rendered paste bodyLinux version 2.6.13.3 (root@Orbital) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #8 SMP Tue Apr 11 20:46:19 GMT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: AMI Product ID: CNB30LE APIC at: 0xFEE00000
Processor #0 6:8 APIC version 17
Processor #1 6:8 APIC version 17
I/O APIC #4 Version 17 at 0xFEC00000.
I/O APIC #5 Version 17 at 0xFEC01000.
Enabling APIC mode: Flat. Using 2 I/O APICs
Processors: 2
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda3
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec01000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 866.923 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905792k/917504k available (1948k kernel code, 11200k reserved, 808k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1736.13 BogoMIPS (lpj=3472275)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 06
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1733.55 BogoMIPS (lpj=3467119)
CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (3469.69 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdbb1, last bus=1
PCI: Using configuration type 1
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:07.0
PCI: Discovered peer bus 01
PCI: Using IRQ router default [1166/0009] at 0000:00:00.0
PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 169
PCI->APIC IRQ transform: 0000:00:03.0[A] -> IRQ 145
PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 153
PCI->APIC IRQ transform: 0000:00:06.0[A] -> IRQ 161
PCI->APIC IRQ transform: 0000:00:0f.2[A] -> IRQ 10
PCI->APIC IRQ transform: 0000:01:04.0[A] -> IRQ 177
PCI->APIC IRQ transform: 0000:01:05.0[A] -> IRQ 185
PCI->APIC IRQ transform: 0000:01:05.1[B] -> IRQ 193
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Intel(R) PRO/1000 Network Driver - version 6.0.60-k2
Copyright (c) 1999-2005 Intel Corporation.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Intel(R) PRO/10GbE Network Driver - version 1.0.95-k2
Copyright (c) 1999-2005 Intel Corporation.
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth1: OEM i82557/i82558 10/100 Ethernet, 00:E0:18:0B:B3:3F, IRQ 169.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 668081-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20268: IDE controller at PCI slot 0000:00:03.0
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xfe9f4000
PDC20268: 100% native mode on irq 145
ide2: BM-DMA at 0xcf90-0xcf97, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xcf98-0xcf9f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
hde: Maxtor 6Y250P0, ATA DISK drive
hdf: Maxtor 6Y250P0, ATA DISK drive
ide2 at 0xcff0-0xcff7,0xcfe6 on irq 145
Probing IDE interface ide3...
hdg: WDC WD2500JB-00GVA0, ATA DISK drive
hdh: WDC WD2500JB-00GVA0, ATA DISK drive
ide3 at 0xcfa8-0xcfaf,0xcfe2 on irq 145
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST320014A, ATA DISK drive
hdb: CD-ROM 40X/AKU, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: WDC WD2500JB-00FUA0, ATA DISK drive
hdd: WDC WD3000JB-00KFA0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hde: max request size: 1024KiB
hde: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63, UDMA(100)
hde: cache flushes supported
hde: hde1
hdf: max request size: 1024KiB
hdf: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63, UDMA(100)
hdf: cache flushes supported
hdf: hdf1
hdg: max request size: 1024KiB
hdg: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hdg: cache flushes supported
hdg: hdg1
hdh: max request size: 1024KiB
hdh: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hdh: cache flushes supported
hdh: hdh1
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, (U)DMA
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: max request size: 1024KiB
hdc: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, (U)DMA
hdc: cache flushes supported
hdc: hdc1
hdd: max request size: 1024KiB
hdd: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, (U)DMA
hdd: cache flushes supported
hdd: hdd1
hdb: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
libata version 1.12 loaded.
