I want to dial the stuff in [new1] and [new2]
;
; lba: sip.conf - SIP Configuration example for Asterisk
;
; For Asterisk 1.2+ the concept of 'user' is being phased out.
; Use 'peer' for everything.
; Syntax for specifying a SIP device in extensions.conf is
; SIP/devicename where devicename is defined in a section below.
;
; You may also use
; SIP/username@domain to call any SIP user on the Internet
; (Don't forget to enable DNS SRV records if you want to use this)
;
; If you define a SIP proxy as a peer below, you may call
; SIP/proxyhostname/user or SIP/user@proxyhostname
; where the proxyhostname is defined in a section below
;
; Useful CLI commands to check peers/users:
; sip show peers Show all SIP peers (including friends)
; sip show users Show all SIP users (including friends)
; sip show registry Show status of hosts we register with
;
; sip debug Show all SIP messages
;
; reload chan_sip.so Reload configuration file
; Active SIP peers will not be reconfigured
;
[general]
; these are what I created to allow entries in extensions.conf
context=new1
context=new2
context=default ; Default context for incoming calls
;allowguest=no ; Allow or reject guest calls (default is yes, this can also be set to 'osp'
; if asterisk was compiled with OSP support.
;realm=mydomain.tld ; Realm for digest authentication
; defaults to "asterisk"
; Realms MUST be globally unique according to RFC 3261
; Set this to your host name or domain name
bindport=5060 ; UDP Port to bind to (SIP standard port is 5060)
bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
; Note: Asterisk only uses the first host
; in SRV records
; Disabling DNS SRV lookups disables the
; ability to place SIP calls based on domain
; names to some other SIP users on the Internet
;domain=mydomain.tld ; Set default domain for this host
; If configured, Asterisk will only allow
; INVITE and REFER to non-local domains
; Use "sip show domains" to list local domains
;domain=mydomain.tld,mydomain-incoming
; Add domain and configure incoming context
; for external calls to this domain
;domain=1.2.3.4 ; Add IP address as local domain
; You can have several "domain" settings
;allowexternalinvites=no ; Disable INVITE and REFER to non-local domains
; Default is yes
;autodomain=yes ; Turn this on to have Asterisk add local host
; name and local IP to domain list.
;pedantic=yes ; Enable slow, pedantic checking for Pingtel
; and multiline formatted headers for strict
; SIP compatibility (defaults to "no")
;tos=184 ; Set IP QoS to either a keyword or numeric val
;tos=lowdelay ; lowdelay,throughput,reliability,mincost,none
;maxexpiry=3600 ; Max length of incoming registration we allow
;defaultexpiry=120 ; Default length of incoming/outoing registration
;notifymimetype=text/plain ; Allow overriding of mime type in MWI NOTIFY
;checkmwi=10 ; Default time between mailbox checks for peers
;vmexten=voicemail ; dialplan extension to reach mailbox sets the
; Message-Account in the MWI notify message
; defaults to "asterisk"
;videosupport=yes ; Turn on support for SIP video
;recordhistory=yes ; Record SIP history by default
; (see sip history / sip no history)
;disallow=all ; First disallow all codecs
;allow=ulaw ; Allow codecs in order of preference
;allow=ilbc ;
;musicclass=default ; Sets the default music on hold class for all SIP calls
; This may also be set for individual users/peers
;language=en ; Default language setting for all users/peers
; This may also be set for individual users/peers
;relaxdtmf=yes ; Relax dtmf handling
;rtptimeout=60 ; Terminate call if 60 seconds of no RTP activity
; when we're not on hold
;rtpholdtimeout=300 ; Terminate call if 300 seconds of no RTP activity
; when we're on hold (must be > rtptimeout)
;trustrpid = no ; If Remote-Party-ID should be trusted
;sendrpid = yes ; If Remote-Party-ID should be sent
;progressinband=never ; If we should generate in-band ringing always
; use 'never' to never use in-band signalling, even in cases
; where some buggy devices might not render it
;useragent=Asterisk PBX ; Allows you to change the user agent string
;promiscredir = no ; If yes, allows 302 or REDIR to non-local SIP address
; Note that promiscredir when redirects are made to the
; local system will cause loops since SIP is incapable
; of performing a "hairpin" call.
