAPACITY(16).
sdb : READ CAPACITY(16) failed.
sdb : status=0, message=00, host=5, driver=00
sdb : use 0xffffffff as device size
SCSI device sdb: 4294967296 512-byte hdwr sectors (2199023 MB)
sdb: Write Protect is off
sdb: Mode Sense: cb 00 00 08
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg4 type 0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]