rendered paste body[ 0.000000] Linux version 2.6.18.2.20070115.1 (root@satcom) (gcc version 3.4.6 (Ubuntu 3.4.6-3ubuntu1)) #1 SMP Mon Jan 15 10:46:14 EST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
[ 0.000000] BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fbc70
[ 0.000000] On node 0 totalpages: 65520
[ 0.000000] DMA zone: 4096 pages, LIFO batch:0
[ 0.000000] Normal zone: 61424 pages, LIFO batch:15
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 AMI ) @ 0x000faa60
[ 0.000000] ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff0000
[ 0.000000] ACPI: FADT (v001 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x0fff0030
[ 0.000000] ACPI: MADT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff00c0
[ 0.000000] ACPI: DSDT (v001 SiS 746 0x00000100 INTL 0x02002024) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
[ 0.000000] Detected 1672.450 MHz processor.
[ 22.901903] Built 1 zonelists. Total pages: 65520
[ 22.901907] Kernel command line: root=/dev/hda1 ro quiet splash
[ 22.902107] mapped APIC to ffffd000 (fee00000)
[ 22.902110] mapped IOAPIC to ffffc000 (fec00000)
[ 22.902114] Enabling fast FPU save and restore... done.
[ 22.902116] Enabling unmasked SIMD FPU exception support... done.
[ 22.902119] Initializing CPU#0
[ 22.902187] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 22.903322] Console: colour VGA+ 80x25
[ 22.903563] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 22.903744] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 22.912994] Memory: 255028k/262080k available (2327k kernel code, 6592k reserved, 1292k data, 228k init, 0k highmem)
[ 22.912999] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 22.990155] Calibrating delay using timer specific routine.. 3346.83 BogoMIPS (lpj=6693671)
[ 22.990207] Security Framework v1.0.0 initialized
[ 22.990214] SELinux: Disabled at boot.
[ 22.990234] Mount-cache hash table entries: 512
[ 22.990411] CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 22.990419] CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 22.990428] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 22.990432] CPU: L2 Cache: 256K (64 bytes/line)
[ 22.990434] CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
[ 22.990443] Compat vDSO mapped to ffffe000.
[ 22.990457] Checking 'hlt' instruction... OK.
[ 23.006243] SMP alternatives: switching to UP code
[ 23.006450] Freeing SMP alternatives: 16k freed
[ 23.006456] ACPI: Core revision 20060707
[ 23.008970] CPU0: AMD Sempron(tm) 2400+ stepping 01
[ 23.008996] Total of 1 processors activated (3346.83 BogoMIPS).
[ 23.009119] ENABLING IO-APIC IRQs
[ 23.009278] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 23.154158] Brought up 1 CPUs
[ 23.154187] migration_cost=0
[ 23.154697] NET: Registered protocol family 16
[ 23.154812] ACPI: bus type pci registered
[ 23.155483] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
[ 23.155492] PCI: Using configuration type 1
[ 23.155495] Setting up standard PCI resources
[ 23.161013] ACPI: Interpreter enabled
[ 23.161019] ACPI: Using IOAPIC for interrupt routing
[ 23.161548] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 23.161554] PCI: Probing PCI hardware (bus 00)
[ 23.163594] Uncovering SIS963 that hid as a SIS503 (compatible=0)
[ 23.163598] Enabling SiS 96x SMBus.
[ 23.164176] Boot video device is 0000:01:00.0
[ 23.164241] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 23.181341] ACPI: Power Resource [URP1] (off)
[ 23.181421] ACPI: Power Resource [URP2] (off)
[ 23.181503] ACPI: Power Resource [FDDP] (off)
[ 23.181582] ACPI: Power Resource [LPTP] (off)
[ 23.182732] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 23.183011] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 23.183288] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 23.183567] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 23.183847] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 23.184124] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 23.184402] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 23.184680] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 23.184817] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 23.184840] pnp: PnP ACPI init
[ 23.188164] pnp: PnP ACPI: found 10 devices
[ 23.188236] PCI: Using ACPI for IRQ routing
[ 23.188240] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 23.192103] PCI: Bridge: 0000:00:01.0
[ 23.192106] IO window: disabled.
[ 23.192113] MEM window: cdd00000-cfefffff
[ 23.192118] PREFETCH window: bda00000-cdbfffff
[ 23.192170] NET: Registered protocol family 2
[ 23.230178] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 23.230302] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 23.230430] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 23.230497] TCP: Hash tables configured (established 8192 bind 4096)
[ 23.230500] TCP reno registered
[ 23.231366] audit: initializing netlink socket (disabled)
[ 23.231382] audit(1178663914.408:1): initialized
[ 23.231534] VFS: Disk quotas dquot_6.5.1
[ 23.231568] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 23.231673] Initializing Cryptographic API
[ 23.231679] io scheduler noop registered
[ 23.231686] io scheduler anticipatory registered
[ 23.231692] io scheduler deadline registered
[ 23.231705] io scheduler cfq registered (default)
[ 23.261632] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 23.261782] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.262711] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.263636] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 23.263885] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 23.263890] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 23.263948] SIS5513: IDE controller at PCI slot 0000:00:02.5
[ 23.263969] SIS5513: chipset revision 0
[ 23.263971] SIS5513: not 100% native mode: will probe irqs later
[ 23.263984] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[ 23.263998] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[ 23.264013] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
[ 23.264024] Probing IDE interface ide0...
[ 23.550081] hda: Maxtor 6E040L0, ATA DISK drive
[ 24.221849] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 24.221963] Probing IDE interface ide1...
[ 24.509700] hdc: Maxtor 6B200P0, ATA DISK drive
[ 25.182834] ide1 at 0x170-0x177,0x376 on irq 15
[ 25.183524] hda: max request size: 128KiB
[ 25.198046] hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
[ 25.198172] hda: cache flushes supported
[ 25.198214] hda: hda1 hda2 < hda5 >
[ 25.225952] hdc: max request size: 512KiB
[ 25.248562] hdc: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63, UDMA(133)
[ 25.250120] hdc: cache flushes supported
[ 25.250139] hdc: hdc1 hdc2 < hdc5 >
[ 25.282523] PNP: No PS/2 controller found. Probing ports directly.
[ 25.308940] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 25.309059] mice: PS/2 mouse device common for all mice
[ 25.309173] TCP bic registered
[ 25.309182] NET: Registered protocol family 1
[ 25.309192] NET: Registered protocol family 8
[ 25.309194] NET: Registered protocol family 20
[ 25.309236] Using IPI No-Shortcut mode
[ 25.309326] ACPI: (supports S0 S1 S4 S5)
[ 25.313240] Time: tsc clocksource has been installed.
[ 25.338429] kjournald starting. Commit interval 5 seconds
[ 25.338442] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.338485] VFS: Mounted root (ext3 filesystem) readonly.
[ 25.338824] Freeing unused kernel memory: 228k freed
[ 33.232846] input: PC Speaker as /class/input/input0
[ 33.361852] usbcore: registered new driver usbfs
[ 33.361896] usbcore: registered new driver hub
[ 33.383210] Floppy drive(s): fd0 is 1.44M
[ 33.405545] FDC 0 is a post-1991 82077
[ 33.432119] parport: PnPBIOS parport detected.