;usereqphone = no ; If yes, ";user=phone" is added to uri that contains
; a valid phone number
;dtmfmode = rfc2833 ; Set default dtmfmode for sending DTMF. Default: rfc2833
; Other options:
; info : SIP INFO messages
; inband : Inband audio (requires 64 kbit codec -alaw, ulaw)
; auto : Use rfc2833 if offered, inband otherwise
;compactheaders = yes ; send compact sip headers.
;sipdebug = yes ; Turn on SIP debugging by default, from
; the moment the channel loads this configuration
;subscribecontext = default ; Set a specific context for SUBSCRIBE requests
; Useful to limit subscriptions to local extensions
; Settable per peer/user also
;notifyringing = yes ; Notify subscriptions on RINGING state
;
; If regcontext is specified, Asterisk will dynamically create and destroy a
; NoOp priority 1 extension for a given peer who registers or unregisters with
; us. The actual extension is the 'regexten' parameter of the registering
; peer or its name if 'regexten' is not provided. More than one regexten may
; be supplied if they are separated by '&'. Patterns may be used in regexten.
;
;regcontext=sipregistrations
;
; Asterisk can register as a SIP user agent to a SIP proxy (provider)
; Format for the register statement is:
; register => user[:secret[:authuser]]@host[:port][/extension]
;
; If no extension is given, the 's' extension is used. The extension needs to
; be defined in extensions.conf to be able to accept calls from this SIP proxy
; (provider).
;
; host is either a host name defined in DNS or the name of a section defined
; below.
;
; Examples:
;
;register => 1234:password@mysipprovider.com
;
; This will pass incoming calls to the 's' extension
;
;
;register => 2345:password@sip_proxy/1234
register => sanitized
;
; Register 2345 at sip provider 'sip_proxy'. Calls from this provider
; connect to local extension 1234 in extensions.conf, default context,
; unless you configure a [sip_proxy] section below, and configure a
; context.
; Tip 1: Avoid assigning hostname to a sip.conf section like [provider.com]
; Tip 2: Use separate type=peer and type=user sections for SIP providers
; (instead of type=friend) if you have calls in both directions
;registertimeout=20 ; retry registration calls every 20 seconds (default)
;registerattempts=10 ; Number of registration attempts before we give up
; 0 = continue forever, hammering the other server until it
; accepts the registration
; Default is 0 tries, continue forever
;callevents=no ; generate manager events when sip ua performs events (e.g. hold)
;----------------------------------------- NAT SUPPORT ------------------------
;
; The externip, externhost and localnet settings are used if you use Asterisk
; behind a NAT device to communicate with services on the outside.
; Below lines added by lba after Installfest
; from aah22 sip.nat.conf which is included in sip.conf:
;; externip=69.91.84.176 ; lba
externip=larryalk.dyndns.org ; lba
;externip = 200.201.202.203 ; Address that we're going to put in outbound SIP messages
; if we're behind a NAT
; The externip and localnet is used
; when registering and communicating with other proxies
; that we're registered with
;externhost=foo.dyndns.net ; Alternatively you can specify an
; external host, and Asterisk will
; perform DNS queries periodically. Not
; recommended for production
; environments! Use externip instead
;externrefresh=10 ; How often to refresh externhost if
; used
; You may add multiple local networks. A reasonable set of defaults
; are:
localnet=192.168.0.0/255.255.255.0 ; lba
;localnet=192.168.0.0/255.255.0.0; All RFC 1918 addresses are local networks
;localnet=10.0.0.0/255.0.0.0 ; Also RFC1918
;localnet=172.16.0.0/12 ; Another RFC1918 with CIDR notation
;localnet=169.254.0.0/255.255.0.0 ;Zero conf local network
; The nat= setting is used when Asterisk is on a public IP, communicating with
; devices hidden behind a NAT device (broadband router). If you have one-way
; audio problems, you usually have problems with your NAT configuration or your
; firewall's support of SIP+RTP ports. You configure Asterisk choice of RTP
; ports for incoming audio in rtp.conf
;
nat=yes ; lba set at A*UG meeting
;nat=no ; Global NAT settings (Affects all peers and users)
; yes = Always ignore info and assume NAT
; no = Use NAT mode only according to RFC3581
; never = Never attempt NAT mode or RFC3581 support
; route = Assume NAT, don't send rport
; (work around more UNIDEN bugs)
;----------------------------------------- NAT SUPPORT Ends ------------------------
;rtcachefriends=yes ; Cache realtime friends by adding them to the internal list
; just like friends added from the config file only on a
; as-needed basis? (yes|no)
;rtupdate=yes ; Send registry updates to database using realtime? (yes|no)
; If set to yes, when a SIP UA registers successfully, the ip address,
; the origination port, the registration period, and the username of
; the UA will be set to database via realtime. If not present, defaults to 'yes'.
;rtautoclear=yes ; Auto-Expire friends created on the fly on the same schedule
; as if it had just registered? (yes|no|<seconds>)
; If set to yes, when the registration expires, the friend will vanish from
; the configuration until requested again. If set to an integer,
; friends expire within this number of seconds instead of the
; registration interval.
;ignoreregexpire=yes ; Enabling this setting has two functions:
;
; For non-realtime peers, when their registration expires, the information
; will _not_ be removed from memory or the Asterisk database; if you attempt
; to place a call to the peer, the existing information will be used in spite
; of it having expired
;
; For realtime peers, when the peer is retrieved from realtime storage,
; the registration information will be used regardless of whether
; it has expired or not; if it expires while the realtime peer is still in
; memory (due to caching or other reasons), the information will not be
; removed from realtime storage
; Incoming INVITE and REFER messages can be matched against a list of 'allowed'
; domains, each of which can direct the call to a specific context if desired.
; By default, all domains are accepted and sent to the default context or the
; context associated with the user/peer placing the call.
; Domains can be specified using:
; domain=<domain>[,<context>]
; Examples:
; domain=myasterisk.dom
; domain=customer.com,customer-context
;
; In addition, all the 'default' domains associated with a server should be
; added if incoming request filtering is desired.
; autodomain=yes
;
; To disallow requests for domains not serviced by this server:
; allowexternaldomains=no
; fromdomain=mydomain.tld ; When making outbound SIP INVITEs to
; non-peers, use your primary domain "identity"
; for From: headers instead of just your IP
; address. This is to be polite and
; it may be a mandatory requirement for some
; destinations which do not have a prior
; account relationship with your server.
[authentication]
; Global credentials for outbound calls, i.e. when a proxy challenges your
; Asterisk server for authentication. These credentials override
; any credentials in peer/register definition if realm is matched.
;
; This way, Asterisk can authenticate for outbound calls to other
; realms. We match realm on the proxy challenge and pick an set of
; credentials from this list
; Syntax:
; auth = <user>:<secret>@<realm>
; auth = <user>#<md5secret>@<realm>
; Example:
;auth=mark:topsecret@digium.com
;
; You may also add auth= statements to [peer] definitions
; Peer auth= override all other authentication settings if we match on realm
;------------------------------------------------------------------------------
; Users and peers have different settings available. Friends have all settings,
; since a friend is both a peer and a user
;-------------------------------------------------------------------------------
;
; User config options: Peer configuration:
; -------------------- -------------------
; context context
; permit permit
; deny deny
; secret secret
; md5secret md5secret
; dtmfmode dtmfmode
; canreinvite canreinvite
; nat nat
; callgroup callgroup
; pickupgroup pickupgroup
; language language
; allow allow
; disallow disallow
; insecure insecure
; trustrpid trustrpid
; progressinband progressinband
; promiscredir promiscredir
; useclientcode useclientcode
; accountcode accountcode
; setvar setvar
; callerid callerid
; amaflags amaflags
; call-limit call-limit
; restrictcid restrictcid
; subscribecontext subscribecontext
; mailbox
; username
; template
; fromdomain
; regexten
; fromuser
; host
; port
; qualify
; defaultip
; rtptimeout
; rtpholdtimeout
; sendrpid
; -----------------------------------------------------------------------------------
; Everything in original sip.conf below this line was deleted at Installfest 2/20/06:
; Lines below are lba specific settings:
; -----------------------------------------------------------------------------------
[telasip-gw]
;context=default
context=telasip-out
type=peer
qualify=200
host=gw3.telasip.com
username=sanitized
secret=sanitized
insecure=very
canreinvite=no
callerid="Larry Alkoff" <5123011414>
nat=yes
[120]
context=default
username=120
type=friend
qualify=yes
insecure=very
host=dynamic
canreinvite=no
nat=no
; Above lines created at Installfest.
; lba: extensions.conf - configure all inbound & outbound calls & dialplans here:
;
; Static extension configuration file, used by
; the pbx_config module. This is where you configure all your
; inbound and outbound calls in Asterisk.
;
; This configuration file is reloaded
; - With the "extensions reload" command in the CLI
; - With the "reload" command (that reloads everything) in the CLI
;
; The "General" category is for certain variables.
;
[general]
;
; If static is set to no, or omitted, then the pbx_config will rewrite
; this file when extensions are modified. Remember that all comments
; made in the file will be lost when that happens.
;
; XXX Not yet implemented XXX
;
static=yes
;
; if static=yes and writeprotect=no, you can save dialplan by
; CLI command 'save dialplan' too
;
writeprotect=no
;
; If autofallthrough is set, then if an extension runs out of
; things to do, it will terminate the call with BUSY, CONGESTION
; or HANGUP depending on Asterisk's best guess (strongly recommended).
;
; If autofallthrough is not set, then if an extension runs out of
; things to do, asterisk will wait for a new extension to be dialed
; (this is the original behavior of Asterisk 1.0 and earlier).
;
autofallthrough=yes
;
; If clearglobalvars is set, global variables will be cleared
; and reparsed on an extensions reload, or Asterisk reload.
;
; If clearglobalvars is not set, then global variables will persist
; through reloads, and even if deleted from the extensions.conf or
; one if its included files, will remain set to the previous value.
;
clearglobalvars=no
;
; If priorityjumping is set to 'yes', then applications that support
; 'jumping' to a different priority based on the result of their operations
; will do so (this is backwards compatible behavior with pre-1.2 releases
; of Asterisk). Individual applications can also be requested to do this
; by passing a 'j' option in their arguments.
;
priorityjumping=no
;
; You can include other config files, use the #include command
; (without the ';'). Note that this is different from the "include" command
; that includes contexts within other contexts. The #include command works
; in all asterisk configuration files.
;#include "filename.conf"
; ------------------------ Globals ------------------------------
; The "Globals" category contains global variables that can be referenced
; in the dialplan with ${VARIABLE} or ${ENV(VARIABLE)} for Environmental
; variables,
; ${${VARIABLE}} or ${text${VARIABLE}} or any hybrid
;
[globals]
CONSOLE=Console/dsp ; Console interface for demo
;CONSOLE=Zap/1
;CONSOLE=Phone/phone0
IAXINFO=guest ; IAXtel username/password
;IAXINFO=myuser:mypass
TRUNK=Zap/g2 ; Trunk interface
;
; Note the 'g2' in the TRUNK variable above. It specifies which group (defined
; in zapata.conf) to dial, i.e. group 2, and how to choose a channel to use in
; the specified group. The four possible options are:
;
; g: select the lowest-numbered non-busy Zap channel
; (aka. ascending sequential hunt group).
; G: select the highest-numbered non-busy Zap channel
; (aka. descending sequential hunt group).
; r: use a round-robin search, starting at the next highest channel than last
; time (aka. ascending rotary hunt group).
; R: use a round-robin search, starting at the next lowest channel than last
; time (aka. descending rotary hunt group).
;
TRUNKMSD=1 ; MSD digits to strip (usually 1 or 0)
;TRUNK=IAX2/user:pass@provider
; ------------------------ Globals End ------------------------------
; ------------------------ lba Tutorial -----------------------------
;
; Any category other than "General" and "Globals" represent
; extension contexts, which are collections of extensions.
