rendered paste body$ dmesg
Linux version 2.6.20.11-1.smp.gcc3.4.x86.i686 (kernelbits.rpath.org@rpl:1) (gcc version 3.4.4) #1 SMP Fri May 4 11:27:57 EDT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fd80000 end: 000000001fe80000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fe80000 size: 0000000000009000 end: 000000001fe89000 type: 3
copy_e820_map() start: 000000001fe89000 size: 0000000000077000 end: 000000001ff00000 type: 4
copy_e820_map() start: 000000001ff00000 size: 0000000000100000 end: 0000000020000000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010006000 end: 00000000f0006000 type: 2
copy_e820_map() start: 00000000f0008000 size: 0000000000004000 end: 00000000f000c000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000070000 end: 00000000fed90000 type: 2
copy_e820_map() start: 00000000ff000000 size: 0000000001000000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fe80000 (usable)
BIOS-e820: 000000001fe80000 - 000000001fe89000 (ACPI data)
BIOS-e820: 000000001fe89000 - 000000001ff00000 (ACPI NVS)
BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
Entering add_active_range(0, 0, 130688) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130688
HighMem 130688 -> 130688
early_node_map[1] active PFN ranges
0: 0 -> 130688
On node 0 totalpages: 130688
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 989 pages used for memmap
Normal zone: 125603 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI present.
Using APIC driver default
ACPI: RSDP (v000 PTLTD ) @ 0x000f6a00
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fe810a9
ACPI: FADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x1fe88e8a
ACPI: MADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x1fe88efe
ACPI: HPET (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x1fe88f64
ACPI: MCFG (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x1fe88f9c
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1fe88fd8
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030224) @ 0x1fe814de
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x1fe81306
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x1fe810ed
ACPI: DSDT (v001 INTEL ALVISO 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x02] address[0xfec20000] gsi_base[24])
IOAPIC[1]: apic_id 2, version 255, address 0xfec20000, GSI 24-279
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0x0
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1596.054 MHz processor.
Built 1 zonelists. Total pages: 129667
Kernel command line: ro root=/dev/hda5 quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec20000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511736k/522752k available (2154k kernel code, 10524k reserved, 906k data, 232k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdfe80000 ( 510 MB)
.init : 0xc0704000 - 0xc073e000 ( 232 kB)
.data : 0xc061a9a8 - 0xc06fd3f4 ( 906 kB)
.text : 0xc0400000 - 0xc061a9a8 (2154 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3195.51 BogoMIPS (lpj=5324016)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
Total of 1 processors activated (3195.51 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd7be, last bus=7
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#08) is hidden behind transparent bridge #06 (-#07) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.2
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.2
PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.2
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: c8100000-c81fffff
PREFETCH window: d0000000-d7ffffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:01.0
IO window: 00004000-000040ff
IO window: 00004400-000044ff
PREFETCH window: 30000000-33ffffff
MEM window: 34000000-37ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 4000-4fff
MEM window: c8200000-c82fffff
PREFETCH window: 30000000-33ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 18 (level, low) -> IRQ 18
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2198k freed
Simple Boot Flag at 0x36 set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1178616828.136:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Thermal Zone [THRM] (35 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 19
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x18c0-0x18c7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: IC25N080ATMR04-0, ATA DISK drive
hdb: MATSHITAUJ-840D, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 > hda4
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 232k freed
Time: tsc clocksource has been installed.
Time: acpi_pm clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps: 0xa04713/0x4000
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xc8000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
input: SynPS/2 Synaptics TouchPad as /class/input/input1
input: AT Translated Set 2 keyboard as /class/input/input2
SCSI subsystem initialized
libata version 2.00 loaded.