[ 33.432228] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 33.445484] Real Time Clock Driver v1.12ac
[ 33.454597] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 33.469447] 8139too Fast Ethernet driver 0.9.27
[ 33.469527] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 169
[ 33.469906] eth0: RealTek RTL8139 at 0xd0896f00, 00:40:f4:ec:0c:de, IRQ 169
[ 33.469910] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 33.475165] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[ 33.502088] Linux agpgart interface v0.101 (c) Dave Jones
[ 33.511765] agpgart: Detected SiS 741 chipset
[ 33.516958] agpgart: AGP aperture is 64M @ 0xd0000000
[ 33.588666] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 33.588733] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 177
[ 33.588751] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 33.589278] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 33.589311] ohci_hcd 0000:00:03.0: irq 177, io mem 0xcfffd000
[ 33.644115] usb usb1: configuration #1 chosen from 1 choice
[ 33.644161] hub 1-0:1.0: USB hub found
[ 33.644179] hub 1-0:1.0: 3 ports detected
[ 33.746018] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 185
[ 33.746035] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 33.746075] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 33.746091] ohci_hcd 0000:00:03.1: irq 185, io mem 0xcfffe000
[ 33.803973] usb usb2: configuration #1 chosen from 1 choice
[ 33.804016] hub 2-0:1.0: USB hub found
[ 33.804029] hub 2-0:1.0: 3 ports detected
[ 33.904996] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 33.906185] ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) -> IRQ 193
[ 33.906209] ehci_hcd 0000:00:03.2: EHCI Host Controller
[ 33.906257] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 33.906309] PCI: cache line size of 64 is not supported by device 0000:00:03.2
[ 33.906327] ehci_hcd 0000:00:03.2: irq 193, io mem 0xcffff000
[ 33.906335] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 33.906483] usb usb3: configuration #1 chosen from 1 choice
[ 33.906531] hub 3-0:1.0: USB hub found
[ 33.906545] hub 3-0:1.0: 6 ports detected
[ 34.034901] nvidia: module license 'NVIDIA' taints kernel.
[ 34.041064] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
[ 34.041614] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-7184 Tue Aug 1 18:38:58 PDT 2006
[ 34.079733] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 209
[ 34.393657] intel8x0_measure_ac97_clock: measured 55826 usecs
[ 34.393662] intel8x0: clocking to 48000
[ 34.599832] NET: Registered protocol family 17
[ 34.616503] Capability LSM initialized
[ 34.734186] Adding 746980k swap on /dev/disk/by-uuid/294f34b4-2b19-44b2-bad6-dc5a0e8ff394. Priority:-1 extents:1 across:746980k
[ 68.230430] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 68.230439] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 68.230443] ide: failed opcode was: unknown
[ 68.272123] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 68.272128] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 68.272131] ide: failed opcode was: unknown
[ 108.184659] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 108.184667] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 108.184672] ide: failed opcode was: unknown
[ 108.184793] EXT3 FS on hda1, internal journal
[ 113.330047] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 113.330056] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 113.330060] ide: failed opcode was: unknown
[ 113.371739] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 113.371744] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 113.371747] ide: failed opcode was: unknown
[ 113.413436] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 113.413440] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 113.413443] ide: failed opcode was: unknown
[ 113.455133] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 113.455138] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 113.455140] ide: failed opcode was: unknown
[ 113.506369] ide0: reset: success
[ 116.218437] ACPI: Power Button (FF) [PWRF]
[ 116.218450] ACPI: Power Button (CM) [PWRB]
[ 116.231988] Using specific hotkey driver
[ 116.318303] ibm_acpi: ec object not found
[ 116.363593] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 117.667994] lp0: using parport0 (interrupt-driven).
[ 117.793887] ppdev: user-space parallel port driver
[ 118.776635] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 118.776772] agpgart: Device is in legacy mode, falling back to 2.x
[ 118.776865] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 118.776988] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 119.401104] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 119.401115] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 119.401120] ide: failed opcode was: unknown
[ 119.451137] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 119.451142] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 119.451146] ide: failed opcode was: unknown
[ 119.576521] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 119.576666] agpgart: Device is in legacy mode, falling back to 2.x
[ 119.576757] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 119.576880] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 122.044531] apm: BIOS not found.
[ 132.618996] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.619009] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.619014] ide: failed opcode was: unknown
[ 132.660694] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.660707] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.660711] ide: failed opcode was: unknown
[ 132.702389] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.702402] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.702407] ide: failed opcode was: unknown
[ 132.744086] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.744099] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.744104] ide: failed opcode was: unknown
[ 132.794745] ide0: reset: success
[ 132.835816] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.835826] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.835831] ide: failed opcode was: unknown
[ 132.877512] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.877522] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.877527] ide: failed opcode was: unknown
[ 132.919208] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.919219] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.919223] ide: failed opcode was: unknown
[ 132.960906] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 132.960917] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 132.960921] ide: failed opcode was: unknown
[ 133.010665] ide0: reset: success
[ 133.052641] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.052654] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.052658] ide: failed opcode was: unknown
[ 133.052665] end_request: I/O error, dev hda, sector 8143
[ 133.094335] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.094346] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.094350] ide: failed opcode was: unknown
[ 133.136037] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.136052] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.136057] ide: failed opcode was: unknown
[ 133.177733] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.177743] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.177748] ide: failed opcode was: unknown
[ 133.219430] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.219440] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.219445] ide: failed opcode was: unknown
[ 133.270554] ide0: reset: success
[ 133.377875] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.377888] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.377892] ide: failed opcode was: unknown
[ 133.434781] Aborting journal on device hda1.