;
; Extension names may be numbers, letters, or combinations
; thereof. If an extension name is prefixed by a '_'
; character, it is interpreted as a pattern rather than a
; literal. In patterns, some characters have special meanings:
;
; X - any digit from 0-9
; Z - any digit from 1-9
; N - any digit from 2-9
; [1235-9] - any digit in the brackets (in this example, 1,2,3,5,6,7,8,9)
; . - wildcard, matches anything remaining (e.g. _9011. matches
; anything starting with 9011 excluding 9011 itself)
; ! - wildcard, causes the matching process to complete as soon as
; it can unambiguously determine that no other matches are possible
;
; For example the extension _NXXXXXX would match normal 7 digit dialings,
; while _1NXXNXXXXXX would represent an area code plus phone number
; preceeded by a one.
;
; Each step of an extension is ordered by priority, which must
; always start with 1 to be considered a valid extension. The priority
; "next" or "n" means the previous priority plus one, regardless of whether
; the previous priority was associated with the current extension or not.
; The priority "same" or "s" means the same as the previously specified
; priority, again regardless of whether the previous entry was for the
; same extension. Priorities may be immediately followed by a plus sign
; and another integer to add that amount (most useful with 's' or 'n').
; Priorities may then also have an alias, or label, in
; parenthesis after their name which can be used in goto situations
;
; Contexts contain several lines, one for each step of each
; extension, which can take one of two forms as listed below,
; with the first form being preferred. One may include another
; context in the current one as well, optionally with a
; date and time. Included contexts are included in the order
; they are listed.
;
;[context]
;exten => someexten,priority[+offset][(alias)],application(arg1,arg2,...)
;exten => someexten,priority[+offset][(alias)],application,arg1|arg2...
; lba Dial() application:
; exten => _91.,2,Dial(SIP/${EXTEN:1}@telasip-gw)
; dest#
; priority
; Dial() command w/4 arguments: (2 & 3 may be omitted)
; 1 remote resource/channel number eg: SIP/${EXTEN:1}
; 2 timeout (not incl here)
; 3 option string (not incl here)
; 4 url or POTS number
;
; ------------------------ lba Tutorial Ends -----------------------------
;
; Timing list for includes is
;
; <time range>|<days of week>|<days of month>|<months>
;
;include => daytime|9:00-17:00|mon-fri|*|*
;
; ignorepat can be used to instruct drivers to not cancel dialtone upon
; receipt of a particular pattern. The most commonly used example is
; of course '9' like this:
;
;ignorepat => 9
;
; so that dialtone remains even after dialing a 9.
;
;
; Sample entries for extensions.conf:
; -----------------------------------
;
[dundi-e164-canonical]
;
; List canonical entries here
;
;exten => 12564286000,1,Macro(std-exten,6000,IAX2/foo)
;exten => _125642860XX,1,Dial(IAX2/otherbox/${EXTEN:7})
[dundi-e164-customers]
;
; If you are an ITSP or Reseller, list your customers here.
;
;exten => _12564286000,1,Dial(SIP/customer1)
;exten => _12564286001,1,Dial(IAX2/customer2)
[dundi-e164-via-pstn]
;
; If you are freely delivering calls to the PSTN, list them here
;
;exten => _1256428XXXX,1,Dial(Zap/g2/${EXTEN:7}) ; Expose all of 256-428
;exten => _1256325XXXX,1,Dial(Zap/g2/${EXTEN:7}) ; Ditto for 256-325
[dundi-e164-local]
;
; Context to put your dundi IAX2 or SIP user in for
; full access
;
include => dundi-e164-canonical
include => dundi-e164-customers
include => dundi-e164-via-pstn
[dundi-e164-switch]
;
; Just a wrapper for the switch
;
switch => DUNDi/e164
[dundi-e164-lookup]
;
; Locally to lookup, try looking for a local E.164 solution
; then try DUNDi if we don't have one.
;
include => dundi-e164-local
include => dundi-e164-switch
;
; DUNDi can also be implemented as a Macro instead of using
; the Local channel driver.
