rendered paste body#sho dsl inte
Iola_Router#sho dsl interface atm0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.2 (G.Lite)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'GSPN'
Vendor Specific: 0x0000 0x0003
Vendor Country: 0x00 0x00
Capacity Used: 95% 100%
Noise Margin: 6.5 dB 4.0 dB
Output Power: 17.0 dBm 12.0 dBm
Attenuation: 21.0 dB 21.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 1165339 (2 spurious)
Activations: 130
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 3616 0 864 0
Reed-Solomon EC: 0 0 176 0
CRC Errors: 0 0 1 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 8 8 8 A A B B B B
10: B C C C C C C C B A 9 9 9 9 0 0
20: 0 0 0 0 0 0 2 3 4 5 6 6 7 7 7 8
30: 8 9 9 9 A A A A B B B B B C C C
40: 0 C C C C C C C C C C D D D D D
50: D D D C D C C C C C C C C C C 2
60: C C C C C C C C C C C C C C C C
70: C C C C C C C C C C C C C C C C
80: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
90: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
B0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Log file of training sequence:
Power on the line is -13.356 dBm
tone detected = 40
-->SNR (lin) = 467.829
Power on the line is -18.901 dBm
tone detected = 56
-->SNR (lin) = 237.530
Power on the line is -18.195 dBm
tone detected = 64
-->SNR (lin) = 182.346
AME: peerModemFound at time : 2145
--- Activator --- REPORT MODEMLINECONTROLLER notify : ITU_HS_FOUND
PeerModemDetector::stopTranceiver
_active_detectionMode == ADM_DETECT_ITU
HS : TRELLIS_IN_LITE_IMPLEMENTED = #0x0#
==>>HsSegPool: getFreeSegment: returned [0] =
==>>HsSegPool: getFreeSegment: returned [1] =
** HS DL notify state *** enter : 0
** HS DL notify state *** enter : 1
Start HandshakeSequence
Installing initial TEQ coefficients
new gain: 1800 /100
HandshakeSequence(commmon): new gain = 1855 /100
RxGain before C-TONE
AnalogInterface : Message transfered after filtering 0x0x6200
AnalogInterface : Message transfered after filtering 0x0x5002
AnalogInterface : Message transfered after filtering 0x0x5002
doing power measurement on C-TONES
Power on the line is -13.354 dBm
tone detected = 40
-->SNR (lin) = 512.757
Power on the line is -18.903 dBm
tone detected = 56
-->SNR (lin) = 260.488
Power on the line is -18.190 dBm
tone detected = 64
-->SNR (lin) = 200.681
CTones end of detection : 1,40
doCtonesProcessing, measuredPower = 1048576.000
RMS line single = 98.418
handshakeSequence(nt): new gain = 2397 /100
handshakeSequence(nt): new gain = 3097 /100
RxGain after C-TONE
AnalogInterface : Message transfered after filtering 0x0x6800
Handshake pilot tone: 40
gain scale factor 0.962
g1, g2 : 491,24857
DPLL (g1 = 491, g2= 24857) : freq error = 1.85189208984375e1 ppm, dpll_loop acc = 0x136E
AnalogInterface : Message transfered after filtering 0x0x5342
Remaining frequency error 20.518
DPLL (g1 = 491, g2= 24857) : freq error = 4.840087890625e0 ppm, dpll_loop acc = 0x512
[before 4QAM - 2BAM] : Remaining frequency error 4.840
4QAM : x = 8227.000, y = 8156.000
DPLL (g1 = 491, g2= 24857) : freq error = 3.142333984375e0 ppm, dpll_loop acc = 0x34C
Remaining frequency error = 3.142
Doing phase rotation
installing demodulation
** HS DL notify state *** enter : 3
sending RTone1
pvoTimeRTone1: 2621
enable counter reload
HS BIT-BYTE sync :: GALF detected.
HS BIT-BYTE sync :: GALF detected.
HS :: send flags.