sata_sil version 0.9
ata1: SATA max UDMA/100 cmd 0xF8824080 ctl 0xF882408A bmdma 0xF8824000 irq 153
ata2: SATA max UDMA/100 cmd 0xF88240C0 ctl 0xF88240CA bmdma 0xF8824008 irq 153
ata3: SATA max UDMA/100 cmd 0xF8824280 ctl 0xF882428A bmdma 0xF8824200 irq 153
ata4: SATA max UDMA/100 cmd 0xF88242C0 ctl 0xF88242CA bmdma 0xF8824208 irq 153
ata1: dev 0 cfg 49:2f00 82:7869 83:7d09 84:4003 85:7869 86:3c01 87:4003 88:203f
ata1: dev 0 ATA, max UDMA/100, 488397168 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:007f
ata2: dev 0 ATA, max UDMA/133, 490234752 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
ata3: dev 0 cfg 49:2f00 82:7c69 83:7f09 84:4003 85:7c69 86:3e01 87:4003 88:207f
ata3: dev 0 ATA, max UDMA/133, 490234752 sectors: lba48
ata3: dev 0 configured for UDMA/100
scsi2 : sata_sil
ata4: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata4: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
ata4: dev 0 configured for UDMA/100
scsi3 : sata_sil
Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6L250S0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD3200JD-00K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
ata5: SATA max UDMA/100 cmd 0xF8826080 ctl 0xF882608A bmdma 0xF8826000 irq 177
ata6: SATA max UDMA/100 cmd 0xF88260C0 ctl 0xF88260CA bmdma 0xF8826008 irq 177
ata7: SATA max UDMA/100 cmd 0xF8826280 ctl 0xF882628A bmdma 0xF8826200 irq 177
ata8: SATA max UDMA/100 cmd 0xF88262C0 ctl 0xF88262CA bmdma 0xF8826208 irq 177
ata5: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata5: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
ata5: dev 0 configured for UDMA/100
scsi4 : sata_sil
ata6: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata6: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
ata6: dev 0 configured for UDMA/100
scsi5 : sata_sil
ata7: no device found (phy stat 00000000)
scsi6 : sata_sil
ata8: no device found (phy stat 00000000)
scsi7 : sata_sil
Vendor: ATA Model: WDC WD3200SD-01K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD3200SD-01K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdc: drive cache: write back
sdc: sdc1
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdd: drive cache: write back
sdd: sdd1
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sde: drive cache: write back
SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sde: drive cache: write back
sde: sde1
Attached scsi disk sde at scsi4, channel 0, id 0, lun 0
SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdf: drive cache: write back
SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdf: drive cache: write back
sdf: sdf1
Attached scsi disk sdf at scsi5, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
input: AT Translated Set 2 keyboard on isa0060/serio0
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdf1 ...
md: adding sdf1 ...
md: adding sde1 ...
md: created md0
md: bind<sde1>
md: bind<sdf1>
md: running: <sdf1><sde1>
md0: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdf1
raid0: comparing sdf1(312568576) with sdf1(312568576)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sde1
raid0: comparing sde1(312568576) with sdf1(312568576)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 625137152 blocks.
raid0 : conf->hash_spacing is 625137152 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k freed
Adding 488368k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
ReiserFS: hdc1: found reiserfs format "3.6" with standard journal
ReiserFS: hdc1: using ordered data mode
ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc1: checking transaction log (hdc1)
ReiserFS: hdc1: Using r5 hash to sort names
ReiserFS: hdd1: found reiserfs format "3.6" with standard journal
ReiserFS: hdd1: using ordered data mode
ReiserFS: hdd1: journal params: device hdd1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdd1: checking transaction log (hdd1)
ReiserFS: hdd1: Using r5 hash to sort names
ReiserFS: hde1: found reiserfs format "3.6" with standard journal
ReiserFS: hde1: using ordered data mode
ReiserFS: hde1: journal params: device hde1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hde1: checking transaction log (hde1)
ReiserFS: hde1: Using r5 hash to sort names
ReiserFS: hdf1: found reiserfs format "3.6" with standard journal
ReiserFS: hdf1: using ordered data mode
ReiserFS: hdf1: journal params: device hdf1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdf1: checking transaction log (hdf1)
ReiserFS: hdf1: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdg1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdh1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e1000: eth0: e1000_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex