rendered paste bodysanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000000f6d0000 end: 000000000f7d0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000f7d0000 size: 000000000001fc00 end: 000000000f7efc00 type: 2
copy_e820_map() start: 000000000f7efc00 size: 000000000000b400 end: 000000000f7fb000 type: 4
copy_e820_map() start: 000000000f7fb000 size: 0000000000005000 end: 000000000f800000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f0000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000002000 end: 00000000fec02000 type: 2
copy_e820_map() start: 00000000fed20000 size: 000000000007b000 end: 00000000fed9b000 type: 2
copy_e820_map() start: 00000000feda0000 size: 0000000000020000 end: 00000000fedc0000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000100000 end: 00000000ffc00000 type: 2
copy_e820_map() start: 00000000fff00000 size: 0000000000100000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f7d0000 (usable)
BIOS-e820: 000000000f7d0000 - 000000000f7efc00 (reserved)
BIOS-e820: 000000000f7efc00 - 000000000f7fb000 (ACPI NVS)
BIOS-e820: 000000000f7fb000 - 000000000f800000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 63440) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 63440
HighMem 63440 -> 63440
early_node_map[1] active PFN ranges
0: 0 -> 63440
On node 0 totalpages: 63440
DMA zone: 40 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4056 pages, LIFO batch:0
Normal zone: 579 pages used for memmap
Normal zone: 58765 pages, LIFO batch:15
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 HP ) @ 0x000fe270
ACPI: RSDT (v001 HP 099C 0x25020520 HP 0x00000001) @ 0x0f7efc84
ACPI: FADT (v002 HP 099C 0x00000002 HP 0x00000001) @ 0x0f7efc00
ACPI: MADT (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x0f7efcb4
ACPI: MCFG (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x0f7efd10
ACPI: DSDT (v001 HP DAU00 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfec01000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 0f800000:d0800000)
Detected 1400.243 MHz processor.
Built 1 zonelists. Total pages: 62821
Kernel command line: ro root=LABEL=/ rhgb quiet rhgb quiet selinux=0
mapped APIC to ffffd000 (fec01000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07ab000 soft=c078b000
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244664k/253760k available (2189k kernel code, 8576k reserved, 1159k data, 236k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0000000 - 0xff7fe000 ( 759 MB)
lowmem : 0xc0000000 - 0xcf7d0000 ( 247 MB)
.init : 0xc074b000 - 0xc0786000 ( 236 kB)
.data : 0xc0623649 - 0xc0745494 (1159 kB)
.text : 0xc0400000 - 0xc0623649 (2189 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2802.31 BogoMIPS (lpj=1401157)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9f3bf 00000000 00000000 00002040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Celeron(R) M processor 1.40GHz stepping 06
Total of 1 processors activated (2802.31 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=40 bytes
sizeof(inode)=420 bytes
sizeof(dentry)=144 bytes
sizeof(ext3inode)=596 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1408 bytes
HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [C002] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C002] bus is 0
Boot video device is 0000:00:02.0
PCI: Enabled ICH6/i801 SMBus device
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH6 GPIO
0000:00:1f.1: trying to change BAR0 from 0000 to 01F0
0000:00:1f.1: trying to change BAR1 from 0000 to 03F4
0000:00:1f.1: trying to change BAR2 from 0000 to 0170
0000:00:1f.1: trying to change BAR3 from 0000 to 0374
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C002.C067._PRT]
ACPI: Power Resource [C1BD] (on)
ACPI: PCI Interrupt Link [C0D7] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0D8] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0ED] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0EE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0EF] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0F0] (IRQs 10 11) *0, disabled.
ACPI: Power Resource [C250] (off)
ACPI: Power Resource [C251] (off)
ACPI: Power Resource [C252] (off)
ACPI: Power Resource [C253] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:09: ioport range 0x1000-0x107f could not be reserved
pnp: 00:09: ioport range 0x1100-0x113f has been reserved
pnp: 00:09: ioport range 0x1200-0x121f has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 10000000-13ffffff
MEM window: 14000000-17ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: d0000000-d03fffff
PREFETCH window: 10000000-13ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 5, 163840 bytes)
TCP bind hash table entries: 4096 (order: 4, 81920 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1487k freed
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1177766483.728:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ksign: Installing public key data
Loading keyring
- Added public key 93BB43D45D46D1B4
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Transitioning device [C254] to D3
ACPI: Transitioning device [C254] to D3
ACPI: Fan [C254] (off)
ACPI: Transitioning device [C255] to D3
ACPI: Transitioning device [C255] to D3
ACPI: Fan [C255] (off)
ACPI: Transitioning device [C256] to D3
ACPI: Transitioning device [C256] to D3
ACPI: Fan [C256] (off)
ACPI: Transitioning device [C257] to D3
ACPI: Transitioning device [C257] to D3
ACPI: Fan [C257] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (75 C)
ACPI: Thermal Zone [TZ2] (55 C)
ACPI: Thermal Zone [TZ3] (30 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 18
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2580-0x2587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: TOSHIBA MK4026GAX, ATA DISK drive
hdb: TSSTcorpCDW/DVD TS-L462A, ATAPI CD/DVD-ROM drive
hda: hw_config=403d
hda: hw_config=403d
hdb: hw_config=0000
hdb: hw_config=0000
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB), CHS=65535/16/63<6>hda: hw_config=403d
, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:02:06.0 [103c:099c]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x01aa1b22, devctl 0x64
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000820
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd03fffff
pcmcia: parent PCI bridge Memory window: 0x10000000 - 0x13ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1BA,PNP0f13:C1BB] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 236k freed
Write protecting the kernel read-only data: 841k
Time: tsc clocksource has been installed.