** HS DL notify state *** enter : 4
==>>HsSegPool: getFreeSegment: returned [2] =
###### HsProtTimer :: timer not running #####.
==>>HsSegPool: releaseSegment: found [2] =
###### HsProtTimer :: timer not running #####.
==>>HsSegPool: releaseSegment: found [0] =
==>>HsSegPool: getFreeSegment: returned [0] =
==>>HsSegPool: getFreeSegment: returned [2] =
==>>HsSegPool: getFreeSegment: returned [3] =
==>>HsSegPool: releaseSegment: found [0] =
==>>HsSegPool: releaseSegment: found [2] =
###### HsProtTimer :: timer not running #####.
==>>HsSegPool: releaseSegment: found [1] =
==>>HsSegPool: getFreeSegment: returned [0] =
==>>HsSegPool: getFreeSegment: returned [1] =
==>>HsSegPool: releaseSegment: found [0] =
###### HsProtTimer :: timer not running #####.
==>>HsSegPool: releaseSegment: found [3] =
==>>HsSegPool: getFreeSegment: returned [0] =
==>>HsSegPool: getFreeSegment: returned [2] =
==>>HsSegPool: getFreeSegment: returned [3] =
==>>HsSegPool: releaseSegment: found [0] =
==>>HsSegPool: releaseSegment: found [2] =
###### HsProtTimer :: timer not running #####.
==>>HsSegPool: releaseSegment: found [1] =
** HS DL notify state *** enter : 5
==>>HsSegPool: getFreeSegment: returned [0] =
disable Transmit Soc channel -> send quiet.
disable Receive Soc channel.
==>>HsSegPool: releaseSegment: found [0] =
==>>HsSegPool: releaseSegment: found [2] =
==>>HsSegPool: releaseSegment: found [3] =
==>>HsSegPool: releaseSegment: found [0] =
** HS DL notify state *** enter : 6
*** start INITIALIZING ***
+++ TRAINING +++
vendor code: 0x4753504E
version code: 0x3
Installing initial TEQ coefficients
AnalogInterface : Message transfered after filtering 0x0x5342
AnalogInterface : Message transfered after filtering 0x0x5342
RxGain MID before C-REVERB1
AGC phase : 1 , 'gain'=7.592
WARNING !!! getRxBPFGain function is used only for ADSF and ADSG.....
AnalogInterface : Message transfered after filtering 0x0x2180
Putting analog gain to 7 dB
Putting FFT scale to 5
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
dyn threshold: -33.354
Power on the line is -25.925 dBm
Pilot detected -->SNR (lin) = 176506.096
C_PILOT detected
TrainingSequence::adaptPilotFeq
pilot = 64
x = 484.562
y = -1525.375
scale = 7.238
installing DPLL coefficients
DPLL (g1 = 274, g2= 18575) : freq error = 2.52801513671875e0 ppm, dpll_loop acc = 0x2A7
AnalogInterface : Message transfered after filtering 0x0x5402
DPLL (g1 = 154, g2= 13931) : freq error = -2.29345703125e0 ppm, dpll_loop acc = 0xFD98
DPLL (g1 = 86, g2= 10448) : freq error = -2.34930419921875e0 ppm, dpll_loop acc = 0xFD89
ToneTriggerModule: enable recording of C_REVERB1
P_Rx = 3.435808658599853515e8
P_echo = 2.360100269317626953e4
P_tot = 3.436044216156005859e8
P_RxBoost = 1.384931449890136718e9
AnalogInterface : Message transfered after filtering 0x0x4100
Putting analog gain to 11 dB
Putting FFT scale to 5
+++ ANALYSIS +++
Pilot rescale ...
x = -7221.312
y = 7184.187
scale = 1.137
Echo Measurement ...
DcOffset value : -2.24655032157897949e2
Channel Measurement ...