;
[macro-dundi-e164]
;
; ARG1 is the extension to Dial
;
exten => s,1,Goto(${ARG1},1)
include => dundi-e164-lookup
;
; Here are the entries you need to participate in the IAXTEL
; call routing system. Most IAXTEL numbers begin with 1-700, but
; there are exceptions. For more information, and to sign
; up, please go to www.gnophone.com or www.iaxtel.com
;
[iaxtel700]
exten => _91700XXXXXXX,1,Dial(IAX2/${IAXINFO}@iaxtel.com/${EXTEN:1}@iaxtel)
;
; The SWITCH statement permits a server to share the dialplain with
; another server. Use with care: Reciprocal switch statements are not
; allowed (e.g. both A -> B and B -> A), and the switched server needs
; to be on-line or else dialing can be severly delayed.
;
[iaxprovider]
;switch => IAX2/user:[key]@myserver/mycontext
[trunkint]
;
; International long distance through trunk
;
exten => _9011.,1,Macro(dundi-e164,${EXTEN:4})
exten => _9011.,n,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
[trunkld]
;
; Long distance context accessed through trunk
;
exten => _91NXXNXXXXXX,1,Macro(dundi-e164,${EXTEN:1})
exten => _91NXXNXXXXXX,n,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
[trunklocal]
;
; Local seven-digit dialing accessed through trunk interface
;
;; ??? exten => _9NXXXXXX,1,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
[trunktollfree]
;
; Long distance context accessed through trunk interface
;
exten => _91800NXXXXXX,1,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
exten => _91888NXXXXXX,1,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
exten => _91877NXXXXXX,1,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
exten => _91866NXXXXXX,1,Dial(${TRUNK}/${EXTEN:${TRUNKMSD}})
[international]
;
; Master context for international long distance
;
ignorepat => 9
include => longdistance
include => trunkint
[longdistance]
;
; Master context for long distance
;
ignorepat => 9
include => local
include => trunkld
[local]
;
; Master context for local, toll-free, and iaxtel calls only
;
ignorepat => 9
include => default
include => parkedcalls
include => trunklocal
include => iaxtel700
include => trunktollfree
include => iaxprovider
;
; You can use an alternative switch type as well, to resolve
; extensions that are not known here, for example with remote
; IAX switching you transparently get access to the remote
; Asterisk PBX
;
; switch => IAX2/user:password@bigserver/local
;
; An "lswitch" is like a switch but is literal, in that
; variable substitution is not performed at load time
; but is passed to the switch directly (presumably to
; be substituted in the switch routine itself)
;
; lswitch => Loopback/12${EXTEN}@othercontext
;
; An "eswitch" is like a switch but the evaluation of
; variable substitution is performed at runtime before
; being passed to the switch routine.
;
; eswitch => IAX2/context@${CURSERVER}
[macro-stdexten];
;
; Standard extension macro:
; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well
; ${ARG2} - Device(s) to ring
;
exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum
exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER)
exten => s-NOANSWER,1,Voicemail(u${ARG1}) ; If unavailable, send to voicemail w/ unavail announce
exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start
exten => s-BUSY,1,Voicemail(b${ARG1}) ; If busy, send to voicemail w/ busy announce
exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start
exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer
exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain
[macro-stdPrivacyexten];
;
; Standard extension macro:
; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well
; ${ARG2} - Device(s) to ring
; ${ARG3} - Optional DONTCALL context name to jump to (assumes the s,1 extension-priority)
; ${ARG4} - Optional TORTURE context name to jump to (assumes the s,1 extension-priority)`
;
exten => s,1,Dial(${ARG2},20|p) ; Ring the interface, 20 seconds maximum, call screening option (or use P for databased call screening)
exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER)
exten => s-NOANSWER,1,Voicemail(u${ARG1}) ; If unavailable, send to voicemail w/ unavail announce
exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start
exten => s-BUSY,1,Voicemail(b${ARG1}) ; If busy, send to voicemail w/ busy announce
exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start
exten => s-DONTCALL,1,Goto(${ARG3},s,1) ; Callee chose to send this call to a polite "Don't call again" script.
exten => s-TORTURE,1,Goto(${ARG4},s,1) ; Callee chose to send this call to a telemarketer torture script.
exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer
exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain
[demo]
;
; We start with what to do when a call first comes in.