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
intel_rng: FWH not detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 21
input: PC Speaker as /class/input/input3
tg3.c:v3.72 (January 8, 2007)
ACPI: PCI Interrupt 0000:06:08.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:c0:9f:7c:38:e0
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
ACPI: PCI Interrupt 0000:06:01.2[A] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[c8217000-c82177ff] Max Packet=[2048] IR/IT contexts=[4/8]
Yenta: CardBus bridge found at 0000:06:01.0 [1025:0066]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:01.0, mfunc 0x00c21b22, devctl 0x64
Yenta: ISA IRQ mask 0x0cf8, PCI irq 18
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #08
pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
cs: IO port probe 0x4000-0x4fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc8200000 - 0xc82fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1e.3 to 64
MC'97 0 converters and GPIO not ready (0x1)
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1e.2 to 64
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
intel8x0_measure_ac97_clock: measured 50714 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:06:01.3[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 17 (level, low) -> IRQ 17
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00004492d2]
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
[fglrx] module loaded - fglrx 8.34.8 [Feb 20 2007] on minor 0
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input7
ACPI: Sleep Button (CM) [SLPB]
ACPI: ACPI Dock Station Driver
Using specific hotkey driver
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1132540k swap on /dev/hda6. Priority:-1 extents:1 across:1132540k
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
PM: Writing back config space on device 0000:06:08.0 at offset b (was 3ed173b, writing 661025)
PM: Writing back config space on device 0000:06:08.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:06:08.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:06:08.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:06:08.0 at offset 0 (was 3ed173b, writing 169c14e4)
PM: Writing back config space on device 0000:06:08.0 at offset b (was 3ed173b, writing 661025)
PM: Writing back config space on device 0000:06:08.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:06:08.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:06:08.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:06:08.0 at offset 0 (was 3ed173b, writing 169c14e4)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[fglrx] total GART = 130023424
[fglrx] free GART = 114032640
[fglrx] max single GART = 114032640
[fglrx] total LFB = 66977792
[fglrx] free LFB = 52588544
[fglrx] max single LFB = 52588544
[fglrx] total Inv = 0
[fglrx] free Inv = 0
[fglrx] max single Inv = 0
[fglrx] total TIM = 0
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
PM: Writing back config space on device 0000:06:08.0 at offset b (was 3ed173b, writing 661025)
PM: Writing back config space on device 0000:06:08.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:06:08.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:06:08.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:06:08.0 at offset 0 (was 3ed173b, writing 169c14e4)
ADDRCONF(NETDEV_UP): eth0: link is not ready
ieee80211_crypt: registered algorithm 'TKIP'
eth1: no IPv6 routers present
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input8
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-2
atkbd.c: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e072 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e072 <keycode>' to make it known.
TKIP: replay detected: STA=00:16:b6:ed:e3:9c previous TSC 000000038a1c received TSC 000000038a1a
TKIP: replay detected: STA=00:16:b6:ed:e3:9c previous TSC 000000038a1c received TSC 000000038a1b
TKIP: replay detected: STA=00:16:b6:ed:e3:9c previous TSC 000000038a21 received TSC 000000038a1e
TKIP: replay detected: STA=00:16:b6:ed:e3:9c previous TSC 000000038a21 received TSC 000000038a1f
TKIP: replay detected: STA=00:16:b6:ed:e3:9c previous TSC 000000038a21 received TSC 000000038a20
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access Sony Sony DSC 4.50 PQ: 0 ANSI: 0 CCS
SCSI device sda: 126848 512-byte hdwr sectors (65 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 126848 512-byte hdwr sectors (65 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 4-2: USB disconnect, address 2
usb 4-2: new full speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usb 4-2: USB disconnect, address 3
usb 4-2: new full speed USB device using uhci_hcd and address 4
usb 4-2: configuration #1 chosen from 1 choice
usb 4-2: USB disconnect, address 4
usb 4-2: new full speed USB device using uhci_hcd and address 5
usb 4-2: configuration #1 chosen from 1 choice
usb 4-2: USB disconnect, address 5
usb 4-2: new full speed USB device using uhci_hcd and address 6
usb 4-2: configuration #1 chosen from 1 choice