DcOffset value : -2.25323724746704101e2
First TEQ-FEQ calculation
!! FIRST_MEDLEY_TONE_INTEROP_MASKING 220 : DELTA_SNR_INTEROP_MASKING = 2
do NOT MASK tone 242
do NOT MASK tone 243
do NOT MASK tone 244
do NOT MASK tone 245
do NOT MASK tone 246
do NOT MASK tone 247
do NOT MASK tone 248
do NOT MASK tone 249
do NOT MASK tone 250
do NOT MASK tone 251
do NOT MASK tone 252
do NOT MASK tone 253
do NOT MASK tone 254
do NOT MASK tone 255
P_Rx = 1.105629086494445800e9
P_echo = 4.678012847900390625e2
P_tot = 1.105629444122314453e9
Calculated window move parameter : 332
*** Start EXCHANGE ***
New PILOT has carrier number 60
RTV value for segue detection : 37
+++ start transmitSequence +++
enable synchronuous schedule swap
Seque symbol detected at sync 89 and symb 7
C_MESSAGES1 received completely
Psd down: -40
Target NM: 6
Downstream option #0 interl : 224
Downstream option #0 fast : 0
Downstream option #0 RS interl:16
Downstream option #0 2*S : 2
Downstream option #0 Idepth : 64
Downstream option #1 interl : 149
Downstream option #1 fast : 0
Downstream option #1 RS interl:16
Downstream option #1 2*S : 2
Downstream option #1 Idepth : 64
Downstream option #2 interl : 75
Downstream option #2 fast : 0
Downstream option #2 RS interl:8
Downstream option #2 2*S : 4
Downstream option #2 Idepth : 32
Downstream option #3 interl : 1
Downstream option #3 fast : 0
Downstream option #3 RS interl:1
Downstream option #3 2*S : 32
Downstream option #3 Idepth : 2
---------------------------------------------------------------
MODEM INITIALIZING IN OPERATION MODE G_LITE !!!!!
INITIALIZATION SPECIFICATIONS : STANDARD COMPLIANT INITIATIZATION !!!!!
INITIALIZATION SPECIFICATIONS : MINUMUM OVERHEAD FRAMING !!!!!
---------------------------------------------------------------
AnalogInterface : Message transfered after filtering 0x0x7402
build R_MESSAGES1
New PILOT has carrier number 95
force counter reload
TransmitSequence: Counter reload event
Calculate final TEQ
Calculate final window move
TEQ-FEQ : DcOffset value : -1.02489018440246582e3
FSE after TEQ: 5
RTV value for segue detection : 109
SNR Measurement ...
enable counter reload
SNR measurement ...
Calculating max capacity ...
SNR medley:
38: 15 19 22 25 27 29 30 31 32 33
48: 34 35 37 38 39 39 40 41 42 42
58: 43 44 44 45 45 45 0 46 46 46
68: 47 47 47 47 47 47 47 47 47 47
78: 47 47 47 47 47 47 47 47 47 47
88: 47 47 47 47 47 47 46 47 47 47
98: 47 47 47 47 47 47 47 47 47 47
108: 47 47 47 47 47 47 47 47 47 47
118: 47 47 47 47 47 47 47 47 47 47
maxPower = 112.044
Max capacity Execution time = 14 ms
Total_number_of_bits_supported = 876
Performance_Margin = 4.500 dB
uncoded snr: 633 coded snr: 633 averageBi : 10
Coding Gain (in units of 0.5 dB : 4
Build R_MESSAGES_RA
enable counter reload
TransmitSequence: Counter reload event
Seque symbol detected at sync 232 and symb 52
decode C_MESSAGES_RA
Extract parameters from C_MESSAGES_RA
option 0:
0 0 0 0 0 0 0 0 0 0 113 0 0 0 0 0 0 28 0 0 0 8 2 16 0 0 2 8 4 0
Downstream option #0 interl : 113
Downstream option #0 fast : 0
Downstream option #0 RS interl:8
Downstream option #0 2*S : 4
Downstream option #0 Idepth : 16
option 1:
0 0 0 0 0 0 0 0 0 0 109 0 0 0 0 0 0 27 0 0 0 8 2 16 0 0 2 8 4 0
Downstream option #1 interl : 109
Downstream option #1 fast : 0
Downstream option #1 RS interl:8
Downstream option #1 2*S : 4
Downstream option #1 Idepth : 16
option 2:
0 0 0 0 0 0 0 0 0 0 105 0 0 0 0 0 0 23 0 0 0 8 2 16 0 0 2 8 4 0
Downstream option #2 interl : 105
Downstream option #2 fast : 0
Downstream option #2 RS interl:8
Downstream option #2 2*S : 4
Downstream option #2 Idepth : 16
option 3:
0 0 0 0 0 0 0 0 0 0 91 0 0 0 0 0 0 19 0 0 0 16 1 64 0 0 2 8 4 0
Downstream option #3 interl : 91
Downstream option #3 fast : 0
Downstream option #3 RS interl:16
Downstream option #3 2*S : 2
Downstream option #3 Idepth : 64
requested noise margin = 6
requested max noise margin = 0
requested min noise margin = 0
Data rate option selection
SNR medley:
38: 15 19 22 25 27 29 30 31 32 33
48: 34 35 37 38 39 39 40 41 42 42
58: 43 44 44 45 45 45 0 46 46 46
68: 47 47 47 47 47 47 47 47 47 47
78: 47 47 47 47 47 47 47 47 47 47
88: 47 47 47 47 47 47 46 47 47 47
98: 47 47 47 47 47 47 47 47 47 47
108: 47 47 47 47 47 47 47 47 47 47
118: 47 47 47 47 47 47 47 47 47 47
maxPower = 112.044
Max_number_of_bits_supported = 1028
Build R_MESSAGE2
enable counter reload
Calculating final capacity ...
