ninex@HaMeR ~ $ sensors
it8712-isa-0d00
Adapter: ISA adapter
VCore 1: +1.12 V (min = +0.00 V, max = +4.08 V) sholud be 1.360V
VCore 2: +4.08 V (min = +0.00 V, max = +4.08 V) ALARM #i will disble this
+3.3V: +3.30 V (min = +0.00 V, max = +4.08 V) bios saing i have 3.296V
+5V: +4.95 V (min = +0.00 V, max = +6.85 V) bios saing i have 4.495V
+12V: +11.90 V (min = +0.00 V, max = +16.32 V) bios saing that i have 11.977V
-12V: +3.93 V (min = -27.36 V, max = +3.93 V) ALARM Bios not monitoring this
-5V: +4.03 V (min = -13.64 V, max = +4.03 V) ALARM Bios not monitoring this
Stdby: +6.85 V (min = +0.00 V, max = +6.85 V) ALARM Bios not monitoring this
VBat: +3.30 V ????
fan1: 5400 RPM (min = 0 RPM, div = 2) sholud be ~1674
fan2: 0 RPM (min = 0 RPM, div = 2)
fan3: 0 RPM (min = 0 RPM, div = 2)
M/B Temp: +33°C (low = -1°C, high = +127°C) sensor = thermistor Sholud be 29 C
CPU Temp: +34°C (low = -1°C, high = +127°C) sensor = thermistor is ok
Temp3: +128°C (low = -1°C, high = +127°C) sensor = disabled
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:
+33°C
Core1 Temp:
+31°C
#sensors.conf
chip "it87-*" "it8712-*"
# The values below have been tested on Asus CUSI, CUM motherboards.
# Voltage monitors as advised in the It8705 data sheet
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "Stdby"
label in8 "VBat"
# vid is not monitored by IT8705F
# comment out if you have IT8712
ignore vid
# Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
# to report the VCORE voltage approximately 0.05V higher than the board's
# BIOS does. Although it doesn't make much sense physically, uncommenting
# the next line should bring the readings in line with the BIOS' ones in
# this case.
# compute in0 -0.05+@ , @+0.05
# If 3.3V reads around 1.65V, uncomment the following line:
# compute in2 2*@ , @/2
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# A number of Gigabyte boards (GA-8IPE1000Pro, GA-8KNXP, GA-7N400-L) use
# a different resistor combination for +5V:
# compute in3 ((10/10)+1)*@ , @/((10/10)+1)
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
# For this family of chips the negative voltage equation is different from
# the lm78. The chip uses two external resistor for scaling but one is
# tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950
# data sheet is wrong)
# Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.
# Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.
# The next two are negative voltages (-12 and -5).
# The following formulas must be used. Unfortunately the datasheet
# does not give recommendations for Rin, Rf, but we can back into
# them based on a nominal +2V input to the chip, together with a 4.096V Vref.
# Formula:
# actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))
# For -12V input use Rin/Rf = 6.68
# For -5V input use Rin/Rf = 3.33
# Then you can convert the forumula to a standard form like:
compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67
compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33
#
# this much simpler version is reported to work for a
# Elite Group K7S5A board
#
# compute in5 -(36/10)*@, -@/(36/10)
# compute in6 -(56/10)*@, -@/(56/10)
#
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# set in0_min 1.5 * 0.95
# set in0_max 1.5 * 1.05
# set in1_min 2.4
# set in1_max 2.6
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in5_max -12 * 0.95
# set in5_min -12 * 1.05
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
#the chip does not support in8 min/max
# Temperature
#
# Important - if your temperature readings are completely whacky
# you probably need to change the sensor type.
# Adujst and uncomment the appropriate lines below.
# The old method (modprobe it87 temp_type=0xXX) is no longer supported.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set sensor1 3
# set sensor2 3
# set sensor3 3
# If a given sensor isn't used, you will probably want to ignore it
# (see ignore statement right below).
label temp1 "M/B Temp"
# set temp1_over 40
# set temp1_low 15
label temp2 "CPU Temp"
# set temp2_over 45
# set temp2_low 15
# ignore temp3
label temp3 "Temp3"
# set temp3_over 45
# set temp3_low 15
# The A7V8X-X has temperatures inverted, and needs a conversion for
# CPU temp. Thanks to Preben Randhol for the formula.
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893
# The A7V600 also has temperatures inverted, and needs a different
# conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# compute temp1 (@+128)/3, (3*@-128)
# Fans
# set fan1_min 0
# set fan2_min 3000
# ignore fan3
# set fan3_min 3000