[ 133.435026] journal commit I/O error
[ 133.435267] ext3_abort called.
[ 133.435271] EXT3-fs error (device hda1): ext3_journal_start_sb: Detected aborted journal
[ 133.435275] Remounting filesystem read-only
[ 133.586360] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.586370] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.586374] ide: failed opcode was: unknown
[ 133.591238] EXT3-fs error (device hda1) in ext3_reserve_inode_write: Journal has aborted
[ 133.703111] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.703124] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.703129] ide: failed opcode was: unknown
[ 133.761487] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.761500] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.761505] ide: failed opcode was: unknown
[ 133.828201] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.828214] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.828219] ide: failed opcode was: unknown
[ 133.886576] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 133.886587] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 133.886592] ide: failed opcode was: unknown
[ 133.938298] ide0: reset: success
[ 134.003328] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.003342] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.003347] ide: failed opcode was: unknown
[ 134.061705] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.061719] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.061724] ide: failed opcode was: unknown
[ 134.128416] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.128429] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.128434] ide: failed opcode was: unknown
[ 134.186793] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.186806] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.186811] ide: failed opcode was: unknown
[ 134.238180] ide0: reset: success
[ 134.303542] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.303555] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.303560] ide: failed opcode was: unknown
[ 134.303568] end_request: I/O error, dev hda, sector 30146775
[ 134.303576] Buffer I/O error on device hda1, logical block 3768339
[ 134.303580] lost page write due to I/O error on hda1
[ 134.314165] EXT3-fs error (device hda1) in ext3_reserve_inode_write: Journal has aborted
[ 134.361921] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.361933] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.361938] ide: failed opcode was: unknown
[ 134.420296] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.420310] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.420315] ide: failed opcode was: unknown
[ 134.478670] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.478683] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.478688] ide: failed opcode was: unknown
[ 134.537046] hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[ 134.537058] hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
[ 134.537063] ide: failed opcode was: unknown
[ 134.586037] ide0: reset: success
[ 134.854688] Bluetooth: Core ver 2.10
[ 134.854766] NET: Registered protocol family 31
[ 134.854769] Bluetooth: HCI device and connection manager initialized
[ 134.854773] Bluetooth: HCI socket layer initialized
[ 135.079277] Bluetooth: L2CAP ver 2.8
[ 135.079284] Bluetooth: L2CAP socket layer initialized
[ 135.212991] Bluetooth: RFCOMM socket layer initialized
[ 135.213014] Bluetooth: RFCOMM TTY layer initialized
[ 135.213016] Bluetooth: RFCOMM ver 1.8
[ 1632.044517] ext3_abort called.
[ 1632.044532] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1632.045861] ext3_abort called.
[ 1632.045875] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1638.032189] ext3_abort called.
[ 1638.032206] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1638.033502] ext3_abort called.
[ 1638.033517] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1642.097153] ext3_abort called.
[ 1642.097170] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1642.098428] ext3_abort called.
[ 1642.098437] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1648.789070] ext3_abort called.
[ 1648.789087] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1658.382861] ext3_abort called.
[ 1658.382878] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1658.383945] ext3_abort called.
[ 1658.383953] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1663.299391] ext3_abort called.
[ 1663.299409] EXT3-fs error (device hda1): ext3_remount: Abort forced by user
[ 1663.300814] ext3_abort called.
[ 1663.300828] EXT3-fs error (device hda1): ext3_remount: Abort forced by user