results BIGI algorithm:
tone bi gi mi
38 2 1 7
39 3 2 6
40 4 1 7
41 5 1 6
42 6 2 6
43 6 0 6
44 7 2 6
45 7 1 6
46 7 0 6
47 8 2 6
48 8 0 6
49 9 2 6
50 9 1 6
51 9 0 6
52 10 2 6
53 10 1 6
54 10 0 6
55 10 0 6
56 11 2 6
57 11 1 6
58 11 0 6
59 11 0 6
60 11 0 6
61 12 2 6
62 12 1 6
63 12 1 6
64 0 0 0
65 12 1 7
66 12 0 6
67 12 0 6
68 12 0 6
69 12 0 6
70 12 0 6
71 12 0 6
72 12 0 6
73 12 0 7
74 12 0 6
75 13 2 6
76 13 2 6
77 13 2 6
78 13 2 6
79 13 2 6
80 13 2 6
81 13 2 6
82 13 2 6
83 12 0 6
84 13 2 6
85 12 0 6
86 12 0 6
87 12 0 7
88 12 0 6
89 12 0 6
90 12 0 6
91 12 0 6
92 12 0 6
93 12 0 6
94 12 0 6
95 2 0 36
96 12 0 6
97 12 0 6
98 12 0 6
99 12 0 6
100 12 0 6
101 12 0 6
102 12 0 6
103 12 0 6
104 12 0 6
105 12 0 6
106 12 0 6
107 12 0 7
108 12 0 6
109 12 0 7
110 12 0 6
111 12 0 6
112 12 0 6
113 12 0 6
114 12 0 7
115 12 0 6
116 12 0 6
117 12 0 6
118 12 0 6
119 12 0 7
120 12 0 6
121 12 0 6
122 12 0 6
123 12 0 6
124 12 0 6
125 12 0 6
126 12 0 6
127 12 0 6
final capacity execution time = 24 ms )
Final_number_of_bits_supported = 976
Requested_number_of_bits = 976
Performance_Margin = 6.000 dB
Selected Option = 0
TransmitSequence: Counter reload event
Seque symbol detected at sync 6 and symb 100
C_MESSAGES2 received completely
force counter reload
Build R_BIGI
Prepare Receive SHOWTIME
force counter reload
enable synchronuous schedule swap
TransmitSequence: Counter reload event
Prepare Transmit SHOWTIME
Ftg value for sync : 21852
enable synchronuous schedule swap
*** start RUNTIME ***
Showtime SNR monitoring will be started
setMaskMain on interruptDispatcher
DPLL (g1 = 87, g2= 10466) : freq error = -2.25250244140625e0 ppm, dpll_loop acc = 0xFDA3
DC offset: -1.02413833141326904e3
MNM=86 ANM=102
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
MNM=86 ANM=102
MNM=86 ANM=101
MNM=84 ANM=101
MNM=86 ANM=101
DPLL (g1 = 87, g2= 10466) : freq error = -2.29718017578125e0 ppm, dpll_loop acc = 0xFD97
DC offset: -1.02408909797668457e3
MNM=86 ANM=101
MNM=85 ANM=100
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
MNM=87 ANM=101
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out
Aoc fifo A will be read out
Aoc fifo B will be read out