RedBoot> load -r -v -b 0x600000 -m ymodem
Raw file loaded 0x00600000-0x0071343f, assumed entry at 0x00600000
xyzModem - CRC mode, 8811(SOH)/0(STX)/0(CAN) packets, 4 retries
RedBoot> exec
Using base address 0x00600000 and length 0x00113440
Uncompressing Linux........................................................................... done, booting the kernel.
Linux version 2.6.16-rc6-git1 (gs@gs) (gcc version 3.4.4) #1 PREEMPT Mon Mar 20 15:09:25 EST 2006
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE)
Machine: D-Link DSM-G600
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists
Kernel command line: noirqdebug console=ttyS0,115200n8 root=/dev/sda2 rootfstype=ext3 rootdelay=12
PID hash table entries: 512 (order: 9, 8192 bytes)
IXP4xx: FREQ=66666600 COUNT=666665
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62464KB available (2105K code, 183K data, 92K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:01.0 on pci bus
dmabounce: registered device 0000:00:03.0 on pci bus
IXP4xx: FREQ=66000000 COUNT=660001
dmabounce: registered device 0000:00:03.1 on pci bus
dmabounce: registered device 0000:00:03.2 on pci bus
dmabounce: registered device 0000:00:04.0 on pci bus
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
RAMDISK driver initialized: 4 RAM disks of 10240K size 1024 blocksize
VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.13
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
Copyright (c) 2004 Red Hat Inc.
PCI: enabling device 0000:00:04.0 (0140 -> 0143)
PCI: Via IRQ fixup for 0000:00:04.0, from 23 to 7
eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
eth0: Ethernet Address: 00:13:46:48:04:65
PCI: enabling device 0000:00:01.0 (0140 -> 0141)
ata1: PATA max UDMA/100 cmd 0x1450 ctl 0x1462 bmdma 0x1440 irq 24
ata2: PATA max UDMA/100 cmd 0x1458 ctl 0x1466 bmdma 0x1448 irq 24
ata1: dev 1 ATA-3, max UDMA/33, 12594960 sectors: LBA
ata1: dev 1 configured for UDMA/33
scsi0 : pata_artop
ATA: abnormal status 0x7F on port 0x145F
ata2: disabling port
scsi1 : pata_artop
Vendor: ATA Model: Maxtor 86480D6 Rev: NAVX
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 12594960 512-byte hdwr sectors (6449 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 12594960 512-byte hdwr sectors (6449 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:1:0: Attached scsi disk sda
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
RedBoot directory 0x50fe0000(0x20000) swapped
7 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 7 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00240000 : "kernel"
0x00240000-0x00840000 : "filesystem"
0x00840000-0x00ec0000 : "usr"
0x00f00000-0x00fc0000 : "sysconfig"
0x00fc0000-0x00fc1000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only
0x00fe0000-0x01000000 : "FIS directory"
Using configured DiskOnChip probe address 0x50000000
PCI: enabling device 0000:00:03.2 (0140 -> 0142)
PCI: Via IRQ fixup for 0000:00:03.2, from 25 to 9
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 25, io mem 0x48010000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: over-current change on port 2
USB Universal Host Controller Interface driver v2.3
PCI: enabling device 0000:00:03.0 (0140 -> 0141)
PCI: Via IRQ fixup for 0000:00:03.0, from 27 to 11
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:03.0: irq 27, io base 0x00001400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 3
PCI: enabling device 0000:00:03.1 (0140 -> 0141)
PCI: Via IRQ fixup for 0000:00:03.1, from 26 to 10
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:03.1: irq 26, io base 0x00001420
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Waiting 12sec before mounting root device...
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 92K
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Will now activate swap.
swapon on /dev/sda1
Adding 497972k swap on /dev/sda1. Priority:-1 extents:1 across:497972k
Done activating swap.
Will now check root file system.
fsck 1.39-WIP (31-Dec-2005)
fsck: fsck.default: not found
fsck: Error 2 while executing fsck.default for /dev/sda2
Done checking root file system.
A log will be saved in /var/log/fsck/checkroot if that location is writable.
EXT3 FS on sda2, internal journal
Setting the system clock..
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
System Clock set. Local time: Thu Jan 1 00:00:29 UTC 1970.
Cleaning up ifupdown...done.
Calculating module dependencies...done.
Loading modules...
All modules loaded.
Setting the system clock again..
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
System Clock set. Local time: Thu Jan 1 00:00:30 UTC 1970.
Will now check all file systems.
fsck 1.39-WIP (31-Dec-2005)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables ...
... done.
Will now mount local filesystems.
mount: usbfs already mounted on /proc/bus/usb
tmpfs on /tmp type tmpfs (rw,noatime)
Done mounting local filesystems.
Will now activate swapfile swap.
Done activating swapfile swap.
Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
Setting up networking...done.
Setting hostname to 'Sid-DSM-G600'...done.
Configuring network interfaces.../bin/sh: iptables-restore: command not found
Failed to bring up lo.
Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.
Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html
Velocity is AUTO mode
NET: Registered protocol family 17
Listening on LPF/eth0/00:13:46:48:04:65
Sending on LPF/eth0/00:13:46:48:04:65
Sending on Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
eth0: Link autonegation speed 100M bps full duplex
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPOFFER from 192.168.123.254
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.123.254
bound to 192.168.123.139 -- renewal in 3599400 seconds.
done.
Running ntpdate to synchronize clock.
Initializing random number generator...done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting internet superserver: inetd.
Starting OpenBSD Secure Shell server: sshd.
Starting periodic command scheduler....
Debian GNU/Linux testing/unstable Sid-DSM-G600 ttyS0
Sid-DSM-G600 login: root
Password:
Last login: Thu Jan 1 00:02:33 1970 on ttyS0
Linux Sid-DSM-G600 2.6.16-rc6-git1 #1 PREEMPT Mon Mar 20 15:09:25 EST 2006 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Sid-DSM-G600:~# hwclock --systohc
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Sid-DSM-G600:~# hwclock --debug --systohc
hwclock from util-linux-2.12r
hwclock: Open of /dev/rtc failed, errno=2: No such file or directory.
No usable clock interface found.
Cannot access the Hardware Clock via any known method.
Sid-DSM-G600:~# ls -l /dev/rtc*
ls: /dev/rtc*: No such file or directory
Sid-DSM-G600:~# ls