;
exten => s,1,Wait,1 ; Wait a second, just for fun
exten => s,n,Answer ; Answer the line
exten => s,n,Set(TIMEOUT(digit)=5) ; Set Digit Timeout to 5 seconds
exten => s,n,Set(TIMEOUT(response)=10) ; Set Response Timeout to 10 seconds
exten => s,n(restart),BackGround(demo-congrats) ; Play a congratulatory message
exten => s,n(instruct),BackGround(demo-instruct) ; Play some instructions
exten => s,n,WaitExten ; Wait for an extension to be dialed.
exten => 2,1,BackGround(demo-moreinfo) ; Give some more information.
exten => 2,n,Goto(s,instruct)
exten => 3,1,Set(LANGUAGE()=fr) ; Set language to french
exten => 3,n,Goto(s,restart) ; Start with the congratulations
exten => 1000,1,Goto(default,s,1)
;
; We also create an example user, 1234, who is on the console and has
; voicemail, etc.
;
exten => 1234,1,Playback(transfer,skip) ; "Please hold while..."
; (but skip if channel is not up)
exten => 1234,n,Macro(stdexten,1234,${CONSOLE})
exten => 1235,1,Voicemail(u1234) ; Right to voicemail
exten => 1236,1,Dial(Console/dsp) ; Ring forever
exten => 1236,n,Voicemail(u1234) ; Unless busy
;
; # for when they're done with the demo
;
exten => #,1,Playback(demo-thanks) ; "Thanks for trying the demo"
exten => #,n,Hangup ; Hang them up.
;
; A timeout and "invalid extension rule"
;
exten => t,1,Goto(#,1) ; If they take too long, give up
exten => i,1,Playback(invalid) ; "That's not valid, try again"
;
; Create an extension, 500, for dialing the
; Asterisk demo.
;
exten => 500,1,Playback(demo-abouttotry); Let them know what's going on
exten => 500,n,Dial(IAX2/guest@misery.digium.com/s@default) ; Call the Asterisk demo
exten => 500,n,Playback(demo-nogo) ; Couldn't connect to the demo site
exten => 500,n,Goto(s,6) ; Return to the start over message.
;
; Create an extension, 600, for evaulating echo latency.
;
exten => 600,1,Playback(demo-echotest) ; Let them know what's going on
exten => 600,n,Echo ; Do the echo test
exten => 600,n,Playback(demo-echodone) ; Let them know it's over
exten => 600,n,Goto(s,6) ; Start over
;
; Give voicemail at extension 8500
;
exten => 8500,1,VoicemailMain
exten => 8500,n,Goto(s,6)
;
; Here's what a phone entry would look like (IXJ for example)
;
;exten => 1265,1,Dial(Phone/phone0,15)
;exten => 1265,n,Goto(s,5)
;[mainmenu]
;
; Example "main menu" context with submenu
;
;exten => s,1,Answer
;exten => s,n,Background(thanks) ; "Thanks for calling press 1 for sales, 2 for support, ..."
;exten => s,n,WaitExten
;exten => 1,1,Goto(submenu,s,1)
;exten => 2,1,Hangup
;include => default
;
;[submenu]
;exten => s,1,Ringing ; Make them comfortable with 2 seconds of ringback
;exten => s,n,Wait,2
;exten => s,n,Background(submenuopts) ; "Thanks for calling the sales department. Press 1 for steve, 2 for..."
;exten => s,n,WaitExten
;exten => 1,1,Goto(default,steve,1)
;exten => 2,1,Goto(default,mark,2)
[telasip-out]
; lba These extensions added at Installfest 2/20/06:
; They should be in separate telasip-in and telasip-out contexts, not default!