Time: acpi_pm clocksource has been installed.
firmware_class: attempt to set timeout to 10
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00002000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 20, io base 0x00002020
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00002040
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 21, io base 0x00002060
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
pccard: CardBus card inserted into slot 0
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:03:00.0: irq 16, io mem 0x14000000
input: AT Translated Set 2 keyboard as /class/input/input2
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
hub 1-2:1.0: 4 ports detected
PCI: Enabling device 0000:03:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.1 to 64
ohci_hcd 0000:03:00.1: OHCI Host Controller
ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:03:00.1: irq 16, io mem 0x14001000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xd0580000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 8 ports detected
usb 1-2.3: new low speed USB device using uhci_hcd and address 3
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 1-2:1.0: cannot disable port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 1-2:1.0: cannot disable port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 1-2:1.0: cannot disable port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: cannot reset port 3 (err = -71)
hub 1-2:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 1-2:1.0: cannot disable port 3 (err = -71)
hub 1-2:1.0: cannot disable port 3 (err = -71)
hub 1-2:1.0: hub_port_status failed (err = -71)
usb 1-2: USB disconnect, address 2
PCI: Enabling device 0000:03:00.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.2[C] -> GSI 18 (level, low) -> IRQ 16
ehci_hcd 0000:03:00.2: EHCI Host Controller
ehci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 8
ehci_hcd 0000:03:00.2: irq 16, io mem 0x14002000
ehci_hcd 0000:03:00.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 5 ports detected
usb 7-2: new high speed USB device using ehci_hcd and address 2
SCSI subsystem initialized
libata version 2.00 loaded.
usb 7-2: configuration #1 chosen from 1 choice
hub 7-2:1.0: USB hub found
hub 7-2:1.0: 4 ports detected
usb 7-2.3: new low speed USB device using ehci_hcd and address 3
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
usb 7-2.3: configuration #1 chosen from 1 choice
input: PATEN USB Receiver as /class/input/input3
input: USB HID v1.10 Keyboard [PATEN USB Receiver] on usb-0000:00:1d.7-2.3
input: PATEN USB Receiver as /class/input/input4
input: USB HID v1.10 Device [PATEN USB Receiver] on usb-0000:00:1d.7-2.3
input: PATEN USB Receiver as /class/input/input5
input: USB HID v1.10 Mouse [PATEN USB Receiver] on usb-0000:00:1d.7-2.3
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 7300220
EXT3-fs: hda3: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
intel_rng: FWH not detected
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:06.2[C] -> GSI 22 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[d0001000-d00017ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20
input: PC Speaker as /class/input/input6
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 18
eth0: Broadcom 4400 10/100BaseT Ethernet 00:14:38:05:c4:92
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 21 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1e.2 to 64
AC'97 0 analog subsections not ready
ieee1394: Host added: ID:BUS[0-00:1023] GUID[718b5000291928a6]
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
intel8x0_measure_ac97_clock: measured 50378 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1e.3 to 64
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
sonypi: Sony Programmable I/O Controller Driver v1.26.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: AC Adapter [C16B] (on-line)
ACPI: Battery Slot [C16D] (battery present)
ACPI: Battery Slot [C16C] (battery absent)
input: Power Button (FF) as /class/input/input7
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input8
ACPI: Sleep Button (CM) [C1E0]
input: Lid Switch as /class/input/input9
ACPI: Lid Switch [C1E1]
No dock devices found.
ibm_acpi: ec object not found
ACPI: Video Device [C054] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3 FS on hda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 522104k swap on /dev/hda2. Priority:-1 extents:1 across:522104k
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 18
[drm] Initialized i915 1.6.0 20060119 on minor 0
[root@localhost Qid]#