#
# Configuration file for your misdn hardware
#
# Usage: /usr/sbin/misdn-init start|stop|restart|config|scan|help
#
#
# Card Settings
#
# Syntax: card=<number>,<type>[,<option>...]
#
# <number> count your cards beginning with 1
# <type> either 0x1,0x4 or 0x8 for your hfcmulti hardware,
# or the name of your card driver module.
# <option> ulaw - uLaw (instead of aLaw)
# dtmf - enable DTMF detection on all B-channels
#
# pcm_slave - set PCM bus into slave mode
# If you have a set of cards, all wired via PCM. Set
# all cards into pcm_slave mode and leave one out.
# The left card will automatically be Master.
#
# ignore_pcm_frameclock - this can be set in conjunction with
# pcm_slave. If this card has a
# PCI Bus Position before the Position
# of the Master, then this port cannot
# yet receive a frameclock, so it must
# ignore the pcm frameclock.
#
# rxclock - use clocking for pcm from ST Port
# crystalclock - use clocking for pcm from PLL (genrated on board)
# watchdog - This dual E1 Board has a Watchdog for
# transparent mode
#
#
card=1,0x4
#
# Port settings
#
# Syntax: <port_type>=<port_number>[,<port_number>...]
#
# <port_type> te_ptp - TE-Mode, PTP
# te_ptmp - TE-Mode, PTMP
# te_capi_ptp - TE-Mode (capi), PTP
# te_capi_ptmp - TE-Mode (capi), PTMP
# nt_ptp - NT-Mode, PTP
# nt_ptmp - NT-Mode, PTMP
# <port_number> port that should be considered
#
te_ptp=1,2,3,4
#
# Port Options
#
# Syntax: option=<port_number>,<option>[,<option>...]
#
# <option> master_clock - use master clock for this S/T interface
# (only once per chip, only for HFC 8/4)
# optical - optical (only HFC-E1)
# los - report LOS (only HFC-E1)
# ais - report AIS (only HFC-E1)
# slip - report SLIP (only HFC-E1)
# nocrc4 - turn off crc4 mode use double frame instead
# (only HFC-E1)
#
#option=1,master_clock
#option=2,ais,nocrc4
#option=3,optical,los,ais,slip
#
# General Options for your hfcmulti hardware
#
# poll=<number>
#
# Only one poll value must be given for all cards.
# Give the number of samples for each fifo process.
# By default 128 is used. Decrease to reduce delay, increase to
# reduce cpu load. If unsure, don't mess with it!!!
# Valid is 32, 64, 128, 256.
#
# dsp_poll=<number>
# This is the poll option which is used by mISDN_dsp, this might
# differ from the one given by poll= for the hfc based cards, since
# they can only use multiples of 32, the dsp_poll is dependant on
# the kernel timer setting which can be found in the CPU section
# in the kernel config. Defaults are there either 100Hz, 250Hz
# or 1000Hz. If your setting is either 1000 or 250 it is compatible
# with the poll option for the hfc chips, if you have 100 it is
# different and you need here a multiple of 80.
# The default is to have no dsp_poll option, then the dsp itself
# finds out which option is the best to use by itself
#
# pcm=<number>
#
# Give the id of the PCM bus. All PCM busses with the same ID
# are expected to be connected and have equal slots.
# Only one chip of the PCM bus must be master, the others slave.
#
# debug=<number>
#
# Enable debugging (see hfc_multi.h for debug options).
#
# dsp_options=<number>
#
# set this to 2 and you'll have software bridging instead of
# hardware bridging.
#
#
# dtmftreshold=<milliseconds>
#
# Here you can tune the sensitivity of the dtmf tone recognizer.
#
poll=128
#dsp_poll=128
dsp_options=0
dtmftreshold=100
debug=0