;; below extensions work but you have to dial 91+area code first
; [telasipin]
;;exten => _512879677[67],1,Dial(SIP/120)
; [telasipout]
;;this works but its a PITA to dial 91+area code:
;;exten => _91.,1,SetCallerID(5123011414)
;;exten => _91.,2,Dial(SIP/${EXTEN:1}@telasip-gw)
;; These work for local calls:
exten => _NXXXXXX,1,SetCallerID(512-301-1414)
exten => _NXXXXXX,2,Dial(SIP/1512${EXTEN}@telasip-gw)
;; for long distance calls without dialing 1:
exten => _NXXNXXXXXX,1,SetCallerID(512-301-1414)
exten => _NXXNXXXXXX,2,Dial(SIP/1${EXTEN}@telasip-gw)
;; for long distance calls with a dialed 1:
exten => _1NXXNXXXXXX,1,SetCallerID(512-301-1414)
exten => _1NXXNXXXXXX,2,Dial(SIP/1${EXTEN:1}@telasip-gw)
;;[local-lba]
;; ?? exten => _NXXXXXX,1,Dial(SIP/${EXTEN:1}@telasip-gw)
[new1]
; lba gil call info
exten => 1212,1,Dial(SIP/18005551212@telasip-gw)
[new2]
exten => 1512,1,Dial(SIP/18005551212@telasip-gw)
;; lba [default] context set in sip.conf
[default]
;
; By default we include the demo. In a production system, you
; probably don't want to have the demo there.
;
;include => demo
;;exten => 1212,1,Dial(SIP/18005551212@telasip-gw)
;exten => _1XX,1,Dial(SIP/${EXTEN})
exten => _1XX,1,Macro(stdexten,${EXTEN},SIP/${EXTEN})
; this works to dial the directory
exten => *411,1,Directory(default)
; end of Intallfest add
;
; Extensions like the two below can be used for FWD, Nikotel, sipgate etc.
; Note that you must have a [sipprovider] section in sip.conf whereas
; the otherprovider.net example does not require such a peer definition
;
;exten => _41X.,1,Dial(SIP/${EXTEN:2}@sipprovider,,r)
;exten => _42X.,1,Dial(SIP/user:passwd@${EXTEN:2}@otherprovider.net,30,rT)
; Real extensions would go here. Generally you want real extensions to be
; 4 or 5 digits long (although there is no such requirement) and start with a
; single digit that is fairly large (like 6 or 7) so that you have plenty of
; room to overlap extensions and menu options without conflict. You can alias
; them with names, too, and use global variables
;exten => 6245,hint,SIP/Grandstream1&SIP/Xlite1,Joe Schmoe ; Channel hints for presence
;exten => 6245,1,Dial(SIP/Grandstream1,20,rt) ; permit transfer
;exten => 6245,n(dial),Dial(${HINT},20,rtT) ; Use hint as listed
;exten => 6245,n,Voicemail(u6245) ; Voicemail (unavailable)
;exten => 6245,s+1,Hangup ; s+1, same as n
;exten => 6245,dial+101,Voicemail(b6245) ; Voicemail (busy)
;exten => 6361,1,Dial(IAX2/JaneDoe,,rm) ; ring without time limit
;exten => 6389,1,Dial(MGCP/aaln/1@192.168.0.14)
;exten => 6394,1,Dial(Local/6275/n) ; this will dial ${MARK}
;exten => 6275,1,Macro(stdexten,6275,${MARK}) ; assuming ${MARK} is something like Zap/2
;exten => mark,1,Goto(6275|1) ; alias mark to 6275
;exten => 6536,1,Macro(stdexten,6236,${WIL}) ; Ditto for wil
;exten => wil,1,Goto(6236|1)
;
; Some other handy things are an extension for checking voicemail via
; voicemailmain
;
;exten => 8500,1,VoicemailMain
;exten => 8500,n,Hangup
;
; Or a conference room (you'll need to edit meetme.conf to enable this room)
;
;exten => 8600,1,Meetme(1234)
;
; Or playing an announcement to the called party, as soon it answers
;
;exten = 8700,1,Dial(${MARK},30,A(/path/to/my/announcemsg))
;
; For more information on applications, just type "show applications" at your
; friendly Asterisk CLI prompt.
;
; 'show application <command>' will show details of how you
; use that particular application in this file, the dial plan.
;